Search Results

Controlled Auto-Ignition (CAI) combustion, also known as Homogeneous Charge Compression Ignition (HCCI), has the potential to simultaneously reduce the fuel consumption and nitrogen oxides emissions of gasoline engines. However, narrow operating region in loads and speeds is one of the challenges for the commercial application of CAI combustion to gasoline engines. Therefore, the extension of loads and speeds is an important prerequisite for the commercial application of CAI combustion. The effect of intake charge boosting, charge stratification and spark-assisted ignition on the operating range in CAI mode was reviewed. Stratified flame ignited (SFI) hybrid combustion is one form to achieve CAI combustion under the conditions of highly diluted mixture caused by the flame in the stratified mixture with the help of spark plug.

Poppet-valve two-stroke gasoline engines can increase the specific power of their four-stroke counterparts with the same displacement and hence decrease fuel consumption. However, knock may occur at high loads. Therefore, the combustion with stratified lean mixture was proposed to decrease knock tendency and improve combustion stability in a poppet-valve two-stroke direct injection gasoline engine. The effect of intake pressure and split injection on fuel distribution, combustion and knock intensity in lean mixture conditions at high loads was simulated with a three-dimensional computational fluid dynamic software. Simulation results show that with the increase of intake pressure, the average fuel-air equivalent ratio in the cylinder decreases when the second injection ratio was fixed at 70% at a given amount of fuel in a cycle.

Controlled Auto-Ignition (CAI), also known as Homogeneous Charge Compression Ignition (HCCI), can improve the fuel economy of gasoline engines and simultaneously achieve ultra-low NOx emissions. However, the difficulty in combustion phasing control and violent combustion at high loads limit the commercial application of CAI combustion. To overcome these problems, stratified mixture, which is rich around the central spark plug and lean around the cylinder wall, is formed through port fuel injection and direct injection of gasoline. In this condition, rich mixture is consumed by flame propagation after spark ignition, while the unburned lean mixture auto-ignites due to the increased in-cylinder temperature during flame propagation, i.e., stratified flame ignited (SFI) hybrid combustion.

Two identical helical ports and two identical directed ports were arranged into four different kinds of port combinations: helical and helical, helical and directed, directed and directed, directed and helical. Each port can rotate freely around its valve axis. The swirl ratio and the flow coefficient for each combination of intake ports were tested on a steady flow rig when both ports were positioned in different orientations around its valve axis. Two parameters, the loss rate of mean flow coefficient and the loss rate of angular momentum, were defined to describe the degree of interference between the flows discharging from the two adjacent intake valves. Velocity distribution in the vicinity and circumference of the intake valves was measured using Hot Wire Anemometer to further study the intake flow interference for different port combinations.

The effect of the Swirl Control Valve (SCV) on the in-cylinder flow characteristics was studied using LDA measurement in a single cylinder four-valve spark ignition engine with a SCV. Mean velocity, root-mean-square (rms) velocity fluctuation, and frequency structure of the velocity fluctuation were analyzed to illustrate flow features under the SCV open and closed conditions. The results show that when the SCV is open, large-scale flow structure in the cylinder is mainly tumble vortex, which will distort and break up during the late stage of the compression stroke. The rms velocity fluctuation increases during the compression process and reaches its maximum at certain crank angle before TDC. Larger scale eddies and lower frequency structures in the flow field become more near the end of compression process due to breakup of the tumble. The rms velocity fluctuation in the combustion chamber is roughly uniform at the end of the compression process.

Although supercharged system has been widely employed in downsized engines, the effect of supercharging on the intake flow characteristics remains inadequately understood. Therefore, it is worthwhile to investigate intake flow characteristics under high intake pressure. In this study, the supercharged intake flow is studied by experiment using steady flow test bench with supercharged system and transient flow simulation. For the steady flow condition, gas compressibility effect is found to significantly affect the flow coefficient (Cf), as Cf decreases with increasing intake pressure drop, if the compressibility effect is neglected in calculation by the typical evaluation method; while Cf has no significant change if the compressibility effect is included. Compared with the two methods, the deviation of the theoretical intake velocity and the density of the intake flow is the reason for Cf calculation error.