Search Results

A zero-dimension model of spray development and particulate emissions for direct-injection combustion was developed. The model describes the major characteristics of the injection plume including: spray angle, liquid penetration, lift-off length, and temperatures of regions within the spray. The model also predicts particulate mass output over a span of combustion cycles, as well as a particulate mass-history over a single combustion event. The model was developed by applying established conceptual models for direct injection combustion to numerical relations, to develop a mathematical description of events. The model was developed in a Matlab Simulink environment to promote modularity and ease of use.

Laser Doppler velocimetry has been used to measure velocity and turbulence intensity profiles in the wall boundary layer of a spark-ignited homogeneous-charge research engine. By using a toroidal contoured engine head it was possible to bring the laser probe volume to within 60 μm of the wall. Two different levels of engine swirl were used to vary the flow Reynolds number. For the high swirl case under motored operation the boundary layer thickness was less than 200 μm, and the turbulence intensity increased as the wall was approached. With low swirl the 700-1000 μm thick boundary layer had a velocity profile that was nearly laminar in shape, and there was no increase in turbulence intensity near the wall. When the engine was fired the boundary layer thickness increased for both levels of swirl.

The present study proposes the use of a MLP neural network to model the relationship between the engine crankshaft speed and parameters derived from the in-cylinder pressure cycle. This allows to have an indirect measure of cylinder pressure permitting a real time evaluation of combustion quality. The structure of the model and the training procedure is outlined in the paper. The application of the model is demonstrated on a single-cylinder engine with data from a wide range of speed and load. Results confirm that a good estimation of combustion pressure parameters can be obtained by means of a suitable processing of crankshaft speed signal.

Electronic engine controls based on non-intrusive diagnostics can significantly help in complying with the stricter and stricter regulations on pollutants emissions and fuel consumption. The aim of this paper is the use of a low-cost linear capacitive accelerometer placed on the engine block for non-intrusive diagnosis of combustion process in spark ignition engines. In particular, good correspondences between the engine block vibrations and the combustion pressure signal were obtained. The angular position of pressure peak evaluated by accelerometer data can be used in a closed-loop control system for real time control of spark advance.

The flow in engine turbocharger compressors and turbines is highly unsteady in nature, as it responds to the intake and exhaust manifolds of the internal combustion engine. The optimization of the turbocharger system is therefore a very difficult task, since the devices operate at off-design conditions for most of the engine cycle. Experimental studies allow for improving the understanding on the behavior of the engine components, in particular when tests are performed under real engine operating conditions; however, the experimental tests can be more efficient if they are combined with theoretical simulation tools, which help to select significant engine operating conditions. In this paper, experimental investigations were performed on a flexible component test rig (expressly suited to perform tests on automotive turbochargers) at ICE Laboratory of the University of Genoa (ICEG-DIMSET).

A detailed thermodynamic analysis was performed to demonstrate the fundamental efficiency advantage of an opposed-piston two-stroke engine over a standard four-stroke engine. Three engine configurations were considered: a baseline six-cylinder four-stroke engine, a hypothetical three-cylinder opposed-piston four-stroke engine, and a three-cylinder opposed-piston two-stroke engine. The bore and stroke per piston were held constant for all engine configurations to minimize any potential differences in friction. The closed-cycle performance of the engine configurations were compared using a custom analysis tool that allowed the sources of thermal efficiency differences to be identified and quantified.

The paper describes the results of a parallel 1D thermo-fluid dynamic simulation and experimental investigation of a DI turbocharged Diesel engine. The attention has been focused on the overall engine performances (air flow, torque, power, fuel consumption) as well as on the emissions (NO and particulate) along the after-treatment system, which presents a particulate filter. The 1D research code GASDYN for the simulation of the whole engine system has been enhanced by the introduction of a multi-zone quasi-dimensional combustion model for direct injection Diesel engines. The effect of multiple injections is taken into account (pilot and main injection). The prediction of NO and soot has been carried out respectively by means of a super-extended Zeldovich mechanism and by the Hiroyasu kinetic approach.

Ignition delay in diesel engine combustion comprehends both a chemical and a physical amount, the first depending on fuel composition and charge temperature and pressure, the last resulting of time needed for the fuel to atomize, vaporize and mix with air. Control of this parameter, which is mandatory to weight the relative amount of premixed to diffusive stage of the hydrocarbon combustion, is here considered. Experimental measurements of flame intensity spectra obtained by in situ measurements on an optically accessible test device show the presence of peaks corresponding to radicals as OH and CH appearing at the pressure start of combustion. Since OH radicals result from chain branching reactions, a numerical simulation is performed based on a reduced kinetic scheme which allows to measure the branching agent concentration, and whose approximate nature is adequate to the proportion chemical aspects contribute to the overall delay.

A constant volume combustion simulation has been used to compute the ignition delays of pure fuels and binary fuel mixtures in air. Minima in the ignition delays were predicted by a comprehensive chemical kinetic mechanism for binary fuel mixtures with methane. A model has been developed to predict the occurrence of autoignition in a spark ignited engine. Experimental pressure data from a CFR engine were used in the model to simulate the temperature-pressure history of the end gas and to determine the time when autoignition occurred. Comprehensive chemical kinetic mechanisms were used to predict the reactions in the end gas. Methanol, methane, ethane, ethylene, propane and n-butane were used as fuels. The initial temperatures in the model were adjusted to give agreement between predicted and observed autoignition. Engine data for methane-ethane mixtures indicated a problem with the kinetic mechanism.

The paper describes the research work concerning the simulation of 1D unsteady reacting flows in s.i. engine pipe-systems, including pre-catalysts and main catalysts. The numerical model GASDYN has been developed to enable the concurrent prediction of the wave motion in the intake and exhaust ducts, the chemical composition of the gas discharged by the cylinder of a s.i. engine, the chemical and thermal behavior of catalytic converters. The effect of considering the transport of chemical species with reactions in gas phase (post-oxidation of unburned HC in the exhaust manifold) and in solid phase (conversion of pollutants in the catalyst) on the predicted wave motion is reported.

A study was performed in which the effects on the regulated emissions from a commercial small DI diesel engine were measured for different refinery-derived fuel blends. Seven different fuel blends were tested, of which two were deemed to merit more detailed evaluation. To investigate the effects of fuel properties on the combustion processes with these fuel blends, two-color pyrometry was used via optically accessible cylinderheads. Additional data were obtained with one of the fuel blends with a heavy-duty DI diesel engine. California diesel fuel was used as a baseline. The fuel blends were made by mixing the components typically found in gasoline, such as methyl tertiary-butyl ether (MTBE) and whole fluid catalytic cracking gasoline (WH-FCC). The mixing was performed on a volume basis. Cetane improver (CI) was added to maintain the same cetane number (CN) of the fuel blends as that of the baseline fuel.

Experiments were performed on a homogeneously fueled compression ignition gasoline-type engine with a high degree of intake charge preheating. It was observed that fuels that contained lower end and/or non-branched hydrocarbons (gasoline and an 87 octane primary reference fuel (PRF) blend) exhibited sensitivity to thermal conditions in the surge tanks upstream of the intake valves. The window of intake charge temperatures, measured near the intake valve, that provided acceptable combustion was shifted to lower values when the upstream surge tank gas temperatures were elevated. The same behavior, however, was not observed while using isooctane as a fuel. Gas chromatograph mass spectrometer analysis of the intake charge revealed that oxygenated species were present with PRF 87, and the abundance of the oxygenated species appeared to increase with increasing surge tank gas temperatures. No significant oxygenated species were detected when running with isooctane.

This research focused on the effects of split injection on combustion in a diesel environment. It was done in a specially designed engine-fed combustion chamber (swirl ratio of 5) with full field optical access through a quartz window. The simulated engine combustion chamber used a special backwards spraying injector (105°). The electronically controlled injector could control the size and position of it's, two injections. Both injections were through the same nozzle and it produced very rapid injections (1.5 ms) with a maximum injection pressure of 130 MPa. Experimental data included: rate of injection, injector pressure, combustion chamber dumping (NO & NOx concentrations), flame temperature, KL factor (soot concentration) combustion pressure, and rate of pressure rise. Injection rates indicate that the UCORS injection system creates very rapid injections with the ability to produce controllable split injections.

This research focused on the effects of split injection on fuel spray behavior in a diesel environment. It was done in a special designed engine-fed combustion chamber (swirl ratio of 5) with full field optical access through a quartz window. The simulated engine combustion chamber used a special backwards spraying injector (105°). The electronically controlled injector could control the size and position of it's two injections. Both injections were through the same nozzle and it produced very rapid injections (1.5 ms) with a maximum injection pressure of 130 MPa. Experimental data included: rate of injection, injector pressure, spray plume images, tip penetration, liquid and vapor fuel distributions, combustion pressure, and rate of pressure rise. From 105° forward scatter images, tip penetration was observed to be very rapid and reached a plateau at 25 mm.

To date there is no universal agreement as to the interaction between fuel type, fuel-air mixture preparation and combustion chamber flow characteristics and their effect on soot formation. A propane fueled modified conical back-mixed steady flow reactor was built in which the fuel and air could be mixed together in varying degrees and reacted in at different mixing intensities. The onset of soot and soot loading were determined qualitatively by a photomultiplier focused on the volume inside the reactor. Increasing the degree of premix from a diffusion flame to a distribution of Φmax/Φavg = 5.0 resulted in increases of 3 to 17 percent of the soot-onset equivalence ratio and decreases in soot loading down to zero. Changes in the mixing intensity from 32.5 sec−1 to 75.7 sec−1 resulted in a change in the soot-onset equivalence ratio from 1.26 to 1.52. Soot loading was found to depend on both the mixing intensity, β, and the average number of mixes per mean residence time, β/α.

In this paper, effect of intake air temperature, coolant temperature, and compression ratio on start of heat release (SOHR) in HCCI engines is investigated. The operational range with HCCI operation was determined experimentally using a CFR (Cooperative Fuels Research) engine with n-butane as the fuel. In-cylinder pressure was processed to evaluate SOHR. The effect of intake air and coolant temperature on SOHR increases as engine speed increases. In order to gain more insight into the combustion phenomena, SOHR was calculated using the theory of Livengood-Wu and compared with the experimental data. Dependence of SOHR on the equivalence ratio shows good correspondence between experiment and calculation. On the contrary, dependence on the intake air temperature and compression ratio shows poorer correspondence with predictions, especially under low engine speed. We interpret this as an indication of the importance of the active intermediate species that remain in the combustion chamber.

A single cylinder, Cummins NH, direct-injection, diesel engine has been operated in order to evaluate the effects of aromatic content and aromatic structure on diesel engine particulates. Results from three fuels are shown. The first fuel, a low sulfur Chevron diesel fuel was used as a base fuel for comparison. The other fuels consisted of the base fuel and 10% by volume of 1-2-3-4 tetrahydronaphthalene (tetralin) a single-ring aromatic and naphthalene, a double-ring aromatic. The fuels were chosen to vary aromatic content and structure while minimizing differences in boiling points and cetane number. Measurements included exhaust particulates using a mini-dilution tunnel, exhaust emissions including THC, CO2, NO/NOx, O2, injection timing, two-color radiation, soluble organic fraction, and cylinder pressure. Particulate measurements were found to be sensitive to temperature and flow conditions in the mini-dilution tunnel and exhaust system.

The DEXA Cluster consisted of three closely interlinked projects. In 2003 the DEXA Cluster concluded by demonstrating the successful development of critical technologies for Diesel exhaust particulate after-treatment, without adverse effects on NOx emissions and maintaining the fuel economy advantages of the Diesel engine well beyond the EURO IV (2000) emission standards horizon. In the present paper the most important results of the DEXA Cluster projects in the demonstration of advanced particulate control technologies, the development of a simulation toolkit for the design of diesel exhaust after-treatment systems and the development of novel particulate characterization methodologies, are presented. The motivation for the DEXA Cluster research was to increase the market competitiveness of diesel engine powertrains for passenger cars worldwide, and to accelerate the adoption of particulate control technology.

Gasoline fueled Homogeneous Charge Compression Ignition (HCCI) combustion with internal exhaust gas re-circulation using Negative Valve Overlap (NOL) was investigated by means of calculation and experiment in order to apply this technology to practical use with sufficient operating range and with acceptable emission and fuel consumption. In this paper we discuss the basic characteristics of NOL-HCCI with emphasis on the influence of intake valve timing on load range, residual gas fraction and induction air flow rate. Emission and fuel consumption under various operation conditions are also discussed. A water-cooled 250cc single cylinder engine with a direct injection system was used for this study. Three sets of valve timing were selected to investigate the effect of intake valve opening duration. Experimental results demonstrated that an engine speed of approximately 2000rpm yields an NMEP (Net Mean Effective Pressure) range from 200kPa to 400kPa.

An investigation of high speed direct injection (DI) compression ignition (CI) engine combustion fueled with gasoline (termed GDICI for Gasoline Direct-Injection Compression Ignition) in the low temperature combustion (LTC) regime is presented. As an aid to plan engine experiments at full load (16 bar IMEP, 2500 rev/min), exploration of operating conditions was first performed numerically employing a multi-dimensional CFD code, KIVA-ERC-Chemkin, that features improved sub-models and the Chemkin library. The oxidation chemistry of the fuel was calculated using a reduced mechanism for primary reference fuel combustion. Operation ranges of a light-duty diesel engine operating with GDICI combustion with constraints of combustion efficiency, noise level (pressure rise rate) and emissions were identified as functions of injection timings, exhaust gas recirculation rate and the fuel split ratio of double-pulse injections.