Search Results

In this paper the effect of aerodynamic modifications that influence the unsteady aerodynamic properties of a vehicle on the response of the closed loop system driver-vehicle under side wind conditions is investigated. In today's aerodynamic optimization the side wind sensitivity of a vehicle is determined from steady state values measured in the wind tunnel. There, the vehicle is rotated with respect to the wind tunnel flow to create an angle of attack. In this approach however, the gustiness that is inherent in natural wind is not reproduced. Further, unsteady forces and moments acting on the vehicle are not measured due to the limited dynamic response of the commonly used wind tunnel balances. Therefore, a new method is introduced, overcoming the shortcomings of the current steady state approach. The method consists of the reproduction of the properties of natural stochastic crosswind that are essential for the determination of the side wind sensitivity of a vehicle.

The manufacturers of passenger cars increasingly assign development and production of complete subsystems to the supplying industry. A brake system supplier has to give predictions about system quality and performance long time before the first prototypical system is built or even before the supplier gets the order for system development. Nowadays, the usage of computer-aided system design and simulation is essential for that task. This article presents a tool designed to support the development process. A special focus will be on how to define quality. A formal definition of quality is provided, illustrated and motivated by two examples.

During the acquisition phase brake system supplier have to make predictions on a system's thermal behavior based on very few reliable parameters. Increasing system knowledge requires the usage of different calculation models along with the progress of the project. Adaptive modeling is used in order to integrate test results from first prototypes or benchmark vehicles. Since changes in the brake force distribution have a great impact on the simulation results fading conditions of the linings have to be integrated as well. The principle of co-simulation is used in order to use the actual brake force distribution of the system.

The reliability of electronic components is of increasing importance for further progress towards automated driving. Thermal aging processes such as electromigration is one factor that can negatively affect the reliability of electronics. The resulting failures depend on the thermal load of the components within the vehicle lifetime - called temperature collective - which is described by the temperature frequency distribution of the components. At present, endurance testing data are used to examine the temperature collective for electronic components in the late development stage. The use of numerical simulation tools within Vehicle Thermal Management (VTM) enables lifetime thermal prediction in the early development stage, but also represents challenges for the current VTM processes [1, 2]. Due to the changing focus from the underhood to numerous electronic compartments in vehicles, the number of simulation models has steadily increased.

In 2001 the FKFS (Research Institute of Automotive Engineering and Vehicle Engines, Stuttgart) took into operation state-of-the-art 5-belt systems for road simulation in the 22.45m2-IVK automotive wind tunnel and in the 1.65m2-IVK model wind tunnel. In these systems, a narrow belt running between the vehicles' wheels is fitted with 4 balance-mounted wheel rotation drives and a vehicle restraint system. The FKFS opted for MTS steel belt technology due to its small size, low power requirements and excellent tracking stability. Due to air bearings below the belt, the flat-belt wheel rotation units in the full-scale wind tunnel permit aerodynamic force measurements at full wheel load (8 kN) up to 70 m/s. In combination with the hydrostatic suspension of the units, integrated longitudinal force transducers permit realistic measurements of the wheels' rolling resistance. In the model wind tunnel FKFS wheel rotation units with Poly-V belts are used with small wheel loads up to 80 m/s.

Within in the scope of a road load investigation project at FKFS, the influence of rotating wheels on the road load of a passenger car was investigated. For this purpose an approach was developed to measure the ventilation resistance of a spinning wheel. This approach enables a comparison of different wheel sizes and rim designs. Together with aerodynamic drag measurements in the wind tunnel it is possible to evaluate different wheel configurations with respect to their contribution to the road load. The measuring approach and results of performed measurements are shown in this paper.

In automobile development, wind tunnel measurements are used to optimize fuel consumption and the vehicle's road behavior. The classic measuring technique is based on a stationary vehicle set up in the wind tunnel with stationary wheels. Relative movement between vehicle and road surface is therefore ignored. In more recent studies, measurements have been taken with improved ground simulation. For example, a belt is used instead of the stationary wind tunnel floor and the car wheels rotate. Ground simulation using a belt and rotating wheels generally leads to a reduction in flow angularity at the front wheels, in the same way as blocking the cooling air flow, whereby, as a matter of fact, the aerodynamic drag is reduced. Analogous air flow angle correlations can be established for the effect of underfloor panels.

Automotive engineers use the wind tunnel to improve a vehicle’s aerodynamic properties on the road. However, a car driving on the road does not experience the steady-state, uniform flow characteristic of the wind tunnel. Wind, terrain and traffic all cause the flow experienced by the vehicle to be highly transient. Therefore, it is imperative to understand the effects of forces acting on the vehicle resulting from unsteady flow. To this end, the FKFS swing® installed in the University of Stuttgart’s model scale wind tunnel was used to create 36 different incident flow signals with time-resolved yaw angles. The cD values of five different 25% vehicle models, each with a notchback and a squareback configuration, were measured while under the influence of the aforementioned signals. The vehicle models were chosen to ensure a variety of different geometries, but at the same time also to enable isolated comparison of specific geometric properties.

The unsteady environment road vehicles are exposed to is subject of many investigations that are currently made. Yet, the approaching flow is only one aspect of unsteady forces acting on the vehicle. Unsteady wake structures also lead to time-varying surface pressures and consequently fluctuating forces even in steady and low turbulent flows. However, little is known about the influence of realistic flow conditions, i.e. as found on road, on the unsteady surface pressures and wake structures of a vehicle. Therefore, to derive a deeper understanding of the unsteady aerodynamic properties of a vehicle this paper presents results of measurements conducted on a vehicle body both in smooth and turbulent flow conditions in the IVK model scale wind tunnel. Unsteady surface pressure measurements in the area where separation occurs and the base of the vehicle were made together with time accurate total pressure measurements in the wake.

In addition to the analysis of human driving behavior or the development of new advanced driver assistance systems, the high simulation quality of today’s driving simulators enables investigations of selected topics pertaining to driving dynamics. With high reproducibility and fast generation of vehicle variants the subjective evaluation process leads to a better system understanding in the early development stages. The transfer of the original on-road test run to the virtual reality of the driving simulator includes the full flexibility of the vehicle model, the maneuver and the test track, which allows new possibilities of investigation. With the opportunity of a realistic whole-vehicle simulation provided by the Stuttgart Driving Simulator new analysis of the human’s thresholds of perception are carried out.

This paper introduces a driving-torque measurement method for the determination of vehicle road load and its components. To increase the accuracy, the torque measurements are combined with rolling resistance measurements performed with a specially developed trailer. This method is a strictly experimental approach and does not use any mathematical models. The experimental techniques are described as well as the proceedings to compare test stand and road measurements. The results that are shown prove that this method is suitable for the investigation of single road load components. Furthermore, the comparison of different rolling resistance measurement devices shows the potential of the measurement trailer and the necessity to perform rolling resistance measurements on real road surfaces and not solely on test stands.

The combination of enhanced powertrains and adapted vehicle concepts can reduce the energy demand of vehicles significantly, especially when energy conversion efficiency rises and at the same time driving resistances decrease. In addition, new powertrain concepts are able to offer extra functionality due to a growing cross-linking with chassis and vehicle body. The design of highly linked vehicles and powertrain systems requires additional new development methods in order to answer interacting questions of driving dynamics and vehicle energy efficiency at an early stage of development. In the paper a database-based simulation platform is presented which was developed at the IVK of the University of Stuttgart in cooperation with the Research Institute of Automotive Engineering and Vehicle Engines Stuttgart (FKFS). The simulation platform is used as an example to discuss mass reducing developments for various powertrain concepts.

This paper deals with the correction for interference effects on the flow about bluff bodies in open-jet wind tunnels. Altogether, five different interference effects in open-jet tunnels are identified and described by physical models. Besides the classical jet-expansion correction which has been treated repeatedly by various authors throughout the last 60 years, the new correction method also includes the effect of jet deflection due to the proximity of a vehicle to the nozzle. Furthermore, far-field interference effects originating from the nozzle and the collector are described. For this purpose nozzle and collector effects are treated as solid- wall blockage phenomena, and with the aid of Biot-Savart principles the induced velocity at the model position is calculated. Finally, the static- pressure gradient in an empty test section generates a horizontal buoyancy force when a model is placed in a wind tunnel stream.

In the digital prototype development process of a new Mercedes-Benz, thermal protection is an important task that has to be fulfilled. In the early stages of development, numerical methods are used to detect thermal hotspots in order to protect temperature sensitive parts. These methods involve transient full Vehicle Thermal Management (VTM) simulations to predict dynamic vehicle heat-up during critical load cases. In order to simulate thermal control mechanisms, a coupled 1D to 3D thermal vehicle model is built in which the coolant and oil circuit of the engine, as well as the exhaust flow are captured in detail. When performing a transient 3D VTM analysis, the conduction and radiation phenomena are simulated using a transient structure model while the convective phenomena are co-simulated in a steady state fluid model. Both models are brought to interaction at predetermined points by an automatized coupling method.

The entire automotive industry is moving towards lower CO₂ emissions and higher energy efficiency. Especially for higher driving speeds this can be achieved by minimizing aerodynamic drag. Additionally, aerodynamic downforce is essential to maintain or even improve the handling performance of a vehicle. In order to optimize the vehicle's aerodynamic efficiency in wind tunnel tests, the boundary conditions of a vehicle driving on a road must be simulated properly. Particularly for optimizing the underbody region of a vehicle, ground simulation is an important issue in every wind tunnel. Today rolling road systems featuring one or more moving belts on the wind tunnel floor are a standard tool to simulate the complex boundary condition of a vehicle driving on the road. But generally the technical effort to measure aerodynamic forces accurately increases with improvement of the aerodynamic ground simulation.

In recent years, driving simulators have become a valuable tool in the automotive design and testing process. Yet, in the field of vehicle dynamics, most decisions are still based on test drives in real cars. One reason for this situation can be found in the fact that many driving simulators do not allow the driver to evaluate the handling qualities of a simulated vehicle. In a driving simulator, the motion cueing algorithm tries to represent the vehicle motion within the constrained motion envelope of the motion platform. By nature, this process leads to so called false cues where the motion of the platform is not in phase or moving in a different direction with respect to the vehicle motion. In a driving simulator with classical filter-based motion cueing, false cues make it considerably more difficult for the driver to rate vehicle dynamics.

The geometric shape of the tires can have a large influence on the aerodynamic drag of a passenger car as it has been shown already in different publications like for example [1, 2, 3]. However, to optimize the shape of a tire, nowadays quite some effort is needed in terms of wind tunnel time and costs for prototype tires. In this paper an approach to optimize the tire's shape in model scale is described, which can help to reduce both development time and costs. The first step in the development of this method was to verify that the aerodynamic effects of the tire geometry in model scale are comparable to full scale tests. This was achieved by measuring different production tires in full scale and also by measuring the quarter scale version of the same tires. The only difference between the original and the model scale tires was that the scaled tires were not deformable. The results show that the difference between two sets of tires is comparable in full scale and in quarter scale.

This paper presents some recent results concerning the generation and minimization of cooling air drag, achieved in an integrated approach of numerical and experimental investigations. The baseline configuration of a production cars' cooling air flow system is analyzed. The analysis of the created drag shows, that most of the force changes due to the cooling air flow appear in the front region of the vehicle. However, the forces generated by heat exchangers are only a small share of the total changes. Additional drag is generated for example by the front wheels and by the components of the underhood compartment. The investigation of the influence of the vehicle rear end shape on the aerodynamics of the cooling air flow system shows, that two similar cars with different rear end shapes (notchback and squareback) can feature different cooling air drag values.

In this paper the influence of different turbulent flow conditions on the aerodynamic drag of a quarter scale model with notchback and estate back rear ends is investigated. FKFS swing® (Side Wind Generator) is used to generate a turbulent flow field in the test section of the IVK model scale wind tunnel. In order to investigate the increase in drag with increasing yaw, a steady state yaw sweep is performed for both vehicle models. The shape of the drag curves vary for each vehicle model. The notchback model shows a more pronounced drag minimum at 0° yaw angle and experiences a more severe increase in drag at increasing yaw when compared to the estate back model. Unsteady time averaged aerodynamic drag values are obtained at two flow situations with different turbulent length scales, turbulence intensities, and yaw angle amplitudes. While the first one is representing light wind, the second one is recreating the presence of strong gusty wind.

This paper presents an integrated numerical and experimental approach to take best possible advantage of the common development tools at hand (1D, CFD and wind tunnel) to determine the cooling air mass flow at the different vehicle development stages. 1D tools can be used early in development when neither 3D data nor wind tunnel models with detailed underhood flow are available. A problem that has to be resolved is the dependency on input data. In particular, the pressure coefficients on the outer surface (i.e. at the air inlet and outlet region) and the pressure loss data of single components are of great importance since the amount of cooling air flow is directly linked to these variables. The pressure coefficients at the air inlet and outlet are not only a function of vehicle configuration but also of driving velocity and fan operation. Both, static and total pressure coefficient, yield different advantages and disadvantages and can therefore both be used as boundary conditions.