Search Results

In a consortium of European industrial partners and research institutes, a combination of industrial development and scientific research was organised. The objective was to improve the catalytic NOx conversion for lean burn cars and heavy-duty trucks, taking into account boundary conditions for the fuel consumption. The project lasted for three years. During this period parallel research was conducted in research areas ranging from basic research based on a theoretical approach to full scale emission system development. NOx storage catalysts became a central part of the project. Catalysts were evaluated with respect to resistance towards sulphur poisoning. It was concluded that very low sulphur fuel is a necessity for efficient use of NOx trap technology. Additionally, attempts were made to develop methods for reactivating poisoned catalysts. Methods for short distance mixing were developed for the addition of reducing agent.

The effect of changing catalyst precious metal ratios and loadings on close coupled catalytic converter efficiencies has been studied. The three precious metals were platinum, palladium and rhodium. The specific matrix used for the development of response surface models is a central composite design and provides the capability of visually optimising the precious metal loadings. Catalysts were evaluated using perturbed scans. lightoff curves from the dynamometer aged, and vehicle emission tests. These scans show percent conversion efficiencies of the three legislated gases; HC, CO and NOx, over a range of Air Fuel Ratios (λ). Whilst lean and rich lightoff curves provide indications of conversion efficiencies at varying temperatures. Prior to testing the catalysts were aged, using an accelerated dynamometer ageing process, to 80K simulated kilometres. The catalysts were then fitted to a vehicle and chassis roll emission tests conducted.

This paper explores the feasibility of using in-cylinder pressure-based variables to predict gaseous exhaust emissions levels from a Navistar T444 direct injection diesel engine through the use of neural networks. The networks were trained using in-cylinder pressure derived variables generated at steady state conditions over a wide speed and load test matrix. The networks were then validated on previously “unseen” real-time data obtained from the Federal Test Procedure cycle through the use of a high speed digital signal processor data acquisition system. Once fully trained, the DSP-based system developed in this work allows the real-time prediction of NOX and CO2 emissions from this engine on a cycle-by-cycle basis without requiring emissions measurement.

Process planning, whether generative or variant, can be used effectively as through the incorporation of computer aided tools that enhance the evaluator impact of the dialogue between the design and manufacturing functions. Expert systems and algorithms are inherently incorporated into the software tools used herein. This paper examines the materials related implications that influence design for manufacturing issues. Generative process planning software tools are utilized to analyze the sensitivity of the effectiveness of the process plans with respect to changing attributes of material properties. The shift that occurs with respect to cost and production rates of process plans with respect to variations in specific material properties are explored. The research will be analyzing the effect of changes in material properties with respect to the design of a specific product that is prismatic and is produced exclusively by machining processes.

The Federal Test Procedure (FTP) for heavy-duty engines requires the use of a full-flow tunnel based constant volume sampler (CVS) which is costly to build and maintain, and requires a large workspace. A portable micro-dilution system that could be used for measuring on-board, in use emissions from heavy duty vehicles would be an inexpensive alternative compared to a full-flow CVS tunnel, as well as requiring significantly less workspace. This paper evaluates such a portable particulate matter measuring system. This micro-dilution tunnel operates on the same principle as a full-flow tunnel, however dilution ratios can be more easily controlled with the micro dilution system. The dilution ratios for the micro-dilution system were maintained at least four to one, as per ISO 8178 requirements, by measuring the mass flow rates of the dilution air and dilute exhaust.

Most transient heavy duty diesel emissions data in the USA have been acquired using the Federal Test Procedure (FTP), a heavy-duty diesel engine transient test schedule described in the US Code of Federal Regulations. The FTP includes both urban and freeway operation and does not provide data separated by driving mode (such as rural, urban, freeway). Recently, a four-mode engine test schedule was created for use in the Advanced Collaborative Emission Study (ACES), and was demonstrated on a 2004 engine equipped with cooled Exhaust Gas Recirculation (EGR). In the present work, the authors examined emissions using these ACES modes (Creep, Cruise, Transient and High-speed Cruise) and the FTP from a Detroit Diesel Corporation (DDC) Series 60 1992 12.7 liter pre-EGR engine. The engine emissions were measured using full exhaust dilution, continuous measurement of gaseous species, and filter-based Particulate Matter (PM) measurement.

A test method, based on parallel sample testing with exhaust fuel injection and certain test procedures, has been developed for diesel lean-NOx catalyst evaluation purposes. The results of the verification tests show uniform distribution of both the exhaust gas and the injected fuel, and a high degree of fuel evaporation. Test procedures are discussed from several points of view. The test method offers a precise and efficient way of testing lean-NOx catalysts on heavy duty diesel engines.

The implementations of the Tier 2 and LEVII emission levels require fast catalyst light-off and fast closed loop control through high-speed engine management. The paper describes the development of innovative catalyst designs. During the development thermal and mechanical boundary conditions were collected and component tests conducted on test rigs to identify the emission and durability performance. The products were evaluated on a Super Imposed Test Setup (SIT) where thermal and mechanical loads are applied to the test piece simultanously and results are compared to accelerated vehicle power train endurance runs. The newly developed light-off catalyst with Perforated Foil Technology (PE) showed superior emission light-off characteristic and robustness.

The Federal Test Procedure (FTP) for heavy-duty engines requires the use of a full-flow tunnel based constant volume sampler (CVS). These are costly to build and maintain, and require a large workspace. A small portable micro-dilution system that could be used on-board, for measuring emissions of in-use, heavy-duty vehicles would be an inexpensive alternative. This paper presents the rationale behind the design of such a portable particulate matter measuring system. The presented micro-dilution tunnel operates on the same principle as a full-flow tunnel, however given the reduced size dilution ratios can be more easily controlled with the micro dilution system. The design targets dilution ratios of at least four to one, in accordance with the ISO 8178 requirements. The unique features of the micro-dilution system are the use of only a single pump and a porous sintered stainless steel tube for mixing dilution air and raw exhaust sample.

Gasoline-powered vehicles compose the vast majority of all light-duty vehicles in the United States. Improving fuel economy is currently a topic of great interest due to the rapid rise in gasoline costs as well as new fuel-economy and greenhouse-gas emissions standards. The Chevrolet Silverado is currently one of the top selling trucks in the U.S. and has been previously modeled using the commercial finite element code LS-DYNA by the National Crash Analysis Center (NCAC). This state-of the art model was employed to examine alternative weight saving configurations using material alternatives and replacement of traditional steel with composite panels. Detailed mass distribution analysis demonstrated the chassis assembly to be an ideal candidate for weight reduction and was redesigned using Aluminum 7075-T6 Alloy and Magnesium Alloy HM41A-F.

Enhancements in the thermal stability of three-way catalysts have been achieved by: 1) developing improved methods for the incorporation of ceria into catalyst formulations and 2) identifying a proprietary stabilizer which reduces the rate of ceria sintering at high temperature. Improvements in thermal stability are demonstrated by comparing the FTP and engine dynamometer performance of new formulations with a standard formulation after aging on several high temperature engine dynamometer cycles.

A work-based window method has been developed to calculate in-use brake-specific oxides of nitrogen (NOx) emissions for all engine speeds and engine loads. During an in-use test, engine speed and engine torque are read from the engine's electronic control unit, and along with time, are used to determine instantaneous engine power. Instantaneous work is calculated using this power and the time differential in the data collection. Work is then summed until the target amount of work is accumulated. The emissions levels are then calculated for that window of work. It was determined that a work window equal to the theoretical Federal Test Procedure (FTP) cycle work best provides a means of comparison to the FTP certification standard. Also, a failure criterion has been established based on the average amount of power generated in the work window and the amount of time required to achieve the target work window to determine if a particular work window is valid.