Refine Your Search

Search Results

Viewing 1 to 9 of 9
Technical Paper

Study on the Filter Structure of SiC-DPF with Gas Permeability for Emission Control

2005-04-11
2005-01-0578
The pore structure of DPF (Diesel Particulate Filter) is one of the key factors in contributing the fuel consumption and the emission control performance of a vehicle. The pressure loss of mini samples (1 in. in diameter, 2 in. in length) with various pore structures was measured at relatively low filtration velocity (< 5 cm/sec). Then the obtained data were evaluated by using an index of “permeability”. As a result, among the parameters which characterize the pore structure, it was found that the size of the pore diameter and the sharpness of pore distribution were the most contributing factors in reducing pressure loss which in turn is related to the fuel consumption performance when the cell structure was fixed. On the other hand, it was found that the gas permeability was not affected significantly by any parameter when the catalyst was coated because the coating caused a broadening of the pore distribution.
Technical Paper

Study on Filter Substrate Structure for Lower Backpressure and Higher Regeneration Performance

2006-04-03
2006-01-1526
The trade-off between NOx and particulate matter (PM) has been a technological challenge with respect to diesel engine emissions. However, the practical use of diesel particulate filters (DPF) has made diesel emission control possible, in which NOx emissions are reduced through engine control and nearly all emitted PM is completely removed by DPF from diesel exhaust emissions. This has helped to contribute to laying the foundation for pursuing of the high theoretical thermal efficiency of diesel engines. However, it is also a fact that such emission controls have resulted in considerable impairments on the original and greatest advantages of diesel engines. This includes fuel penalties with accompanying increases in fuel consumption caused by pressure losses due to the attachment of the DPF itself and the accumulation of PM in the DPF, as well as fuel losses that occur when fuel is used to regenerate collected PM.
Technical Paper

Study on Catalyzed-DPF for Improving the Continuous Regeneration Performance and Fuel Economy

2007-04-16
2007-01-0919
It is a big challenge how to satisfy both the purification of exhaust gas and the decrease of fuel penalty, that is, carbon-dioxide emission. Regarding the Diesel Particulate Filter (DPF) applied in the diesel after-treatment system, it must be effective for lowering the fuel penalty to prolong the interval and reduce the frequency of the DPF regeneration operation. This can be achieved by a DPF that has high Particulate Matter (PM) mass limit and high PM oxidation performance that is enough to regenerate the DPF continuously during the normal running operation. In this study, the examination of the pore structure of the wall of a DPF that could expand the continuous regeneration region in the engine operation map was carried out. Several porous materials with a wide range of pore structure were prepared and coated with a Mixed Oxide Catalyst (MOC). The continuous regeneration performance was evaluated under realistic conditions in the exhaust of a diesel engine.
Technical Paper

Soot Oxidation Kinetics in Diesel Particulate Filters

2007-04-16
2007-01-1129
Direct catalytic soot oxidation is expected to become an important component of future diesel particulate emission control systems. The development of advanced Catalytic Diesel Particulate Filters (CDPFs relies on the interplay of chemistry and geometry in order to enhance soot-catalyst proximity. An extensive set of well-controlled experiments has been performed to provide direct catalytic soot oxidation rates in CDPFs employing small-scale side-stream sample exposure. The experiments are analyzed with a state-of-the-art diesel particulate filter simulator and a set of kinetic parameters are derived for direct catalytic soot oxidation by fuel-borne catalysts as well as by catalytic coatings. The influence of soot-catalyst proximity, on catalytic soot oxidation is found to be excellently described by the so-called Two-Layer model, developed previously by the authors.
Technical Paper

Soot Loading Estimation Accuracy Improvement by Filtration Layer Forming on DPF and New Algorithm of Pressure Loss Measurement

2013-04-08
2013-01-0525
A diesel particulate filter (DPF) is a key component for reduction of engine soot emission. The soot collected in the DPF is periodically burned off, so-called DPF regeneration, and a behavior of the pressure drop increased by the soot loading is generally utilized to estimate the amount, which must be a trigger of the regeneration. However, it is said that the estimation of the soot loading amount has considerable dispersion caused by two main reasons. One is hysteresis of the transient pressure drop resulted from the combination of so-called deep-bed and cake filtration modes. The other is a fluctuation of exhaust gas temperature and flow rate as well as a pulsation from the engine. In this study, the accurate estimation method of the soot amount accumulated in the DPF was proposed in combination with filtration layers (FLs) technology and a new algorithm based on fast Fourier transform (FFT) technology.
Technical Paper

Further Experimental Study of Asymmetric Plugging Layout on DPFs: Effect of Wall Thickness on Pressure Drop and Soot Oxidation

2015-04-14
2015-01-1016
In order to guide the development of asymmetric plugging layout Diesel Particulate Filters, hereafter referred to as “VPL-DPF”, in this paper we present some evaluation results regarding the effect of design parameters on the VPL-DPF performance. VPL-DPF samples which have different wall thicknesses (thin and thick walls) were evaluated in regards to their pressure drop and soot oxidation behaviors, with the aim to optimize the design of DPF structure. As a result of pressure drop evolution during soot loading, contrary to our expectation, in some cases, it was found out that VPL increases the transient pressure drop compared to the conventional plugging layout DPF. That meant there is an appropriate specific optimum wall thickness for adoption of VPL which has to be well defined at its structural design phase. Based on our previous research, it is expected that this result is due to interactions among the different (five) wall flows that exist in a VPL-DPF.
Technical Paper

Feasibility Study on the Filter Design of Re-Crystallized SiC-GPF for TWC Coating Application

2015-04-14
2015-01-1011
The Particle Number (PN) emission limit is implemented for Direct Injection (DI) gasoline from EU6 regulation in European region. The wall-flow type ceramic filter technology is an essential component for Diesel PN emission control, and will be one potential solution to be investigated for the future Gasoline DI PN emission control demand. Especially the requirement of lower pressure loss with smaller filter volume is very strong for the filter substrate for Gasoline DI compared to DPF, not to lose better fuel economy benefit of Gasoline DI engine. Re-crystallized SiC (R-SiC) has high strength as its own property, and enable for Gasoline Particulate Filter (GPF) design to make the wall thickness thinner and the porosity higher compared to the other ceramic materials.
Technical Paper

Durability of Filtration Layers Integrated into Diesel Particulate Filters

2013-04-08
2013-01-0837
This paper describes the durability of the filtration layer integrated into Diesel Particulate Filters (DPFs) that we have developed to ensure low pressure loss and high filtration efficiency performances which also meet emission regulations. DPF samples were evaluated in regards to their performance deterioration which is brought about by ash loading and uncontrolled regeneration cycles, respectively. Ash was synthesized by using a diesel fuel/lubrication oil mixture and was trapped up to a level which corresponded to a 240,000km run, into the DPFs both with and without the filtration layer. Afterwards, aged-DPFs were measured with respect to their permeability, pressure loss, filtration efficiency, as well as soot oxidation speed using suitable analytical methods. Consequently, it has been confirmed that there was no noteworthy deterioration of the performances in the DPF with the filtration layer.
Technical Paper

Development of High Porosity SiC-DPF Which is Compatible with High Robustness and Catalyst Coating Capability for SCR Coated DPF Application

2013-04-08
2013-01-0840
Diesel emission regulation becomes stringent more and more regarding both particulate matter (PM) and NOx in the worldwide. SCR coated DPF system is considered as one of the promising options for future diesel exhaust after-treatment because it has several benefits such as the downsizing of the system, quick light-off of the catalytic function due to mounting closed-couple position. To integrate the SCR converter into the DPF, it is necessary to design the DPF substrate's porosity higher and pore size larger than conventional DPF to improve SCR catalyst coating capability. However to make the porosity higher will lose the robustness in general. Against these problems, it was studied to improve the high porosity DPF performances by applying the new technology to modify the thermal shock resistance property.
X