Refine Your Search

Topic

Search Results

Standard

Vehicle Transport Unit Load Device (ULD)

2009-12-02
CURRENT
ARP1554D
The tests are static in nature to minimize complexity and cost of required testing facilities. As far as practical, applied static loads should take into account the combined static and dynamic loads anticipated in service. It is intended that tests shall be non-destructive in nature and not result in damage unless ultimate load conditions are employed. Test equipment and methods of testing described are not meant to be restrictive. Alternate equivalent methods to accomplish the desired results may be employed. In selected cases, tests may be repeated under ultimate load conditions when required for substantiation of analytical data. If this becomes necessary, the parts deformed may be removed and replaced prior to the retest.
Standard

ULD for Aircraft Transportation of Horses

1996-06-01
HISTORICAL
ARP1621B
This SAE Aerospace Recommended Practice (ARP) defines minimum requirements for an aircraft transport ULD to transport horses properly and safely by air, to protect the horse(s) from injuries, and to protect the aircraft from corrosion created by waste spill. The ULD is designed to accommodate one horse or several. There are two types of ULDs for aircraft transportation of horses: a Type 1: The ULD is an airworthiness certified structural container, satisfying the requirements of NAS 3610 for the appropriate base size. b Type 2: The ULD consists of a self-contained stall which is positioned on a standard aircraft pallet and restrained to the pallet by means of a cargo pallet net or by straps. WARNING: It is the carrier’s responsibility to obtain airworthiness approval for a Type 2 unit using strap-restraint. Refer to 7.1 b (Documentation).
Standard

ULD for Aircraft Transportation of Horses

2017-09-11
CURRENT
ARP1621C
This SAE Aerospace Recommended Practice (ARP) defines minimum requirements for an aircraft transport ULD to transport horses properly and safely by air, to protect the horse(s) from injuries, and to protect the aircraft from corrosion created by waste spill. The ULD is designed to accommodate one horse or several. There are two types of ULDs for aircraft transportation of horses:
Standard

ULD FOR AIRCRAFT TRANSPORTATION OF HORSES

1990-08-01
HISTORICAL
ARP1621A
This SAE Aerospace Recommended Practice (ARP) defines minimum requirements for an aircraft transport ULD to transport horses properly and safely by air, to protect the horse(s) from injuries and to protect the aircraft from corrosion created by waste spill. The ULD is designed to accommodate one horse or several. There are two types of ULDs for aircraft transportation of horses: a Type 1: The ULD is an airworthiness certified structural container, satisfying the requirements of NAS 3610 for the appropriate base size. b Type 2: The ULD consists of a self-contained stall which is positioned on a standard aircraft pallet and restrained to the pallet by means of a cargo pallet net or by straps.
Standard

ULD FOR AIRCRAFT TRANSPORTATION OF HORSES

1980-03-01
HISTORICAL
ARP1621
This ARP defines minimum requirements for horse stalls necessary to maintain a structurally safe operation and protect aircraft from corrosion created by waste spills.
Standard

REQUIREMENTS FOR AIRCRAFT ON BOARD WEIGHT AND BALANCE SYSTEM

1995-06-01
HISTORICAL
ARP1409B
This SAE Aerospace Recommended Practice (ARP) establishes requirements for the function, characteristics, and installation of an aircraft On Board Weight and Balance System (OBWBS) for use on civil transport aircraft. This document is not intended to specify design methods, mechanisms, or material to accomplish the requirements set forth.
Standard

Interline Air Cargo Pallets

1985-01-01
CURRENT
AS1491A
This document establishes dimensional, structural and environmental requirements for two types of interline pallets. Type II covers NAS 3610 code sizes and Type III covers other sizes not currently included in NAS 3610.
Standard

General Requirements for Powered Drive Units (PDUs) in Aircraft Cargo Systems

2012-11-01
CURRENT
AIR4165A
This SAE Aerospace Information Report (AIR) is intended to assist the user (aircraft manufacturer/airline) in the following areas: a In the decision of whether or not to plan for the installation of a powered drive system in the cargo loading system (CLS) during the definition of the aircraft on-board cargo loading system. b If a powered drive system is decided upon, to provide general requirements to be considered during the preparation of component specifications for the powered drive units (PDUs) to be used. This provides a selection of criteria in order to obtain an optimum PDU for the application considered.
Standard

General Requirements for Powered Drive Units (PDUs) in Aircraft Cargo Systems

2019-01-16
WIP
AIR4165B
This SAE Aerospace Information Report (AIR) is intended to assist the user (aircraft manufacturer/airline) in the following areas: a. In the decision of whether or not to plan for the installation of a powered drive system in the cargo loading system (CLS) during the definition of the aircraft on-board cargo loading system. b. If a powered drive system is decided upon, to provide general requirements to be considered during the preparation of component specifications for the powered drive units (PDUs) to be used. This provides a selection of criteria in order to obtain an optimum PDU for the application considered.
Standard

General Requirements for Noncertified Cargo/Baggage Containers

2013-06-27
CURRENT
AS1677D
This SAE Aerospace Standard (AS) covers the design, fabrication, performance and operational testing requirements for lower deck containers for use in main line aircraft which do not require airworthiness certification when loaded under the conditions of compartment restraint and in accordance with the aircraft's Weight and Balance Manual and/or, where applicable according to the aircraft type's approved Weight and Balance Manual, AS36100A or NAS 3610 equivalent base plate restraint for these containers. Most sizes of containers covered by this document (base sizes K, L, P, and Q) cannot physically be loaded and latched on aircraft main deck cargo systems. Base size A and M containers can, but are not allowed on aircraft main decks, which do not accept non-certified units. Accordingly, all containers covered by this document are to be used/installed exclusively in aircraft lower deck compartments.
Standard

General Requirements for Noncertified Cargo/Baggage Containers

2002-01-31
HISTORICAL
AS1677C
This SAE Aerospace Standard (AS) covers the requirements for lower deck containers in wide body and standard body aircraft which do not require airworthiness certification under the condition of compartment restraint and/or, where applicable according to aircraft type, NAS3610 equivalent baseplate-restraint for these containers. NOTE: IATA 50/0, “Requirements for interlining of ULDs”, should also be taken into account when designing and making equipment.
Standard

GENERAL REQUIREMENTS FOR POWERED DRIVE UNITS IN AIRCRAFT CARGO SYSTEMS

1992-11-12
HISTORICAL
AIR4165
This Aerospace Information Report (AIR) serves a dual purpose. It enables the user (aircraft manufacturer/airline) to do the following: a To make a positive decision for the installation of a powered drive system in the cargo loading system during the definition of the aircraft on-board cargo loading system to be developed/procured. b To provide the user with general requirements to be taken into consideration during the preparation of component specifications for powered drive units (PDUs) to be used in aircraft cargo systems. This is to provide the author of such a component specification with a selection of criteria in order to obtain an optimum component suitable for the users’ applications.
Standard

GENERAL REQUIREMENTS FOR NONCERTIFIED LD-2, LD-4, AND LD-8 CARGO/BAGGAGE CONTAINERS

1995-06-01
HISTORICAL
AS1677B
This SAE Aerospace Standard (AS) covers the requirements for three sizes of compartment restrained lower deck containers (unit load devices) for the 767 airplane and which do not require airworthiness certification. NOTE: IATA Specification 50/0, General Technical Requirements and Serviceability limits, should also be taken into account when designing and making equipment according to this specification as certain provisions contained therein will also be applicable.
Standard

Fire Containment Cover - Design, Performance, and Testing Requirements

2013-08-06
CURRENT
AS6453
This SAE Aerospace Standard (AS), identical to ISO 14186, specifies the minimum design and performance criteria and testing methods of fire containment covers (FCCs) used either: a in those cargo compartments of civil transport aircraft where they constitute one means of complying with applicable airworthiness regulations, or b on a voluntary basis, when deemed appropriate by operators to improve fire protection in aircraft cargo compartments where airworthiness regulations do not mandate their use.
Standard

Effects of Hanging Loads (e.g., GOH) on ULD Performance

1997-11-01
HISTORICAL
AIR4359
This SAE Aerospace Information Report (AIR) provides information on the subject of Air Mode containers used for transporting “Hanging Loads” such as Garment-On-Hangers (GOH), or other roof supported cargo. It suggests considerations and recommendations for roof loaded containers to transport hanging loads efficiently and safely by air and to protect the aircraft floor and cargo system from damage due to overload conditions.
Standard

Effects of Hanging Loads (e.g., GOH) on ULD Performance

2016-05-24
CURRENT
AIR4359A
This SAE Aerospace Information Report (AIR) provides information on the subject of Air Mode containers used for transporting "Hanging Loads" such as Garment-On-Hangers (GOH), or other roof supported cargo. It suggests considerations and recommendations for roof loaded containers to transport hanging loads efficiently and safely by air and to protect the aircraft floor and cargo system from damage due to overload conditions.
Standard

Certified Containers for Lower Deck Compartments

2014-01-03
CURRENT
AS5896
This SAE Aerospace Standard (AS) covers the design, fabrication, performance, and testing requirements for general-purpose, base-restrained, containers requiring airworthiness approval for installation/use in aircraft lower deck compartments. See 10.1 and 10.2.
Standard

Cargo Shoring Guidelines

2005-03-21
HISTORICAL
ARP5596A
This SAE Aerospace Recommended Practice (ARP) specifies guidelines for calculating and performing shoring (load spreading) required on board civil transport aircraft whenever a piece of cargo to be carried exceeds the aircraft's maximum allowable limits in area load, running load, or both. It provides both the engineering methods needed to properly design a shoring arrangement, and the main practical dos and donts known from experience to ensure its effectiveness in protecting the aircraft's structure against overload.
Standard

Cargo Shoring Guidelines

2003-04-24
HISTORICAL
ARP5596
This SAE Aerospace Recommended Practice (ARP) specifies guidelines for calculating and performing shoring (load spreading) required on board civil transport aircraft whenever a piece of cargo to be carried exceeds the aircraft's maximum allowable limits in area load, running load, or both. It provides both the engineering methods needed to properly design a shoring arrangement, and the main practical dos and donts known from experience to ensure its effectiveness in protecting the aircraft's structure against overload.
X