Search Results

A tire force estimation algorithm is proposed for vehicle dynamic stability control (DSC) system to protect the vehicle from deviation of the normal dynamics attitude and to realize the improved dynamics stability in limited driving conditions. The developed algorithm is based on the theoretical analysis of all the subsystems of the active brake control in DSC system and modulation in DSC, and the robustness is achieved by a compensation method using nonlinear filter in the real time control. The software-in-loop simulation using Matlab/AMEsim and the ground test in the real car show the validation of this method.

Special purpose flat-bed vehicle is commonly utilized to move heavily items such as containers in warehouse, port and other freight handling scene, the hydraulic steering system have be gradually replaced by electric ones. However, the cost of electric steering system is high for commercial activities. Thus, for some corporates, the differential braking steering strategy becomes an ideal alternative. The purpose of this paper is to present a steering control method for flat-bed electric vehicle based on differential braking system. There are two main components of the control method, steering while moving forward and pivot steering, and each of them was composed by upper layer and executive layer. To evaluate the practicability of the control methods, a 7-DOF flat-bed vehicle model was established in Simulink.

Electro-hydraulic power steering system (EHPS) uses the motor as the power source instead of the engine to assist drivers to steer. Compared with traditional hydraulic power steering system (HPS), EHPS system has a better performance in energy saving and driving feeling. In EHPS system, the speed control of the motor determines the performance of the whole system. In this paper, a speed control system of brushless direct current (BLDC) motor based on a Fuzzy-PI controller is established. In addition to the function to adjust speed by adjusting voltage, field weakening is utilized to get a wider speed range, so that the EHPS system has a better performance.

Prototype of a brake-by-wire (BBW) system named Distributed Electro-hydraulic Braking System (DEHB) has been developed. As a BBW system, DEHB is suitable to be used in electric vehicles (EV) and hybrid electric vehicles (HEV). Comparing to the ‘dry’ type distributed BBW systems such as Electro-mechanical Braking System (EMB) or Electric Wedge Brake (EWB), the ‘wet’ feature of DEHB brings benefits to system cost, installation, performance and reliability. In this paper, prototype of the DEHB was described. Based on its ‘wet’ feature, a new fail-safe control for DEHB was proposed. Two types of DEHB architectures that can perform the proposed fail-safe control were described. Superiority of the proposed fail-safe control and architectures for DEHB were examined and verified through simulations and HIL experiments, which helps DEHB to reach a high level of safety and reliability with reduced cost on electro/electronic redundancy.

Based on the study of the dynamic characteristics, the observers for tire force, lateral and longitudinal velocity, and vehicle stability matrix are proposed. The stability matrix is used to predict the stability of the vehicle involving the vehicle dynamic constraints and the active brake pressure modulator. Integrating the proposed method into the state feedback control logic, the predictive control algorithm is brought forward. The simulation results show that the over shoot is restrained and the oscillatory of the steering handling character is overcome.

The performance of Hydraulic Anti-lock Braking System (ABS) is important to vehicle brake safety. In this paper, finite element models and simulation models for studying dynamic response of solenoid valve, a critical part of ABS, are established. Based on the calculation results, which are proved in experiment, several effective methods for improving the performance of the solenoid valve are presented. Furthermore, an ABS-vehicle model is developed to study the influence of hydraulic ABS parameters on braking effect. The simulation results have good agreement with the data of in-vehicle driving experiments.

This paper presents a new magnetorheological braking which can be used in vehicles. Magneto-rheological (MR) fluid is a novel material which can be used in different components of vehicle. Magneto-rheological fluids (MRF) are suspensions of micron size whose yield stress varies rapidly as the change of magnetic field. The use of MRF in vehicles has been gaining popular recently due to its strong rheological effect, fast response and low energy consumption. Besides, these performances give designers more choice in automotive designs. However, most of the related research of MRF brake is about the construction of small prototype to verify its rheological performance. As a result, research progress is limited to calculation and simulation which make the braking force of prototype can hardly meet the requirement of vehicle due to a lack of optimal design and the understanding of MRF in the situation of high sheer stress and magnetic field.

With the advantages of free from engine vacuum, wheel cylinder pressure decoupled from the brake pedal and can be regulated individually and precisely, the brake-by-wire system has a huge application potential in vehicles, especially in electric vehicles (EV) and hybrid electric vehicles (HEV). Electro-hydraulic Brake system is the first approach towards brake-by-wire technology. This paper proposed a new compact EHB, aiming at decreasing the size, volume and cost without compromise of performance. The main components of the proposed EHB are pedal simulator, motor pump, accumulator and eight solenoid valves. An authentic model of the EHB and other key components of the brake system were established based on the test data from the test bench. A control algorithm using Round-Robin scheduling was presented to regulate the fluid pressure. Some parameters of the components were discussed to research their effects on system performance.

The paper presents a new electromechanical brake system for vehicles using magnetorheological fluid. The brake system designed for the electric vehicle has some advantages over the conventional brake system. The brake system is made up of a brake disk, shells, magnetorheological fluid (MRF) and the electromagnets. The brake disk is immersed in the MRF whose yield stress changes as the applied magnetic field. The braking torque of this system can be linearly adjusted by the current in just a few milliseconds without the conventional vacuum booster. This system has a quick response and precise control performance with a low hysteresis. Besides, the system has adopted the original complicated structure to save space and cost. In this paper, the configuration of MRF brake types is described. The braking torques of the MRF brakes is derived based on the MRF theoretical model which is firstly raised. Some braking simulation based on the theoretical model is also shown.

The four-wheel-independent Electro-hydraulic Braking system (4WI EHB) is a wet type Brake-by-Wire system for passenger vehicle and is suitable for electric vehicle (EV) and hybrid electric vehicle (HEV) to cooperate with regenerative braking. This paper gives a review on the design concepts of the 4WI EHB from the following three aspects. 1. Hydraulic architectures. 2. Design concepts of the brake actuator. 3. Installation of the components on the vehicle. Simulations and experiments are carried out to further explore the performance of hydraulic backup and implicit hardware redundancy (IHR). A method to integrate the IHR with hydraulic backup without increasing the total amount of valves is proposed, making the IHR cost and weight competitive. By reviewing various design concepts and analyzing their advantages and drawbacks, a cost and weight competitive design concept of the 4WI EHB with good fail-safe and fault-tolerant performance is proposed.

Many types of brake by wire systems have been developed in past years, such as EMB (Electro-mechanical Brake) [1, 2], DEHB (Distributed Electro-hydraulic Braking System) [3] and EWB (Electric Wedge Brake) [4]. When the vehicle need braking in long period such as waiting for traffic light or downhill braking in those brake systems, the current will sustain very long time with very high level. This current will result in high temperature in motor, and will damage the power supplier. When a new DEHB is developing, a holding function is added in this DEHB. The holding function is self-energized when holding the brake, and automatic released after the brake. Advantageously, after activation of the holding function, the current delivered to the motor for braking is substantially decreased, especially, will be zero when the brake torque is not need to adjust.

Anti-lock Braking System (ABS) is an important control system that can improve the automotive performance, reliability and safety obviously. Hardware-in-the-loop Simulation (HILS) testing is a promising method to assistant design automotive electronics system. In the State Key Laboratory of Automotive Safety and Energy, a HILS system was established to assistant design ABS. The HILS system is composed of a hydraulic control unit of ABS, a normal brake system, a commercial personal computer, a data acquisition card, and several signal-conditioning modules. Powerful software was programmed to perform managing input and output signals, solving 7-freedom and 15-freedom vehicle models, and acquiring response signals of the brake system. Based on the simulations of HILS system, the road experiments with the same conditions of ABS are very necessary and important.

The earth's fossil energy is not limitless, and we should be taking advantage of the highly developed fields of science and technology to utilize it more efficiently and to create a fully environmentally friendly life. Considering the prodigious amount of vehicles in the world today, even a small improvement in their energy-saving performance could have a significant impact. In this paper, a new type of electro-hydraulic power steering (EHPS) system is described. It has two main advantages. First, it can significantly decrease the demand on the motor so that it can be used for a wider range of vehicles. Second, its pressure-flow characteristic can be programmed and is more flexible than hydraulic power steering (HPS) system. A prototype with a 500 W motor was applied to a truck with a front load of 2,700 kg, and static steer sweep tests were conducted to validate its feasibility.