Refine Your Search

Search Results

Standard

Torque-Tension Tightening for Metric Series Fasteners

2017-11-08
CURRENT
J1701M_201711
This SAE Information Report is provided as an advisory guide. Individual application discretion is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. The document covers a number of the variables in the torque-tension relationship: friction, materials, temperature, humidity, fastener and mating part finishes, surfaces, and the kind of tightening tools or equipment used. Also described in this document is the torque management required to achieve satisfactory fastened joint tightening. This guide is limited in application to clearance fit threads, such as the common 6g/6H class of fit. Other thread types including interference fit, mechanical locking, prevailing torque, or forms other than ISO-Metric may apply to some aspects of this standard but are not specifically covered.
Standard

Thread Rolling Screws

2012-07-05
CURRENT
J81_201207
This SAE Standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that "thread rolling" screws have performance capabilities beyond those normally expected of other standard types of tapping screws.) NOTE—The performance requirements covered in this document apply only to the combination of laboratory conditions described in the testing procedures. If other conditions are encountered in an actual service application (such as different materials, thicknesses, hole sizes, etc.), values shown herein for drive torque, torque-to-clamp load, and proof torque may require adjustment.
Standard

Surface Discontinuities on Bolts, Screws, and Studs in Fatigue Applications

1994-03-22
HISTORICAL
J123_199403
This SAE recommended practice defines, illustrates, and specifies allowable limits for various types of surface discontinuities that may occur or become apparent during the manufacture and processing of bolts, screws, and studs which are primarily intended for use in automotive assemblies subjected to severe dynamic stresses and necessitating use of high strength fasteners having appropriate fatigue-resistant properties. The basic document does not include inspection sampling requirements. It is intended that the purchaser shall specify, in the original inquiry and purchase order, the inspection sampling requirements which the producer must satisfy to demonstrate the acceptability of bolts and screws with respect to surface discontinuities. Appendix A outlines inspection sampling plans applicable when such requirements are not specified by the purchaser in the original injury, purchase order, or in related specifications.
Standard

Surface Discontinuities on Bolts, Screws, and Studs in Fatigue Applications

1976-06-01
HISTORICAL
J123C_197606
This SAE recommended practice defines, illustrates, and specifies allowable limits for various types of surface discontinuities that may occur or become apparent during the manufacture and processing of bolts, screws, and studs which are primarily intended for use in automotive assemblies subjected to severe dynamic stresses and necessitating use of high strength fasteners having appropriate fatigue-resistant properties. The basic document does not include inspection sampling requirements. It is intended that the purchaser shall specify, in the original inquiry and purchase order, the inspection sampling requirements which the producer must satisfy to demonstrate the acceptability of bolts and screws with respect to surface discontinuities. Appendix A outlines inspection sampling plans applicable when such requirements are not specified by the purchaser in the original injury, purchase order, or in related specifications.
Standard

Surface Discontinuities on Bolts, Screws, and Studs in Fatigue Applications

1975-07-01
HISTORICAL
J123B_197507
This SAE recommended practice defines, illustrates, and specifies allowable limits for various types of surface discontinuities that may occur or become apparent during the manufacture and processing of bolts, screws, and studs which are primarily intended for use in automotive assemblies subjected to severe dynamic stresses and necessitating use of high strength fasteners having appropriate fatigue-resistant properties. The basic document does not include inspection sampling requirements. It is intended that the purchaser shall specify, in the original inquiry and purchase order, the inspection sampling requirements which the producer must satisfy to demonstrate the acceptability of bolts and screws with respect to surface discontinuities. Appendix A outlines inspection sampling plans applicable when such requirements are not specified by the purchaser in the original injury, purchase order, or in related specifications.
Standard

Surface Discontinuities on Bolts, Screws, and Studs in Fatigue Applications

1976-06-01
HISTORICAL
J123_197606
This SAE recommended practice defines, illustrates, and specifies allowable limits for various types of surface discontinuities that may occur or become apparent during the manufacture and processing of bolts, screws, and studs which are primarily intended for use in automotive assemblies subjected to severe dynamic stresses and necessitating use of high strength fasteners having appropriate fatigue-resistant properties. The basic document does not include inspection sampling requirements. It is intended that the purchaser shall specify, in the original inquiry and purchase order, the inspection sampling requirements which the producer must satisfy to demonstrate the acceptability of bolts and screws with respect to surface discontinuities. Appendix A outlines inspection sampling plans applicable when such requirements are not specified by the purchaser in the original injury, purchase order, or in related specifications.
Standard

Surface Discontinuities on Bolts, Screws, and Studs in Fatigue Applications

2012-04-10
CURRENT
J123_201204
This SAE Recommended Practice defines, illustrates, and specifies allowable limits for various types of surface discontinuities that may occur or become apparent during the manufacture and processing of bolts, screws, and studs which are primarily intended for use in automotive assemblies subjected to severe dynamic stresses and necessitating use of high strength fasteners having appropriate fatigue-resistant properties.
Standard

Spring Nuts

2016-11-28
CURRENT
J891_201611
Included herein are complete general and dimensional specifications for metric and inch types of spring nuts recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw is considered adequate for the application. It should be noted that spring nuts having other configurations, dimensions, provisions for ground, etc., are available and manufacturers should be consulted.
Standard

Spring Nuts

2013-04-16
HISTORICAL
J891_201304
Included herein are complete general and dimensional specifications for metric and inch types of spring nuts recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw is considered adequate for the application. It should be noted that spring nuts having other configurations, dimensions, provisions for ground, etc., are available and manufacturers should be consulted.
Standard

Metric Thread Rolling Screws

2017-09-07
CURRENT
J1237_201709
This SAE Standard covers material, dimensional, performance and test requirements for metric thread rolling screws suitable for use in general engineering applications.
Standard

Metric Thread Rolling Screws

2001-03-12
HISTORICAL
J1237_200103
This SAE Standard covers requirements for metric thread rolling screws suitable for use in general engineering applications.
Standard

Metric Thread Rolling Screws

2018-08-20
WIP
J1237
This SAE Standard covers material, dimensional, performance and test requirements for metric thread rolling screws suitable for use in general engineering applications.
Standard

Mechanical and Quality Requirements for Machine Screws

2013-01-08
CURRENT
J82_201301
This SAE Standard covers the mechanical and quality requirements for two grades of carbon steel, slotted, and recessed, 82 degrees flat countersunk, 82 degrees oval countersunk, pan, fillister, hex, and hex washer head machine screws in sizes No. 4 through 3/4 in for use automotive and related industries. The dimensions of these screws are covered in ASME B18.6.3.
Standard

Mechanical and Material Requirements for Wheel Bolts

2016-11-21
CURRENT
J1102_201611
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened
Standard

Mechanical and Material Requirements for Wheel Bolts

2013-04-11
HISTORICAL
J1102_201304
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened
Standard

Mechanical and Material Requirements for Steel Nuts

1999-07-01
HISTORICAL
J995_199907
This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 in, inclusive, and with dimensions conforming with the requirements of the latest issue of ASME B18.2.2 or ASME B18.6.3, as applicable. This document does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For sizes 1/4 through 1 in, this may be done by the statement: "Surface discontinuities shall not exceed the limits specified in SAE J122."
Standard

Mechanical and Material Requirements for Metric Wheel Bolts

2013-04-11
HISTORICAL
J1102M_201304
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened
Standard

Mechanical and Material Requirements for Metric Wheel Bolts

2016-11-18
CURRENT
J1102M_201611
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened
Standard

Mechanical and Material Requirements for Metric Externally Threaded Steel Fasteners

1996-12-01
HISTORICAL
J1199_199612
This SAE Standard covers the mechanical and material requirements for eight property classes of steel, externally threaded metric fasteners in sizes M1.6 through M36, inclusive, and suitable for use in automotive and related applications. Products included are bolts, screws, studs, U-bolts, preassembled screw and washer assemblies (sems), and products manufacturered the same as sems except without washer. Products not covered are tapping screws, thread-rolling screws, and self- drilling screws. Mechanical and material requirements for these products are covered in other SAE documents. The term stud as referred to herein, applies to a cylindrical rod of moderate length, threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. For specification purposes, this document treats U-bolts as studs.
X