Search Results

The Stiller-Smith mechanism is a new mechanism for the translation of linear motion into rotary motion, and has been considered as an alternative to the conventional slider-crank mechanism in the design of internal combustion engines and piston compressors. Piston motion differs between the two mechanisms, being perfectly sinusoidal for the Stiller-Smith case. Plots of dimensionless volume and volume rate-change are presented for one engine cycle. It is argued that the different motion is important when considering rate-based processes such as heat transfer to a cylinder wall and chemical kinetics during combustion. This paper also addresses the fact that a Stiller-Smith engine will be easier to configure for adiabatic operation, with many attendant benefits.

The Stiller-Smith Engine employs a non-standard gear train and as such requires a closer examination of the design and sizing of the gears. To accomplish this the motion of the Stiller-Smith gear train -will be compared to more familiar arrangements. The results of a kinematic and dynamic analysis will introduce the irregular forces that the gears are subjected to. The “floating” or “trammel” gear will be examined more closely, first stochastically and then with finite element analysis. This will pinpoint high stress concentrations on the gear and where they occur during the engine cycle, The configuration considered will be one with: an output shaft, negligible idler gear forces, and floating gear pins that are part of the connecting rods rather than the floating gear. Various loading techniques will be discussed with possible ramifications of each.

New high-tech materials which are anticipated to revolutionize the internal combustion engine are being created everyday. However, their actual utilization in existing engines has encountered numerous stumbling blocks. High piston sidewall forces and thermal stresses are some of the problems of primary concern. The Stiller-Smith Engine should provide an environment more conducive to the use of some of these materials. Absent from the Stiller-Smith Engine is a crankshaft, and thus a very different motion is observed. Since all parts in the Stiller-Smith Engine move in either linear or rotary fashion it is simple to balance. Additionally the use of linear connecting rod bearings changes the location of the sidewall forces thus providing an isolated combustion chamber more tolerant to brittle materials and potential adiabatic designs. Presented herein is the development of this new engine environment, from conceptualization to an outline of present and future research.

The Rand-Cam engine is a positive displacement machine, operating on a four stroke cycle, which consists of a rotor with multiple axial vanes forming combustion chambers as the rotor and vanes rotate in a cam shaped housing. The cam housing, consisting of two “half-housings” or stators, contains a toroidal trough of varying depth machined into each stator. The two stators are phased so that the shallowest point on one trough corresponds to the deepest on the other. A set of six vanes, able to move axially through machined holes in the rotor, traverses the troughs creating six captured zones per side. These zones vary in volume with rotor rotation. Since each trough has two deep sections and two shallow sections with ramps in between, full four stroke operation is obtained between each pair of vanes in each trough, corresponding to twelve power “strokes” per revolution.

This paper describes a Radio Frequency (RF) plasma ignitor concept intended for application to internal combustion engines. This system features a high Q quarter-wave coaxial cavity resonator, of simple construction, serving as a tuning element in the RF power supply, a voltage magnifier, and a discharge device attached to the combustion chamber. The resonator is filled with a dielectric and open at the discharge end. The center conductor is terminated with a revolute solid capacitive electrode which concentrates the associated electric field. This non-uniform electric field within the air/fuel mixture creates a corona discharge plasma which is excited at the RF operating frequency and the resulting ionic species recombine to initiate combustion. The RF excitation, relative to DC, reduces breakdown voltage and electrode degradation.

The mechanism considered here, combines the functions of a planetary gear train and a continuously variable transmission (CVT) system, through a circulating power control unit, which results by connecting the sun-gear shaft and the ring-gear rotation through a variable pitch pulley system. The mechanism is simple and does not require clutches for its operation. Three basic configurations are presented, two of them produce a power feedback effect and a third one produces a power split forward, without a “geared neutral” condition. Parametric analysis is carried out in relation to the circulating power split feature in order to to assist in the design of an optimum configuration for light-weight applications. A parametric approach is used to generate a model that can be used to perform parametric sensitivity analysis.

Natural Gas engines are viewed as an alternative to diesel power in the quest to reduce heavy duty vehicle emissions in polluted urban areas. In particular, it is acknowledged that natural gas has the potential to reduce the inventory of particulate matter, and this has encouraged the use of natural gas engines in transit bus applications. Extensive data on natural gas and diesel bus emissions have been gathered using two Transportable Heavy Duty Vehicle Emissions Testing Laboratories, that employ chassis dynamometers to simulate bus inertia and road load. Most of the natural gas buses tested prior to 1997 were powered by Cummins L-10 engines, which were lean-burn and employed a mechanical mixer for fuel introduction. The Central Business District (CBD) cycle was used as the test schedule.

A novel engine concept, currently under study, addresses many of the problems commonly associated with conventional internal combustion engines. In its simplest form the novel engine consists of a single crankshaft operating both a piston compressor and a piston expander which are connected by a continuous flame combustion chamber. One might regard this as a Brayton piston engine which is similar to a previous engine investigated by Warren. Also, due to the use of piston cylinders as the compression and expansion devices, this engine varies little mechanically from current engine technology thus allowing for easy implementation. The main improvement from conventional engine design is that the expansion cylinder can have a larger displacement than that of the compression cylinder. This allows more power to be extracted by lowering the loss due to blowdown and this will increase the thermal efficiency.

In this paper, a new method for the hydro-dynamic analysis of a sliding cylinder in a fully lubricated parallel track is presented. The method is an extension of Booker's “Mobility Method” (developed for cylindrical journal bearings) to the case of sliding cylinders, in which the clearance between the track and the cylinder, the viscosity of the lubricant, the radius and length of the pin, the sliding velocity and the applied transverse load determine the hydrodynamic behavior of the cylinder. In the Rand Cam™ Engine [1]*, the axicycloidal motion of vanes is driven by a rotor and a cylindrical cam, and one of the alternative designs to provide this function is based on a cylindrical pin sliding within a track which follows the profile of the motion of the main cams of the engine. This function is very important for the engine, since it separates the load bearing function from the sealing function left to the apex-like seals.

A set of experiments were conducted to evaluate the performance differences between a Low Heat Rejection Engine (LHRE) which is ceramic-insulated and a conventional baseline metal diesel engine which is water-cooled. Both engines were single cylinder, direct injection, and turbocharged. The objective of the study was to investigate the rate of heat release of these engines so that performance improvement procedures could be obtained. In this paper, the difference of the ignition delay between the two engines was determined. Two methods for improving the combustion process of the LHRE were studied: use of mixture fuels and increase the fuel injection rate. Both methods proved effective and reduced the fuel consumption rate of the LHRE.

With the implementation of a closed loop fuel control system, operation of lean-burn natural gas engines can be optimized in terms of reducing emissions while maximizing efficiency. Such a system would compensate for variations in fuel composition, but also would correct for variations in volumetric efficiency due to immediate engine history and long-term engine component wear. Present day engine controllers perform well when they are operated with the same gas composition for which they were calibrated, but because fuel composition varies geographically as well as seasonally, some method of compensation is required. A closed loop control system on a medium-duty lean-burn engine will enhance performance by maintaining the desired air-fuel ratio to eliminate any unwanted rich or lean excursions (relative to the desired air-fuel ratio) that produce excess engine-out emissions. Such a system can also guard against internal engine damage due to overheating and/or engine knock.

Specific aspects of a study aimed at developing a microwave assisted regeneration system for diesel particulate traps are discussed. Results from thermal and microwave characteristic studies carried out in the initial phase of the study are reported. The critical parameters that need to be optimized, for achieving controlled regeneration, are microwave preheating time period, regenerative air supply, regenerative air temperature, and soot deposition. Using a 1000 W magnetron, power measurements were made to select the best waveguide configuration for optimized transmission. A six cylinder naturally aspirated, indirect injection diesel engine was retrofitted with a customized exhaust system that included a Corning EX80 (5.66″ × 6.00″) type ceramic particulate trap. An automated exhaust bypass system enabled trap loading and subsequent regeneration with a customized microwave regeneration system. The paper discusses the salient details of both on-line and off-line regeneration setups.

West Virginia University (WVU) is a participant in EcoCAR - The NeXt Challenge, an Advanced Vehicle Technology Competition sponsored by the U.S. Department of Energy, and General Motors Corporation. During the first year of the competition, the goal of the WVU EcoEvolution Team was to design a novel hybrid-electric powertrain for a 2009 Saturn Vue to increase pump-to-wheels fuel economy, reduce criteria tailpipe emissions and well-to-wheels greenhouse gas emissions (GHG) while maintaining or improving performance and utility. To this end, WVU designed a 2-Mode split-parallel diesel-electric hybrid system. Key elements of the hybrid powertrain include a General Motors 1.3L SDE Turbo Diesel engine, a General Motors Corporation 2-Mode electrically variable transmission (EVT) and an A123 Systems Lithium-Ion battery system. The engine will be fueled on a blend of 20% soy-derived biodiesel and 80% petroleum-derived ultra-low sulfur diesel fuel (B20).

The new General Motors 2-mode hybrid transmission for front-wheel-drive vehicles has been incorporated into a 2009 Saturn Vue by the West Virginia University EcoCAR team. The 2-mode hybrid transmission can operate in either one of two electrically variable transmission modes or four fixed gear modes although only the electrically variable modes were explored in this paper. Other major power train components include a GM 1.3L SDE turbo diesel engine fueled with B20 biodiesel and an A123 Systems 12.9 kWh lithium-ion battery system. Two additional vehicle controllers were integrated for tailpipe emission control, CAN message integration, and power train hybridization control. Control laws for producing maximum fuel efficiency were implemented and include such features as engine auto-stop, regenerative braking and optimized engine operation. The engine operating range is confined to a high efficiency area that improves the overall combined engine and electric motor efficiency.

Diesel soot interacts with the engine oil and leads to wear of engine parts. Engine oil additives play a crucial role in preventing wear by forming the anti-wear film between the wearing surfaces. The current study was aimed at investigating the interactions between engine soot and oil properties in order to develop high performance oils for diesel engines equipped with exhaust gas re-circulation (EGR). The effect of soot contaminated oil on wear of engine components was examined using a statistically designed experiment. To quantitatively analyze and simulate the extent of wear a three-body wear machine was designed and developed. The qualitative wear analysis was performed by examining the wear scars on an AISI 52100 stainless steel ball worn in the presence of oil test samples on a ball-on-flat disc setup. The three oil properties studied were base stock, dispersant level and zinc dithiophosphate level.

The emissions reduction of Fischer-Tropsch (FT) diesel fuel has been demonstrated in several recent publications in both laboratory engine testing and in-use vehicle testing. Reduced emission levels have been attributed to several chemical and physical characteristics of the FT fuels including reduced density, ultra-low sulfur levels, low aromatic content and high cetane rating. Some of the effects of these attributes on the combustion characteristics in diesel engines have only recently been documented. In this study, a Ricardo Proteous, single-cylinder, 4-stroke DI engine is instrumented for in-cylinder pressure measurements. The engine was run at several steady engine states at multiple timing conditions using both federal low sulfur and natural gas derived FT fuels. The emissions and performance data for each fuel at each steady state operating conditions were compared.

The need for a cleaner and less expensive alternative energy source to conventional petroleum fuels for powering the transportation sector has gained increasing attention during the past decade. Special attention has been directed towards natural gas (NG) which has proven to be a viable option due to its clean-burning properties, reduced cost and abundant availability, and therefore, lead to a steady increase in the worldwide vehicle population operated with NG. The heavy-duty vehicle sector has seen the introduction of natural gas first in larger, locally operated fleets, such as transit buses or refuse-haulers. However, with increasing expansion of the NG distribution network more drayage and long-haul fleets are beginning to adopt natural gas as a fuel.

The Rand Cam engine is a novel design which avoids the use of pistons in favor of a cavity of varying size and shape. A set of vanes protrudes from a rotor into a circular trough in a stator. The vanes seal to the walls and base of the trough, which is of varying depth, and progress around the trough with rotation of the rotor. These vanes therefore pass through the rotor and are constrained to move parallel to the rotational axis. Intake and exhaust processes occur through ports in the stator wall which are revealed by the passing vanes. Advantages of the basic design include an absence of valves, reduction in reciprocating masses, presence of an integral flywheel in the rotor and strong fluid movement akin a swirl induced by the relative velocity between the rotor and stator.

Corona discharge from a RF quarter wave coaxial cavity resonator is considered as a plasma ignition source for spark ignited (SI) internal combustion (IC) engines. The gaseous discharge processes associated with this device are analyzed using principles of gas kinetics and gaseous electronics, with assumed values for the electric field strength. Corona discharge occurs when the electric field shaped and concentrated by a single electrode exceeds the breakdown potential of the surrounding gas. Ambient electrons, naturally present due to ionizing radiation, drift in the direction of the externally applied field, gaining energy while undergoing elastic collisions with neutral molecules. After gaining sufficient energy they dissociate, excite, or ionize the neutral particles through inelastic collision, creating additional electrons. This process leads to avalanche electrical breakdown of the gas within about 10-8 sec.

A mathematical model has been developed to transfer Chassis Dynamometer (CD) test cycles for heavy duty vehicles to the equivalent Engine Dynamometer (ED) test cycles. The model assumed a generalized drivetrain layout, and a variable drive line efficiency. An interactive computer code was written to represent the mathematical model for different drivetrain systems. Several CD test cycles were used to obtain equivalent ED test cycles for a sample based upon an urban bus equipped with an automatic transmission. Results showed the possibility of simulating CD test cycles with equivalent ED test cycles for heavy-duty urban buses under certain assumptions.