Refine Your Search

Date

Date

Topic

Topic

Safety AGE-3 Aircraft Ground Support Equipment Committee

Search Results

Viewing 1 to 20 of 42
123Next >Last >>
Sort by title
Standard

Wheel Chocks
2011-05-16
HISTORICAL
AIR4905
The purpose of this document is to present general considerations for the design and use of aircraft wheel chocks. The design and use of aircraft wheel chocks is a good deal more complicated than it may appear at first glance.
Standard

Telemetry Data Retrieval Standards for Ground Support Equipment (GSE)
2024-03-22
WIP
ARP8997
This SAE Aerospace Recommended Practice (ARP) describes the standards on telemetry data retrieval on ground support equipment (GSE), focusing on wiring requirements, connectors, signal definitions and communication protocols applicable in the industry.
Standard

SOLID-STATE FREQUENCY CONVERTER 400 HERTZ, 3-PHASE OUTPUT
1989-09-01
HISTORICAL
ARP1940
This specification covers the requirements for solid-state frequency converters with 480 [or 380] V 3-phase, 60 [or 50] Hz input and 115/200 V, 3-phase, 400 Hz output capable of powering aircraft type loads requiring MIL-STD-704D quality power. The frequency converter shall be a self-contained unit suitable for the environment of intended use. Typical applications include dedicated use at passenger loading bridges (mounted under the bridge in telescoping bridge applications or fixed installation at base of stationary type loading bridges) with weatherproof enclosures or hangar/lab use where indoor fixed or portable units can be used.
Standard

Ramp Markings
2021-09-30
CURRENT
ARP5910A
This SAE Aerospace Recommended Practice (ARP) outlines recommended ramp pavement marking standards for proper guidance and positioning of GSE on commercial transport aircraft parking and handling stands (gates), in line with International Civil Aviation (ICAO) recommendations applicable to airport aprons. Throughout this document, the minimum essential criteria are identified by use of the key word “shall”. Recommended criteria are identified by use of the key word “should” and, while not mandatory, are considered to be of primary importance in providing safety effective ramp markings. Deviation from recommended criteria should only occur after careful consideration and thorough service evaluation have shown alternate methods to provide an equivalent level of safety.
Standard

Minimum Safety Requirements for Special Purpose Airline Ground Support Equipment
2014-05-29
CURRENT
AIR1375D
This document applies to special purpose equipment which is used in the ground handling, servicing, and maintenance of transport aircraft. Fixed airport facilities and equipment covered under other sections of Part 1910 of Code of Federal Regulations (OSHA) are excluded from the scope of this document.
Standard

Minimum Safety Requirements for Special Purpose Airline Ground Support Equipment
2000-06-01
HISTORICAL
AIR1375C
This document applies to special purpose equipment which is used in the ground handling, servicing, and maintenance of transport aircraft. Fixed airport facilities and equipment covered under other sections of Part 1910 of Code of Federal Regulations (OSHA) are excluded from the scope of this document.
Standard

Maintenance of Batteries and Battery Charging and Servicing Facilities
2020-09-23
CURRENT
AIR1898A
This SAE Aerospace Information Report (AIR) covers, and is restricted to, hands-on servicing/ maintenance of industrial lead acid batteries used solely for motive power and exclusively for ground support equipment (GSE). It does not address or pertain to automotive-type SLI (starting-lighting-ignition) batteries or any other types of batteries (such as nickel-cadmium, zinc, or lithium batteries) which may be on-board airport GSE for either motive power or auxiliary uses. Similarly, the battery servicing and charging facilities described herein are those intended exclusively for industrial lead acid batteries.
Standard

MAINTENANCE OF BATTERIES AND BATTERY CHARGING AND SERVICING FACILITIES
1992-06-10
HISTORICAL
AIR1898
This SAE Aerospace Information Report (AIR) covers, and is restricted to, hands-on servicing/maintenance of industrial lead acid batteries used solely for motive power and exclusively for ground support equipment (GSE). It does not address or pertain to automotive-type SLI (starting-lighting-ignition) batteries or any other types of batteries (such as nickel-cadmium, zinc, or lithium batteries) which may be on-board airport GSE for either motive power or auxiliary uses. Similarly, the battery servicing and charging facilities described herein are those intended exclusively for industrial lead acid batteries.
Standard

Interface Protection - Ground Equipment to Aircraft
2019-03-28
CURRENT
ARP1558
This SAE Aerospace Recommended Practice (ARP) discusses damage to aircraft fuselages caused by ground equipment contact at servicing and recommends methods to be incorporated or considered in ground equipment design for protection against that damage.
Standard

Ground Support Equipment Hydraulic Systems, Design and Installation, Recommended Practices for
2022-12-16
CURRENT
ARP4943A
This SAE Aerospace Recommended Practice (ARP) covers the design and installation requirements for hydraulic systems (up to 8000 psig [56 MPa]) for ground support equipment (GSE). This ARP is derived from AS5440, which provides hydraulic system requirements for aircraft. The recommendations herein are primarily intended for GSE that exchange hydraulic fluid with the aircraft, such as hydraulic service carts, rather than GSE with non-interfacing hydraulic systems. The GSE may be mobile, portable, or stationary.
Standard

Ground Support Equipment Electrical Systems
2024-03-22
WIP
AIR1336C
This SAE Aerospace Information Report (AIR) considers the following major areas: 1. major components and their ratings; 2. selection criteria for optimum design balance for electrical systems; 3. effects of operating conditions and environment on both maintenance and life of components; 4. trouble signals - their diagnosis and cure.
Standard

GENERAL REQUIREMENTS FOR AEROSPACE POWERED MOBILE GROUND SUPPORT EQUIPMENT
1975-06-01
HISTORICAL
ARP1247A
This Recommended Practice outlines the basic general design requirements for powered mobile ground support equipment used in the civil air transport industry. It is intended to assist the airlines in standardizing requirements for various configurations of equipment.
Standard

Electrical Connectors for Use in Battery Powered Ground Support Equipment
2020-09-23
CURRENT
ARP1892B
This SAE Aerospace Recommended Practice (ARP) describes a two-pole electric connector for use in battery powered ground support equipment, i.e., traction batteries. Alternatively, the connector can have two or more auxiliary contacts for auxiliary circuits. A handle may be added as an option to assist in connecting and disconnecting.
Standard

ELECTRICAL CONNECTORS FOR USE IN BATTERY POWERED GROUND SUPPORT EQUIPMENT
1985-07-01
HISTORICAL
ARP1892
This recommended practice describes a two-pole electric connector for use in battery powered ground support equipment i.e. traction batteries. Alternatively, the connector can have two or more auxiliary contacts for auxiliary circuits. A handle may be added as an option to assist in connecting and disconnecting.
Standard

ELECTRICAL CONNECTORS FOR USE IN BATTERY POWERED GROUND SUPPORT EQUIPMENT
1991-04-29
HISTORICAL
ARP1892A
This recommended practice describes a two-pole electric connector for use in battery powered ground support equipment, i.e., traction batteries. Alternatively, the connector can have two or more auxiliary contacts for auxiliary circuits. A handle may be added as an option to assist in connecting and disconnecting.
Standard

Design and Safety Criteria for Passenger Boarding Stairways
2024-03-22
WIP
AIR6133A
This SAE Aerospace Information Report (AIR) is broken into various categories for convenience and ease of identification. It is the purpose of this document to provide certain criteria for the design and selection of stairways, for the boarding of passengers onto an aircraft. The criteria presented are limited to those factors which affect the safety of the passengers and are coordinated, where applicable, with the practices of the architectural profession, with respect to the design of stairways. Comprehensive design requirements for passenger stairs can be found in the industry documents listed under 2.1.3, 2.1.4, and 2.1.5 hereafter. The recommended practices are applicable to both mobile variable-elevation type stairways and to fixed-elevation stairways of the type built into an aircraft fuselage.
123Next >Last >>
X