Search Results

Urea based mobile Selective Catalytic Reduction (SCR) systems typically use a pulse width modulated injector to control the amount of reductant added to the exhaust stream. Additionally, an air assist system is provided to ensure uniform distribution of the reductant in the exhaust and to prevent injector clogging. We report on the adaptation of a commercially available pulse width modulated injector for use with a urea solution and an air assist. Flow rates and flow rate reproducibility were determined at combinations of pulse width, frequency and injector pressure drop selected to span the injector operating range. After correcting for density, deviations in flowrates were determined from the published injector calibration data when using n-heptane. These deviations were not uniform across the injector map. At the combination of low pulse width and high frequency, the deviation from the published n-heptane calibration data was the greatest.

This paper describes the experiments conducted to determine the effect of high energy multiple spark discharge (MSD) ignition systems and spark plug electrode design, on the cold start performance of a vehicle which was converted for dedicated operation on E85 (a blend of 85% ethanol and 15% gasoline) fuel. Tests were conducted using three different ignition configurations; original equipment manufacturer (OEM) ignition and spark plugs, high energy multiple spark discharge (MSD) ignition with OEM, J-type spark plugs, and high energy MSD ignition with surface gap electrode spark plugs. The high energy MSD ignition with OEM spark plugs showed a significant improvement in cold start performance over the OEM ignition. The addition of the surface gap spark plugs caused a decrease in cold start performance. Despite this, the surface gap spark plugs produced higher ending coolant temperature than the other configurations.

This paper describes experiments conducted to determine the effect of multiple spark discharge ignition systems and spark plug electrode design on cold start performance of a dedicated E85 fueled vehicle. Tests were conducted using three different ignition configurations: OEM ignition and spark plugs, multiple spark discharge ignition with OEM spark plugs, and multiple spark discharge ignition with large gap circular electrode spark plugs. The multiple spark discharge ignition with OEM spark plugs showed a significant improvement in cold start performance over the OEM ignition, but the addition of the circular electrode spark plugs caused a decrease in cold start performance. The circular ground spark plugs did produce a higher ending coolant temperature than either of the other configurations.

In an effort to develop a five passenger sedan capable of achieving the Partnership for a New Generation of Vehicles (PNGV) objectives, a 1996 Ford Taurus sedan was converted into a parallel drive, hybrid electric vehicle. This vehicle was designed to retain, to the greatest degree possible, the basic driving characteristics of the conventionally powered vehicle. To achieve the high PNGV fuel economy goals, every effort was made to reduce weight and to use components that are more efficient than those of the original vehicle. The OEM automatic transmission has been replaced with a five-speed, manual transmission which was adapted from an earlier model year production Taurus SHO vehicle. In order to provide the driveability of an automatic transmission, an electro-hydraulic control unit was designed and built. This unit automatically engages the clutch and shifts gears as required during vehicle operation.

Kettering University's Clean Snowmobile Challenge student design team has developed a new robust and innovative snowmobile for the 2004 competition. Switching from the previous years four-stroke automotive engine, Kettering University has utilized a modified snowmobile in-line four cylinder, four-stroke, fuel- injected engine. This engine has been installed into a 2003 Yamaha RX-1 snowmobile chassis. Exhaust emissions have been minimized through the use of a customized catalytic converter and an electronically controlled closed-loop fuel injection system. A newly designed and tuned exhaust as well as several chassis treatments have aided in minimizing noise emissions.

A 1999 Chevrolet Silverado truck was converted to operate on E85 (a blend of 85% ethanol and 15% gasoline). The vehicle design was centered around four primary customer driven goals: maintaining or exceeding the performance of the current gasoline fueled vehicle, improving emissions, constructing a system that can be easily and economically integrated into production, and finally making this system invisible to the operator. Ethanol is a good choice for an alternative fuel, however it has some drawbacks. High ethanol blend fuels can provide lower exhaust and evaporative emissions, higher power, and higher efficiency than engines operating on gasoline. However, cold startability and material compatibility issues must be addressed. This paper describes the design modifications and performance changes resulting from the conversion to dedicated, high ethanol blend fuel operation.

Cylinder air/fuel ratio distribution is an important factor affecting the economy, power, vibration, and emissions of an internal combustion engine. Currently, production automobiles utilize an exhaust gas sensor located in the main exhaust stream in order to regulate air/fuel mixtures. By measuring the oxygen content of the exhaust gas for each cylinder independently, the degree of air/fuel variation between cylinders can be determined. This information can be used to determine the mixture quality of specific cylinders. Knowing these variances can lead to design changes in the intake and exhaust manifolds as well as better control of fuel metering which will improve the output of the engine. This study was carried out using a 1991 3.8L Buick V-6 engine with customized exhaust manifolds utilizing exhaust gas oxygen sensors for each cylinder in addition to the sensor located in the main combined exhaust gas stream. Production level, ZrO2 sensors were used for this experimental study.

Affordable clean snowmobile technology has been developed. The goals of this design included reducing exhaust emissions to levels which are below the U.S Environmental Protection Agency (EPA) 2012 standard. Additionally, noise levels were to be reduced to below the noise mandates of 78 dB(A). Further, this snowmobile can operate using any blend of gasoline and ethanol from E0 to E85. Finally, achieving these goals would be a hollow victory if the cost and performance of the snowmobile were severely compromised. Snowmobiling is, after all, a recreational sport; thus the snowmobile must remain fun to drive and cost effective to produce. The details of this design effort including performance data are discussed in this paper. Specifically, the effort to modify a commercially available snowmobile using a two cylinder, four-stroke engine is described. This snowmobile was modified to run on a range of ethanol blended fuels using a closed-loop engine control system.

Clean snowmobile technology has been developed and applied to an existing commercially available snowmobile. The goals of this effort included reducing exhaust emissions to levels which are below the U.S Environmental Protection Agency (EPA) 2012 standard. Additionally, noise levels were to be reduced to below the noise mandates of 78 dB(A). Further, this snowmobile can operate using any blend of gasoline and ethanol from E20 to E30. All of these goals were achieved while keeping the cost affordable. Snowmobiling is, after all, a recreational sport; thus the snowmobile must remain fun to drive and cost effective to produce. The details of this design effort including performance data are discussed in this paper. Specifically, the effort to modify a commercially available snowmobile using a three cylinder, four-stroke engine is described. This snowmobile was modified to run on a range of ethanol blended fuels using a closed-loop engine control system.

Kettering University has developed a cleaner and quieter snowmobile using technologies and innovative methods which can be applied in the real world with a minimal increase in cost. Specifically, a commercially available snowmobile using a two cylinder, four-stroke engine has been modified to run on high-blend ethanol (E-85) fuel. Further, a new exhaust system which features customized catalytic converters and mufflers to minimize engine noise and exhaust emissions has developed. A number of additional improvements have been made to the track to reduce friction and diminish noise. This paper provides details of the snowmobile development the results of these efforts on performance and emissions. Specifically, the Kettering University snowmobile achieved reductions of approximately 72% in CO, and 98% in HC+NOx when compared with the 2012 standard. Further, the snowmobile achieved a drive by noise level of 73 dbA while operating on hard packed snow.

Kettering University's entry for the 2006 Clean Snowmobile challenge utilizes a Polaris FST Switchback. This snowmobile having a two cylinder, four-stroke engine has been modified to run on ethanol (E-85). The student team has designed and built a new exhaust system which features customized catalytic converters to minimize engine out emissions. A number of improvements have been made to the track to reduce friction and diminish noise.

Kettering University's Clean Snowmobile Challenge student design team has developed a new robust and innovative snowmobile for the 2005 competition. This snowmobile dramatically reduces exhaust and noise emissions and improves fuel economy compared with a conventional snowmobile. Kettering University has utilized a modified snowmobile in-line four cylinder, four-stroke, engine. The team added an electronically-controlled fuel-injection system with oxygen sensor feedback to this engine. This engine has been installed into a 2003 Yamaha RX-1 snowmobile chassis. Exhaust emissions have been further minimized through the use of a customized catalytic converter and an electronically controlled closed-loop fuel injection system. A newly designed and tuned exhaust as well as several chassis treatments have aided in minimizing noise emissions.

Clean snowmobile technology has been developed using methods which can be applied in the real world with a minimal increase in cost. Specifically, a commercially available snowmobile using a two cylinder, four-stroke engine has been modified to run on high-blend ethanol (E-85) fuel. Additionally, a new exhaust system which features customized catalytic converters and mufflers to minimize engine noise and exhaust emissions has developed. Finally, a number of additional improvements have been made to the track to reduce friction and diminish noise. The results of these efforts include emissions reductions of 94% when compared with snowmobiles operating at the 2012 U.S. Federal requirements.

Clean snowmobile technology has been developed and applied to a commercially available two cylinder, four-stroke snowmobile. The goals of this effort included reducing exhaust and noise emissions to levels below the U.S National Parks Service (NPS) Best Available Technology (BAT) standard while increasing vehicle dynamic performance with a 50 percent peak power increase over the original equipment version. Engine thermal efficiency has been increased through Late Intake Valve Closure (LIVC) valve timing modification for Miller cycle operation, while high load power was increased through the implementation of a turbocharger and variable electronic boost control. An electronic throttle was also implemented in combination with a “performance/economy” mode switch to limit speed and increase fuel efficiency per the rider's demands.