Refine Your Search

Search Results

Standard

ROAD VEHICLES—HIGH PRESSURE FUEL INJECTION PIPE END—CONNECTIONS WITH 60 DEGREE FEMALE CONE

1988-10-01
HISTORICAL
J1949_198810
This SAE Standard specifies the dimensional requirements for the assembly of high-pressure pipe connections for compression-ignition (diesel) engine fuel injection equipment. It applies to 60 degrees female cones with external threaded connectors types 1 and 2 (see Figures 1, 2, and 3), and to the internal threaded tube nuts and male cone type end assembly (see Figure 4) of high-pressure pipe connections for tubes with diameters up to 12 mm inclusive.
Standard

Fuel Injection Pumps—High Pressure Pipes (Tubing) for Testing

2002-10-25
HISTORICAL
J1418_200210
This SAE Standard specifies the dimensional requirement of a range of high pressure pipes for use in the bench testing and setting of fuel injection pumps. Only dimensions and requirements affecting the hydraulic characteristic of the pipes are defined. Other requirements, such as the type of end connections and shape of the pipes when bent, are not included. These depend on the connections provided at pump outlets and injector inlets, and on the design features of individual pumps and test benches.
Standard

Fuel Injection Equipment Nomenclature

1992-10-01
HISTORICAL
J830_199210
This SAE Standard establishes a vocabulary and definitions relating to the components used in fuel injection systems for compression ignition (diesel) engines. Definitions are separated into six sections by topic as follows: Section 3 Fuel Injection Pumps; Section 4 Fuel Injectors; Section 5 Unit Injectors; Section 6 Governors; Section 7 Timing Devices; Section 8 High Pressure Pipes and Connections.
Standard

Fuel Injection Equipment Nomenclature

2015-11-24
CURRENT
J830_201511
This SAE Standard establishes a vocabulary and definitions relating to the components used in fuel injection systems for compression ignition (diesel) engines. Definitions are separated into six sections by topic as follows: Section 3--Fuel Injection Pumps Section 4--Fuel Injectors Section 5--Unit Injectors Section 6--Governors Section 7--Timing Devices Section 8--High Pressure Pipes and Connections NOTE: When the word fuel is used in the terms listed it may be omitted providing there can be no misunderstanding.
Standard

Diesel Injection Pump Testing—Part 2: Orifice Plate Flow Measurement

2015-09-22
CURRENT
J968/2_201509
This part of SAE J968 specifies the flow measuring system, including the fixture, to be used for flow testing the single hole orifice plates used in an orifice plate type nozzle and holder assembly (described in SAE J968-1) which is intended for testing and setting diesel fuel injection pumps on test benches. The flow measuring system and fixture ensure accurate flow testing of the entire range of orifices from 0.4 to 0.8 mm diameter as specified in SAE J968-1. It is intended primarily for use by the manufacturers of single hole orifice plates.
Standard

Diesel Injection Pump Testing—Part 2: Orifice Plate Flow Measurement

2002-12-20
HISTORICAL
J968/2_200212
This part of SAE J968 specifies the flow measuring system, including the fixture, to be used for flow testing the single hole orifice plates used in an orifice plate type nozzle and holder assembly (described in SAE J968-1) which is intended for testing and setting diesel fuel injection pumps on test benches. The flow measuring system and fixture ensure accurate flow testing of the entire range of orifices from 0.4 to 0.8 mm diameter as specified in SAE J968-1. It is intended primarily for use by the manufacturers of single hole orifice plates.
Standard

Diesel Injection Pump Testing—Part 1: Calibrating Nozzle and Holder Assemblies

2002-12-20
HISTORICAL
J968/1_200212
This part of SAE J968 specifies two types of calibrating nozzle and holder assemblies intended for the testing and setting of diesel injection pumps on test benches. It applies to: a A calibrating nozzle and holder assembly with a single hole orifice plate; b A calibrating nozzle and holder assembly with a delay pintle type nozzle. The approximate range of the calibrating nozzle and holder assembly is up to: a 300 mm3/stroke with the single hole orifice plate; b 150 mm3/stroke with the delay pintle type nozzle. Setting and maintenance requirements are specified in ISO 4008/3.
Standard

Diesel Fuel Injector Assembly—Types 8, 9, 10, and 11

2002-12-13
HISTORICAL
J265_200212
This SAE Standard specifies the dimensional requirements necessary for the mounting and interchangeability of four types of fuel injectors in diesel engines. Two of the types specified are flats-located injectors. The location and dimensions of the fuel inlet, leak-off connections, and type of attachment are not defined since they may vary according to the particular application.
Standard

Diesel Fuel Injector Assembly-Types 8, 9, 10, and 11

1991-04-01
HISTORICAL
J265_199104
This SAE Standard specifies the dimensional requirements necessary for the mounting and interchangeability of four types of fuel injectors in diesel engines. Two of the types specified are flats-located injectors. The location and dimensions of the fuel inlet, leak-off connections and type of attachment are not defined since they may vary according to the particular application. This document is applicable to nozzle holder types 8 and 10 of an unspecified means of angular location and flats-located types 9 and 11 with a 17.0 mm (nominal) shank diameter. The internal construction of the fuel injector remains optional with the manufacturer.
Standard

Diesel Fuel Injector Assembly-Flange Mounted Types 5 and 6

1991-04-01
HISTORICAL
J629_199104
This SAE Standard specifies the dimensional requirements necessary for the mounting and interchangeability of two types of fuel injectors in diesel engines. The location and dimensions of the fuel inlet, leak-off connections, and flange design are not defined since they may vary according to the particular application. This document is applicable to nozzle holder types 5 and 6 of a flange mounted design with a 21.0 mm (nominal) shank diameter used with size "S" nozzles specified in ISO 2697. The internal construction of the fuel injector remains optional with the manufacturer.
Standard

Diesel Fuel Injector Assembly--Types 8, 9, 10, and 11

1983-08-01
HISTORICAL
J265_198308
This SAE Standard specifies the dimensional requirements necessary for the mounting and interchangeability of four types of fuel injectors in diesel engines. Two of the types specified are flats-located injectors. The location and dimensions of the fuel inlet, leak-off connections, and type of attachment are not defined since they may vary according to the particular application. Field of Application This document is applicable to nozzle holder types 8 and 10 of an unspecified means of angular location and flats-located types 9 and 11 with a 17.0 mm (nominal) shank diameter. The internal construction of the fuel injector remains optional with the manufacturer.
Standard

Diesel Fuel Injector Assembly Type 7 (9.5 mm)

1977-10-01
HISTORICAL
J347A_197710
This SAE Standard specifies the dimensional requirements necessary for the mounting and interchangeability of a type of fuel injector used in diesel engines. Field of Application This document is applicable to a clamp-mounted fuel injector of an integral nozzle and nozzle holder design with a 9.5 mm (nominal) holder shank diameter and deals only with the interface between the injector and the engine. The internal construction of the fuel injector remains optional with the manufacturer.
Standard

Diesel Fuel Injector Assembly Type 7 (9.5 mm)

1988-07-01
HISTORICAL
J347_198807
This SAE Standard specifies the dimensional requirements necessary for the mounting and interchangeability of a type of fuel injector used in diesel engines. Field of Application This document is applicable to a clamp-mounted fuel injector of an integral nozzle and nozzle holder design with a 9.5 mm (nominal) holder shank diameter and deals only with the interface between the injector and the engine. The internal construction of the fuel injector remains optional with the manufacturer.
Standard

Diesel Fuel Injector Assembly Type 7 (9.5 mm)

2015-11-24
CURRENT
J347_201511
This SAE Standard specifies the dimensional requirements necessary for the mounting and interchangeability of a type of fuel injector used in diesel engines. Field of Application This document is applicable to a clamp-mounted fuel injector of an integral nozzle and nozzle holder design with a 9.5 mm (nominal) holder shank diameter and deals only with the interface between the injector and the engine. The internal construction of the fuel injector remains optional with the manufacturer.
Standard

Diesel Fuel Injector Assembly Type 7 (9.5 mm)

2002-10-25
HISTORICAL
J347_200210
This SAE Standard specifies the dimensional requirements necessary for the mounting and interchangeability of a type of fuel injector used in diesel engines.
Standard

Diesel Fuel Injector Assembly Type 7 (9.5 Mm)

1995-07-10
HISTORICAL
J347_199507
This SAE Standard specifies the dimensional requirements necessary for the mounting and interchangeability of a type of fuel injector used in diesel engines. This document is applicable to a clamp-mounted fuel injector of an integral nozzle and nozzle holder design with a 9.5 mm (nominal) holder shank diameter and deals only with the interface between the injector and the engine. The internal construction of the fuel injector remains optional with the manufacturer.
X