Refine Your Search

Topic

Search Results

Standard

Alignment of Nut Slots

1990-01-01
CURRENT
J484_199001
This method of gaging alignment of nut slots allows equal variations for location of the cotter pin hole in the bolt and location of slots in the nut. To inspect the nut, the slotted gage is inserted through the nut hole from the bearing surface of the nut. Alignment of slots is considered satisfactory if the gage pin can be slipped into the gage and nut slots without interference.
Standard

Blind Rivets - Break Mandrel Type

2017-01-04
CURRENT
J1200_201701
This SAE Standard establishes the dimensional, mechanical, and performance requirements of inch and metric break mandrel blind rivets suitable for use in joining the component parts of an assembly.
Standard

Blind Rivets - Break Mandrel Type

2013-04-15
HISTORICAL
J1200_201304
This SAE Standard establishes the dimensional, mechanical, and performance requirements of inch and metric break mandrel blind rivets suitable for use in joining the component parts of an assembly.
Standard

Bolt and Capscrew Sizes for Use in Construction and Industrial Machinery

1994-06-01
HISTORICAL
J370_199406
This SAE Recommended Practice covers the use of preferred bolt and capscrew sizes, wherever applicable, on construction and industrial machinery to ease serviceability. Designers, in their efforts to determine the proper fastener for heavy equipment, sometimes overlook the practical aspects of serviceability. When a particular component requires frequent service, it is much faster and easier for the serviceman to work with common size, easily distinguished bolts and capscrews which require a minimum of tools. Section 4 lists eight diameters of recommended bolts and capscrews, some of which can be found in any hardware store, require only standard tools, are easy to distinguish, and at the same time cover proof loads from 1043 kg (2300 lb) on up at convenient intervals. While some applications may require other sizes and/or fine threaded fasteners for greater camping forces and/or area restrictions, the convenience of UNC threads in the sizes indicated is preferred wherever possible.
Standard

Bolt and Capscrew Sizes for Use in Construction and Industrial Machinery

1998-05-01
HISTORICAL
J370_199805
This SAE Recommended Practice covers the use of preferred bolt and capscrew sizes, wherever applicable, on construction and industrial machinery to ease serviceability. Designers, in their efforts to determine the proper fastener for heavy equipment, sometimes overlook the practical aspects of serviceability. When a particular component requires frequent service, it is much faster and easier for the serviceman to work with common size, easily distinguished bolts and capscrews which require a minimum of tools. Section 4 lists eight diameters of recommended bolts and capscrews, some of which can be found in any hardware store, require only standard tools, are easy to distinguish, and at the same time cover proof loads from 1043 kg (2300 lb) on up at convenient intervals. While some applications may require other sizes and/or fine threaded fasteners for greater camping forces and/or area restrictions, the convenience of UNC threads in the sizes indicated is preferred wherever possible.
Standard

Bolt and Capscrew Sizes for Use in Construction and industrial machinery

1968-11-01
HISTORICAL
J370_196811
This SAE Recommended Practice covers the use of preferred bolt and capscrew sizes, wherever applicable, on construction and industrial machinery to ease serviceability. Designers, in their efforts to determine the proper fastener for heavy equipment, sometimes overlook the practical aspects of serviceability. When a particular component requires frequent service, it is much faster and easier for the serviceman to work with common size, easily distinguished bolts and capscrews which require a minimum of tools. Section 4 lists eight diameters of recommended bolts and capscrews, some of which can be found in any hardware store, require only standard tools, are easy to distinguish, and at the same time cover proof loads from 1043 kg (2300 lb) on up at convenient intervals. While some applications may require other sizes and/or fine threaded fasteners for greater camping forces and/or area restrictions, the convenience of UNC threads in the sizes indicated is preferred wherever possible.
Standard

CONICAL SPRING WASHERS

1998-05-01
HISTORICAL
J773_199805
This SAE Standard covers dimensional, material, and general specifications and methods of test for two types of general purpose conical spring washers, designated type L and type H, for use as loose washers over screws and bolts, and also for use as pre-assembled washers in screw and washer assemblies.
Standard

Conical Spring Washers

1961-06-01
HISTORICAL
J773_196106
This SAE Standard covers dimensional, material, and general specifications and methods of tests for two types of general purpose conical spring washers, designated type L and type H, for use as loose washers over screws and bolts, and also for use as pre-assembled washers in screw and washer assemblies.
Standard

Conical Spring Washers

2016-08-31
CURRENT
J773_201608
This SAE Standard covers dimensional, material, and general specifications and methods of test for two types of general purpose conical spring washers, designated type L and type H, for use as loose washers over screws and bolts, and also for use as pre-assembled washers in screw and washer assemblies.
Standard

Cotter Pins

1990-01-01
CURRENT
J487_199001
Not available.
Standard

Decarburization in Hardened and Tempered Unified Threaded Fasteners

2013-01-02
CURRENT
J121_201301
This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.
Standard

Dryseal Pipe Threads

2013-02-01
CURRENT
J476_201302
The Dryseal American Standard Taper Pipe Thread, the Dryseal American Fuel Internal Straight Pipe Thread and the Dryseal American Intermediate Internal Straight Pipe Thread covered by this standard conform with the American Standard ASA-B2.2. The Dryseal SAE-Short Taper Pipe Thread in this standard conforms with the Dryseal American Standard Taper Pipe Thread except for the length of thread, which is shortened for increased clearance and economy of material. The significant feature of the Dryseal thread is controlled truncation at the crest and root to assure metal to metal contact coincident with or prior to flank contact. Contact at the crest and root prevents spiral leakage and insures pressure-tight joints without the use of a lubricant or sealer. Lubricants, if not functionally objectionable, may be used to minimize the possibility of galling in assembly.
Standard

FLANGED 12-POINT SCREWS

1998-05-01
HISTORICAL
J58_199805
Included in this SAE Standard are the detailed general and dimensional specifications applicable to flanged 12-point screws recognized as SAE Standard and intended for general use in automotive and other ground-based vehicles and industrial equipment. Also included is Appendix A, covering runout sleeve gages and gaging. The inclusion of dimensional data in this standard is not intended to imply that all of the products described are stock production sizes. Consumers should consult manufacturers concerning availability of product.
Standard

Flanged 12-Point Screws

2015-02-26
CURRENT
J58_201502
Included in this SAE Standard are the detailed general and dimensional specifications applicable to flanged 12-point screws recognized as SAE Standard and intended for general use in automotive and other ground-based vehicles and industrial equipment. The inclusion of dimensional data in this standard is not intended to imply that all of the products described are stock production sizes. Consumers should consult manufacturers concerning availability of product.
Standard

Grooved Straight Pins

1964-06-01
HISTORICAL
J494_196406
Material-Cold drawn SAE 1112 or 1113 steel, alloy steel or copper alloy as specified by purchaser. Unless otherwise specified, steel pins shall have a flash plate of cadmium or zinc for protection of pins in transit or storage. Grooved Straight Pins must be free from burrs and all other defects that might affect their use and serviceability.
Standard

Guide for Rivet Selection and Design Consideration

2016-11-23
CURRENT
J492_201611
This is a guide intended to aid the user in the proper selection and application of rivets as a fastening means. It consists of general information on the advantages of riveting, various methods of riveting, selection of rivets and design considerations.
Standard

Guide for Rivet Selection and Design Consideration

2013-04-16
HISTORICAL
J492_201304
This is a guide intended to aid the user in the proper selection and application of rivets as a fastening means. It consists of general information on the advantages of riveting, various methods of riveting, selection of rivets and design considerations.
Standard

Guide for Rivet Selection and Design Consideration

2005-06-30
HISTORICAL
J492_200506
This small solid rivet standard covers the complete general and dimensional data for flat head, pan head, button head, truss head, countersunk head, copper's, tinner's and belt rivets. Design and assembly data are given in the Appendix—Rivet Selection and Design Considerations. The inclusion of dimensional data in this standard is not intended to imply that all of the products described are stock production sizes. Consumers are requested to consult with manufacturers concerning stock production sizes.
Standard

Hex Bolts

1990-01-01
CURRENT
J105_199001
Included herein are complete general and dimensional data for the various types of square and hex bolts recognized as SAE Standard and commonly used in automotive and other ground based motor vehicles and industrial equipment. Also included are appendixes covering wrench openings for bolts and thread runout sleeve gages. The inclusion of dimensional data in this standard is not intended to imply that all of the products described are stock production sizes. Users are requested to consult with manufacturers concerning lists of stock production sizes.
Standard

Hexagon High Nuts

1998-05-01
HISTORICAL
J482_199805
Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ANSI/ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.
X