Refine Your Search

Topic

Search Results

Standard

Vacuum Brake Hose

2014-09-18
CURRENT
J1403_201409
The vacuum brake hose is intended for use in the power braking systems of vehicles or as connections on vacuum lines of vehicles or systems thereof. For the purposes of clearly identifying hose classification and for specification simplification, vacuum brake hose is divided into two types: heavy-wall Type H, and light-wall Type L.
Standard

Vacuum Brake Hose

2005-03-30
HISTORICAL
J1403_200503
The vacuum brake hose is intended for use in the power braking systems of vehicles or as connections on vacuum lines of vehicles or systems thereof. For the purposes of clearly identifying hose classification and for specification simplification, vacuum brake hose is divided into two types: heavy-wall Type H, and light-wall Type L.
Standard

VACUUM BRAKE HOSE

1985-06-01
HISTORICAL
J1403_198506
Vacuum brake hose is intended for use in the power braking systems of vehicles or as connections on transmission lines in combinations of vehicles or systems thereof. For the purpose of clearly identifying the scopes and simplification of the specification, the vacuum brake hose specification is divided into two types with two classes as follows: Heavy-Wall Type H, Class A and B and Light-Wall Type L, Class A and B.
Standard

VACUUM BRAKE HOSE

1989-07-01
HISTORICAL
J1403_198907
The vacuum brake hose is intended for use in the power braking systems of vehicles or as connections on transmission lines in combinations of vehicles or systems thereof. For the purposes of clearly identifying hose classification and for specification simplification, vacuum brake hose is divided into two types: heavy-wall Type H, and light-wall Type L.
Standard

Road Vehicle—Hydraulic Brake Hose Assemblies for Use With Nonpetroleum-Base Hydraulic Fluids

1999-09-09
HISTORICAL
J1401_199909
This SAE Standard specifies the performance tests and requirements for hydraulic brake hose assemblies used in the hydraulic braking system of a road vehicle. It also specifies the methods used for identification of the hose manufacturer. This document applies to brake hose assemblies made of a hose fabricated from yarn and natural or synthetic elastomers and assembled with metal end fittings for use with nonpetroleum-base brake fluids as specified in SAE J1703 and SAE J1705. The nominal internal diameter of the brake hose shall fall within one of the following values: a 3.5 mm or less (1/8 in or less) b 4 to 5 mm (3/16 in)
Standard

Road Vehicle—Hydraulic Brake Hose Assemblies for Use With Nonpetroleum-Base Hydraulic Fluids

2003-06-10
HISTORICAL
J1401_200306
This SAE Standard specifies the performance tests and requirements for hydraulic brake hose assemblies used in the hydraulic braking system of a road vehicle. It also specifies the methods used for identification of the hose manufacturer. This document applies to brake hose assemblies made of a hose fabricated from yarn and natural or synthetic elastomers and assembled with metal end fittings for use with nonpetroleum-base brake fluids as specified in SAE J1703 and SAE J1705. The nominal internal diameter of the brake hose shall fall within one of the following values: a 3.5 mm or less (1/8 in or less) b 4 to 5 mm (3/16 in)
Standard

Road Vehicle--Hydraulic Brake Hose Assemblies for Use With Nonpetroleum-Base Hydraulic Fluids

1990-06-01
HISTORICAL
J1401_199006
This SAE Standard specifies the performance tests and requirements for hydraulic brake hose assemblies used in the hydraulic braking system of a road vehicle. It also specifies the methods used for identification of the hose manufacturer. This document applies to brake hose assemblies made of a hose fabricated from yarn and natural or synthetic elastomers and assembled with metal end fittings for use with nonpetroleum-base brake fluids as specified in SAE J1703 and SAE J1705. The nominal internal diameter of the brake hose shall fall within one of the following values: 3.5 mm or less (1/8 in or less) 4 to 5 mm (3/16 in)
Standard

Road Vehicle - Hydraulic Brake Hose Assemblies for Use With Nonpetroleum-Base Hydraulic Fluids

2013-02-05
CURRENT
J1401_201302
This SAE Standard specifies the performance tests and requirements for hydraulic brake hose assemblies used in the hydraulic braking system of a road vehicle. It also specifies the methods used for identification of the hose manufacturer. This document applies to brake hose assemblies made of a hose fabricated from yarn and natural or synthetic elastomers and assembled with metal end fittings for use with nonpetroleum-base brake fluids as specified in SAE J1703, SAE J1704 and SAE J1705. The nominal internal diameter of the brake hose shall fall within one of the following values: a less than 4 mm (1/8 in or less) b 4 to 5 mm (3/16 in)
Standard

Road Vehicle - Hydraulic Brake Hose Assemblies for Use With Nonpetroleum-Base Hydraulic Fluids

2016-08-17
WIP
J1401

This SAE Standard specifies the performance tests and requirements for hydraulic brake hose assemblies used in the hydraulic braking system of a road vehicle. It also specifies the methods used for identification of the hose manufacturer.

This document applies to brake hose assemblies made of a hose fabricated from yarn and natural or synthetic elastomers and assembled with metal end fittings for use with nonpetroleum-base brake fluids as specified in SAE J1703, SAE J1704 and SAE J1705.

The nominal internal diameter of the brake hose shall fall within one of the following values:

    a. less than 4 mm (1/8 in or less)
    b. 4 to 5 mm (3/16 in)

Standard

RUBBER SEALS FOR HYDRAULIC DISC BRAKE CYLINDERS

1995-01-10
HISTORICAL
J1603_199501
This SAE Standard describes the performance and part requirements for elastomeric seals used in highway vehicle disc brake calipers. Seals covered by this specification may be the solid section type (square, rectangular, O-ring, etc.) mounted stationary in the cylinder bore or on the movable piston.
Standard

RUBBER DUST BOOTS FOR THE HYDRAULIC DISK BRAKE PISTON

1991-09-30
HISTORICAL
J1570_199109
This SAE Standard covers molded rubber boots used on disc brake pistons to prevent the entrance of dirt and moisture which could cause corrosion and otherwise impair caliper operation. The specification includes performance tests of brake piston boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition or physical properties of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operating in a temperature range of −40 to + 120 °C ± 2 °C (−40 to + 248 °F ± 3.6 °F).
Standard

ROAD VEHICLE–HYDRAULIC BRAKE HOSE ASSEMBLIES FOR USE WITH NONPETROLEUM-BASE HYDRAULIC FLUIDS

1994-06-01
HISTORICAL
J1401_199406
This SAE Standard specifies the performance tests and requirements for hydraulic brake hose assemblies used in the hydraulic braking system of a road vehicle. It also specifies the methods used for identification of the hose manufacturer. This document applies to brake hose assemblies made of a hose fabricated from yarn and natural or synthetic elastomers and assembled with metal end fittings for use with nonpetroleum-base brake fluids as specified in SAE J1703 and SAE J1705. The nominal internal diameter of the brake hose shall be one of the following values: a 3.2 mm (1/8 in) or, b 4.8 mm (3/16 in)
Standard

Power Steering Return Hose—Low Pressure

1998-01-01
HISTORICAL
J189_199801
This SAE Standard covers hose fabricated from fabric braid and synthetic rubber, assembled with end fittings or user applied clamps for use in automotive power steering applications as flexible connections within the temperature range of –40 °C to +120 °C (–40 °F to 250 °F) average and 135 °C (275 °F) maximum peaks. Hose assemblies shall be suitable for 1.72 MPa (250 psi) maximum working pressure with end fittings and 0.69 MPa (100 psi) maximum working pressure with user applied clamps.
Standard

Power Steering Return Hose—Low Pressure

2003-06-05
HISTORICAL
J189_200306
This SAE Standard covers hose fabricated from fabric braid and synthetic rubber, assembled with end fittings or user applied clamps for use in automotive power steering applications as flexible connections within the temperature range of –40 °C to +120 °C (–40 °F to 250 °F) average and 135 °C (275 °F) maximum peaks. Hose assemblies shall be suitable for 1.72 MPa (250 psi) maximum working pressure with end fittings and 0.69 MPa (100 psi) maximum working pressure with user applied clamps.
Standard

Power Steering Return Hose - Low Pressure

2012-07-05
CURRENT
J189_201207
This SAE Standard covers hose fabricated from fabric braid and synthetic rubber, assembled with end fittings or user applied clamps for use in automotive power steering applications as flexible connections within the temperature range of -40 °C to +120 °C (-40 °F to 250 °F) average and 135 °C (275 °F) maximum peaks. Hose assemblies shall be suitable for 1.72 MPa (250 psi) maximum working pressure with end fittings and 0.69 MPa (100 psi) maximum working pressure with user applied clamps.
Standard

Power Steering Pressure Hose—Wire Braid

2007-08-07
HISTORICAL
J190_200708
This specification covers hose fabricated from wire braid and synthetic rubber, assembled with end fittings for use in automotive applications up to 10.3 MPa (1500 psi) maximum pressure, as flexible connections within the temperature range of −40 °C to 121 °C (−40 °F to +250 °F) average, 13.5 °C (275 °F) maximum peaks. The specification in this SAE Standard originated in the SAE-ASTM Technical Committee on Automotive Rubber (other than tires). They represent the correlation of the best information available from research investigation and production experience on the minimum constructional and performance characteristics essential for new power steering assemblies used as original or replacement equipment. This standard applies to passenger cars. It may prove useful to truck manufacturers, but it is not to be presented as present practices.
X