Search Results

Standard

Torque-Tension Test Procedure for Steel Threaded Fasteners - Metric Series

2017-01-03

CURRENT

J174M_201701

This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 6 through 24 mm nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the inch series version, see SAE J174.

Standard

Thread Rolling Screws

2012-07-05

CURRENT

J81_201207

This SAE Standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that "thread rolling" screws have performance capabilities beyond those normally expected of other standard types of tapping screws.) NOTE—The performance requirements covered in this document apply only to the combination of laboratory conditions described in the testing procedures. If other conditions are encountered in an actual service application (such as different materials, thicknesses, hole sizes, etc.), values shown herein for drive torque, torque-to-clamp load, and proof torque may require adjustment.

Standard

Thread Rolling Screws

1997-09-01

HISTORICAL

J81_199709

This SAE Standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that "thread rolling" screws have performance capabilities beyond those normally expected of other standard types of tapping screws.)

Standard

THREAD ROLLING SCREWS

1972-07-01

HISTORICAL

J81_197207

This standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that “thread rolling” screws have performance capabilities beyond those normally expected of other standard types of tapping screws.) Note: The performance requirements covered in this standard apply only to the combination of laboratory conditions described in the testing procedures. If other conditions are encountered in an actual service application (such as different materials, thicknesses, hole sizes, etc.), values shown herein for drive torque, torque-to-clamp load, and proof torque may require adjustment.

Standard

THREAD ROLLING SCREWS

1979-06-01

HISTORICAL

J81_197906

This standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that "thread rolling" screws have performance capabilities beyond those normally expected of other standard types of tapping screws.) Note: The performance requirements covered in this standard apply only to the combination of laboratory conditions described in the testing procedures. If other conditions are encountered in an actual service application (such as different materials, thicknesses, hole sizes, etc.), values shown herein for drive torque, torque-to-clamp load, and proof torque may require adjustment.

Standard

Surface Discontinuities on Nuts

1998-05-01

HISTORICAL

J122_199805

This SAE Recommended Practice defines, illustrates, and specifies allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of metric-series nuts, in sizes 6.3 to 25 mm and inch-series nuts in sizes 1/4 to 1 in, inclusive, which are primarily intended for use in automotive assemblies.

Standard

Surface Discontinuities on General Application Bolts, Screws, and Studs

1998-05-01

HISTORICAL

J1061_199805

This SAE Recommended Practice defines, illustrates, and specifies allowable limits for various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and studs in sizes through 24 mm or 1 in diameter inclusive with lengths to 150 mm or 6 in inclusive, having specified minimum tensile strengths of 900 MPa or 120 000 psi and greater, which are primarily intended for use in automotive assemblies.

Standard

Steel Stamped Nuts of One Pitch Thread Design - Metric Series

2016-11-18

CURRENT

J1053M_201611

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the inch equivalent of this document, see SAE J1053.

Standard

Steel Stamped Nuts of One Pitch Thread Design - Metric Series

2013-04-11

HISTORICAL

J1053M_201304

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the inch equivalent of this document, see SAE J1053.

Standard

Steel Stamped Nuts of One Pitch Thread Design - Inch Series

2016-11-18

CURRENT

J1053_201611

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the metric equivalent of this document, see SAE J1053M.

Standard

Steel Stamped Nuts of One Pitch Thread Design - Inch Series

2013-04-11

HISTORICAL

J1053_201304

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the metric equivalent of this document, see SAE J1053M.

Standard

Steel Self-Drilling Tapping Screws

2021-07-28

CURRENT

J78_202107

This SAE Standard covers the dimensional and general specifications, including performance requirements, for carbon steel self-drilling tapping screws suitable for use in general applications having point Styles 2, 3, 4, and 5. It is the objective of this document to ensure that carbon steel self-drilling tapping screws, by meeting the mechanical and performance requirements specified, shall drill a hole and form or cut mating threads in materials into which they are driven without deforming their own thread and without breaking during assembly.

Standard

Steel Self-Drilling Tapping Screws

1998-05-01

HISTORICAL

J78_199805

This SAE Standard covers the dimensional and general specifications, including performance requirements, for carbon steel self-drilling tapping screws suitable for use in general applications. It is the objective of this document to insure that carbon steel self-drilling tapping screws, by meeting the mechanical and performance requirements specified, shall drill a hole and form or cut mating threads in materials into which they are driven without deforming their own thread and without breaking during assembly. Appendix A is included to provide a recommended technique for measuring the case depth on the screws.

Standard

Steel Self-Drilling Tapping Screws

2013-04-16

HISTORICAL

J78_201304

This SAE Standard covers the dimensional and general specifications, including performance requirements, for carbon steel self-drilling tapping screws suitable for use in general applications. It is the objective of this document to insure that carbon steel self-drilling tapping screws, by meeting the mechanical and performance requirements specified, shall drill a hole and form or cut mating threads in materials into which they are driven without deforming their own thread and without breaking during assembly. Appendix A is included to provide a recommended technique for measuring the case depth on the screws.

Standard

Steel Self-Drilling Tapping Screws

2022-04-14

WIP

J78

This SAE Standard covers the dimensional and general specifications, including performance requirements, for carbon steel self-drilling tapping screws suitable for use in general applications having point Styles 2, 3, 4, and 5. It is the objective of this document to ensure that carbon steel self-drilling tapping screws, by meeting the mechanical and performance requirements specified, shall drill a hole and form or cut mating threads in materials into which they are driven without deforming their own thread and without breaking during assembly.

Standard

SURFACE DISCONTINUITIES ON GENERAL APPLICATION BOLTS, SCREWS, AND STUDS

1975-07-01

HISTORICAL

J1061A_197507

This recommended practice defines, illustrates, and specifies allowable limits for various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and studs in sizes through 24 mm or 1 in. diameter inclusive with lengths to 150 mm or 6 in. inclusive, having specified minimum tensile strengths of 900 MPa or 120,000 psi and greater, which are primarily intended for use in automotive assemblies.

Standard

SURFACE DISCONTINUITIES ON GENERAL APPLICATION BOLTS, SCREWS, AND STUDS

1992-10-01

HISTORICAL

J1061_199210

This SAE Recommended Practice defines, illustrates, and specifies allowable limits for various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and studs in sizes through 24 mm or 1 in diameter inclusive with lengths to 150 mm or 6 in inclusive, having specified minimum tensile strengths of 900 MPa or 120 000 psi and greater, which are primarily intended for use in automotive assemblies.

Standard

SURFACE DISCONTINUITIES ON BOLTS, SCREWS, AND STUDS

1976-06-01

HISTORICAL

J123_197606

This recommended practice defines, illustrates, and specifies allowable limits for various types of surface discontinuities that may occur or become apparent during the manufacture and processing of bolts, screws, and studs which are primarily intended for use in automotive assemblies subjected to severe dynamic stresses and necessitating use of high-strength fasteners having appropriate fatigue resistant properties.

Standard

SURFACE DISCONTINUITIES ON BOLTS, SCREWS, AND STUDS

1976-06-01

HISTORICAL

J123C_197606

This recommended practice defines, illustrates, and specifies allowable limits for various types of surface discontinuities that may occur or become apparent during the manufacture and processing of bolts, screws, and studs which are primarily intended for use in automotive assemblies subjected to severe dynamic stresses and necessitating use of high strength fasteners having appropriate fatigue resistant properties.

Standard

STEEL STAMPED NUTS OF ONE PITCH THREAD DESIGN—METRIC SERIES

1996-08-01

HISTORICAL

J1053M_199608

Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the inch equivalent of this document, see SAE J1053.