Search Results

During 1991 Volvo Car Corporation has introduced the new Volvo 850 GLT model featuring front wheel drive with transverse installation of the engine and gearbox. The powertrain; consists of a new in-line five-cylinder engine in combination with a four speed electronically controlled automatic gearbox or a five speed manual gearbox. The engine features DOHC 20 valves, V-VIS (Volvo Variable Induction System), well tuned exhaust system and microprocessor controlled engine management systems. The engine was designed and developed as a new member of Volvo's modular engine family. The first member was the in-line six-cylinder engine B6304F [1] introduced in 1990. The modular engines have a large number of identical components and the major components are machined in common transfer lines which makes the manufacturing process highly rational and cost-effective.

A single-cylinder engine was operated in HCCI combustion mode with different kinds of commercial fuels. The HCCI combustion was generated by creating a negative valve overlap (early exhaust valve closing combined with late intake valve opening) thus trapping a large amount of residuals (∼ 55%). Fifteen different fuels with high octane numbers were tested six of which were primary reference fuels (PRF's) and nine were commercial fuels or reference fuels. The engine was operated at constant operational parameters (speed/load, valve timing and equivalence ratio, intake air temperature, compression ratio, etc.) changing only the fuel type while the engine was running. Changing the fuel affected the auto-ignition timing, represented by the 50% mass fraction burned location (CA50). However these changes were not consistent with the classical RON and MON numbers, which are measures of the knock resistance of the fuel. Indeed, no correlation was found between CA50 and the RON or MON numbers.

Car accident investigations have shown that the head, the chest and the abdomen are the three most vulnerable body regions in side impacts, when serious-to-fatal (MAIS 3-6) injuries are considered. Injuries are much more common to occupants seated on the struck side than to those on the non-struck side. The development of new side impact protection systems has therefore been focused on struck side occupants. The first airbag system for side impact protection, jointly developed by Volvo and Autoliv, was introduced on the market in 1994. The SIPS bag is seat-mounted and protects mainly the chest and the abdomen, and also to some extent the head, since the head's lateral relative displacement is reduced by the side airbag, thereby keeping the head inside the car's outer profile. However, if an external object is exposed in the head area, for example in a truck-to-car side impact or in a single car collision into a pole or a tree, there is a need for an additional head protection device.

Approximately 25 % of a passenger vehicle’s aerodynamic drag comes directly or indirectly from its wheels, indicating that the rim geometry is highly relevant for increasing the vehicle’s overall energy efficiency. An extensive experimental study is presented where a parametric model of the rim design was developed, and statistical methods were employed to isolate the aerodynamic effects of certain geometric rim parameters. In addition to wind tunnel force measurements, this study employed the flowfield measurement techniques of wake surveys, wheelhouse pressure measurements, and base pressure measurements to investigate and explain the most important parameters’ effects on the flowfield. In addition, a numerical model of the vehicle with various rim geometries was developed and used to further elucidate the effects of certain geometric parameters on the flow field.

Bushing elasticity is one of the most important compliance factors that significantly influence driving behavior. The deformations of the bushings change the wheel orientations under external forces. Another important factor of bushing compliance is to provide a comfortable driving experience by isolating the vibrations from road irregularities. However, the driving comfort and driving dynamics are often in conflict and need to be balanced in terms of bushing compliance design. Specifically, lateral force steer and brake force steer are closely related to safety and stability and comprises must be minimized. The sensitivity analysis helps engineers to understand the critical bushing for certain compliance attributes, but optimal balancing is complicated to understand. The combination of individual bushing stiffness must be carefully set to achieve an acceptable level of all the attributes.

An experimental study of EGR and turbocharging concepts has been performed on an experimental 2.0-litre 4-cylinder turbocharged Euro6 light-duty diesel engine. The purpose of the study was to investigate the emissions and fuel consumption trade-off for different concept combinations. The impact of low-pressure and high-pressure EGR was studied in terms of engine-out emissions and fuel consumption. Moreover, the influence of single-stage and two-stage turbocharging was investigated in combination with the EGR systems, and how the engine efficiency could be further improved after engine calibration optimization. During low load engine operation where throttling may be required to achieve the desired low-pressure EGR rate, the difference in fuel consumption impact was studied for exhaust throttling and intake throttling, respectively. The cooling impact on high-pressure EGR was compared in terms of emissions and fuel consumption.

Since several decades, passenger cars and light duty vehicles (LDV) with spark-ignited engines reach full pollutant conversion during warm up conditions; the major challenge has been represented by the cold start and warming up strategies. The focus on technology developments of exhaust after treatment systems have been done in the thermal management in order to reach the warm up conditions as soon as possible. A new challenge is now represented by the Real Driving Emission (RDE) Regulation as this bring more various, and not any longer cycle defined, cold start conditions. On the other hand, once the full conversion has been reached, it would be beneficial for many Exhaust After Treatment System (EATS) components, e.g. for overall durability if the exhaust gas temperature could be lowered. To take significant further emission steps, approaching e.g. zero emission concepts, we investigate the use of Electrical Heating Catalyst (EHC) also including pre-heating.

In recent years fuel consumption of passenger vehicles has received increasing attention by customers, the automotive industry, regulatory agencies and academia. However, some areas which affect the fuel consumption have received relatively small interest. One of these areas is the total energy used for vehicle interior climate which can have a large effect on real-world fuel consumption. Although there are several methods described in the literature for analyzing fuel consumption for parts of the climate control system, especially the Air-Condition (AC) system, the total fuel consumption including the vehicle interior climate has often been ignored, both in complete vehicle testing and simulation. The purpose of this research was to develop a model that predicts the total energy use for the vehicle interior climate. To predict the total energy use the model included sub models of the passenger compartment, the air-handling unit, the AC, the engine cooling system and the engine.

Frontal Severe Partial Overlap Collisions (SPOC) also called small overlap crashes pose special challenges with respect to structural design as well as occupant protection. In the early 1990s, the SPOC test method was developed addressing 20-40% overlap against a fixed rigid barrier with initial velocities up to 65 km/h. The knowledge gained has been used in the design of Volvo vehicles since then. Important design principles include front side members orientated along the wheel envelopes together with a strong support structure utilizing a space frame principle with beams loaded mainly in tension and compression. This novel setup was first introduced in the 850-model in 1991 and has been refined and patented (2001) in later Volvo front structures. Among the design principles are multiple front side members on each side, helping energy absorption efficiency and robustness.

To improve fuel efficiency and facilitate handling of the vehicle in a dense city environment, it should be as small as possible given its intended application. This downsizing trend impacts the size of the engine bay, where the air filter box has to be packed in a reduced space, still without increased pressure drop, reduced load capacity nor lower filtering efficiency. Due to its flexibility and reduced cost, CFD simulations play an important role in the optimization process of the filter design. Even though the air-flow through the filter box changes as the dust load increases, the current modeling framework seldom account for such time dependence. Volvo Car Corporation presents an industrial affordable model to solve the time-dependent dust load on filter elements and calculate the corresponding flow behavior over the life time of the air filter box.

The new SULEV legislation for passenger cars with gasoline powered engines, which will be introduced with the California LEV II program in the year 2003, requires a further development of the exhaust aftertreatment system. Three fundamentally different system approaches, each with very high efficiency in reducing cold start hydrocarbons, will be discussed in this paper. Vehicle test results will be presented to illustrate the potential of the respective systems towards the SULEV requirements. Durability aspects are also considered since an increased durability of 120 000 and even 150 000 miles is imposed by the legislation.

In recent years fuel consumption of passenger vehicles has received increasing attention by customers, the automotive industry, regulatory agencies and academia. However, some areas which affect the fuel consumption have received relatively small interest. One of these areas is the total energy used for vehicle interior climate which can have a large effect on real-world fuel consumption. Realistic combinations of energy saving measures were evaluated regarding the total energy use for vehicle interior climate using a one dimensional (1D) simulation model. The 1D simulation model included sub models of the passenger compartment, the air-handling unit, the Air Conditioning (AC) system, engine and engine cooling system. A test cycle representative for real-world conditions was developed. The test cycle included tests in cold, intermediate and warm conditions and the results were weighted with the estimated use in each condition.

Future demands for improvements in the fuel economy of gasoline passenger car engines will require the development and implementation of advanced combustion strategies, to replace, or combine with the conventional spark ignition strategy. One possible strategy is homogeneous charge compression ignition (HCCI) achieved using negative valve overlap (NVO). However, several issues need to be addressed before this combustion strategy can be fully implemented in a production vehicle, one being to increase the upper load limit. One constraint at high loads is the combustion becoming too rapid, leading to excessive pressure-rise rates and large pressure fluctuations (ringing), causing noise. In this work, efforts were made to reduce these pressure fluctuations by using a late injection during the later part of the compression. A more appropriate acronym than HCCI for such combustion is SCCI (Stratified Charge Compression Ignition).

Several of the exterior noise sources existing around a vehicle can cause airborne noise issues at relatively low frequencies. SEA, traditionally used for airborne sound issues is not suitable for the frequency range of interest. Finite Element analysis has been used. Handling of the non-reflecting condition on the outer boundary of the exterior cavity is an issue. Recently, advances have been made in several commercially available codes, which made the analysis practical. Including the poro-elastic material model for foam-based carpets is also becoming practically possible. The purpose of the current study is to investigate the practical applications of those new developments against test data, and to estimate the feasibility of using these procedures in the vehicle development projects. Measurements were carried out in a new semi-anechoic chamber at Volvo Cars. These measurements involved 3 body objects - a Body-in-Blue (BIB) sedan, a Complete Vehicle (CV) sedan and a CV wagon.

Even though substantial improvements have been made for the lean NOx trap (LNT) catalyst in recent years, the durability still remains problematic because of the sulfur poisoning and sintering of the precious metals at high operating temperatures. Hence, commercial LNT catalysts were aged and tested in order to investigate their performance and activity degradation compared to the fresh catalyst, and establish a proper correlation between the aging methods used. The target of this study is to provide useful information for regeneration strategies and optimize the catalyst management for better performance and durability. With this goal in mind, two different aging procedures were implemented in this investigation. A catalyst was vehicle-aged in the vehicle chassis dynamometer for 100000 km, thus exposed to real conditions. Whereas, an accelerated aging method was used by subjecting a fresh LNT catalyst at 800 °C for 24 hours in an oven under controlled conditions.

With the growing concern about the potential dangers with rear facing child seats placed in the front seat of passenger airbag equipped cars, various systems are being considered for deactivation of the airbag. To increase the awareness of and confidence in these proposed systems, information displays were developed for the purpose of telling the status of the passenger airbag system and to warn when necessary. A study of the effectiveness, understanding and acceptance of a selection of such information displays was jointly undertaken by Volvo Car Corporation, SAAB Automobile AB and the Swedish National Road and Transport Research Institute. Respondents of various age and demographic composition, parents and grand parents of small children, were exposed to six different sets of information displays and were asked to interpret them and also rank which information displays that would most clearly convey the message.

With alternative fuels having moved more into market in light of their reduction of emissions of CO2 and other air pollutants, the spark ignited internal combustion engine design has only been affected to small extent. The development of combustion engines running on natural gas or Biogas have been focused to maintain driveability on gasoline, creating a multi fuel platform which does not fully utilise the alternative fuels’ potential. However, optimising these concepts on a fundamental level for gas operation shows a great potential to increase the level of utilisation and effectiveness of the engine and thereby meeting the emissions legislation. The project described in this paper has focused on optimising a combustion concept for CNG combustion on a single cylinder research engine. The ICE’s efficiency at full load and the fuels characteristics, including its knock resistance, is of primary interest - together with part load performance and overall fuel consumption.

The demand for more energy efficient vehicles is driven by environmental considerations and alternative engine technology. In order to reduce fuel consumption on future vehicles the power needed to propel the car has to be lowered. Hence, considerable efforts are needed to improve the aerodynamics. For a modern vehicle the potential for further improvements on drag is mainly to be found in the underbody region, Howell (1991). This requires more knowledge of the underbody flow and the flow around the wheels. In the present work the flow in the underbody region has been studied using a combination of experiments and calculations to obtain a more comprehensive database. The model chosen for this work was the so called ASMO model from Daimler Benz, which is a well known geometry that is available for the public on the internet. A simple model was preferred since the goal was to study the basic mechanisms behind drag generated by the underbody flow.

Passenger cars equipped with diesel engines will meet challenging emission legislation for the coming decade, with introduction of Euro6 and Euro7, which comprises reduced NOX emissions and possibly new driving cycles including off-cycle limits. The technology measures to meet these legislative limits comprise a broad spectrum of engine and aftertreatment, i.e., engine measures such as improved fuel injection with respect to mass and timing, improved exhaust gas recirculation, improved warm-up and reduced friction, as well as aftertreatment measures such as selective catalytic reduction and lean NOX trap in combination with diesel particulate filter, and the thereby associated engine control. The resulting technology matrix is therefore large, and calls for a multidisciplinary simulation approach for appropriate selection and optimization of technology and control with the objectives and constraints of emissions, fuel consumption, performance and cost.

In May 1998 Volvo launched its most exclusive car model so far, the Volvo S80, which is aimed to compete with upper luxury segment products. The car is produced in the new production facility in the Torslanda plant in Sweden. Among the more highlighted features were a transversely mounted in-line six cylinder engine with a specially designed gearbox, electronic multiplex technology with 18 computers in the network, and safety features like stability and traction control (STC), front seats with integrated antiwhiplash system (WHIPS) and inflatable curtain (IC) for improved side impact protection. To fulfill the product's high demands on safety, quality and environmental care, the design, materials selection and assembly of the car body with high precision had to be very carefully engineered. As in previous product-/process development a holistic and concurrent engineering approach was necessary.