Search Results

The present work proposed to implement oxy-fuel combustion mode into a homogeneous charge compression ignition engine to reduce complexity in engine emissions after-treatment and lower carbon dioxide emission. The combination of oxy-fuel combustion mode with homogeneous charge compression ignition engine can be further optimized by the utilization of direct high temperature and pressure water injection to improve cycle performance. A retrofitted conventional diesel engine coupled with port fuel injection and direct water injection is utilized in this study. A self-designed oxygen and carbon dioxide mixture intake system with flexible oxygen fraction adjustment ability is implemented in the test bench to simulate the adoption of exhaust gas recirculation. Water injection system is directly installed in the combustion chamber with a modified high speed solenoid diesel injector.

In this study, a spray hot-impingement system was set up to analyze the spray characteristics when spray impinged onto a flat hot surface by high-speed photography technology. The angle between spray axis and normal line of the flat surface could be changed, and the surface temperature could exceed 400°C. The influences of surface temperature and heating power on spray atomization were investigated too. At atmospheric pressure, when the wall temperature was 340∼380°C, the impinging diesel spray was well atomized. In this experiment, the wall heating power could be set at 1∼25 Wcm-2. When the heating power was about 1.6 Wcm-2, the impinging spray atomized well, and when it was about 10.1 Wcm-2 the spray atomized better though the heating power requirement should be high.

The argon power cycle engine, which uses hydrogen as fuel, oxygen as oxidant, and argon other than nitrogen as the working fluid, is considered as a novel concept of zero-emission and high-efficiency system. Due to the extremely high in-cylinder temperature caused by the lower specific heat capacity of argon, the compression ratio of spark-ignition argon power cycle engine is limited by preignition or super-knock. Compression-ignition with direct-injection is one of the potential methods to overcome this challenge. Therefore, a detailed flammability limit of H2 under Ar-O2 atmosphere is essential for better understanding of stable autoignition in compression-ignition argon power cycle engines.

Based on a 125cm3 single cylinder SI engine, the designated idle speed was controlled by adjusting of cycle ignition advance angle. By analyzing the effects of different idle speed and throttle open position on three way catalyst (TWC) light-off time and conversion efficiency of HC and CO emissions, combined with the corresponding total HC and CO emissions level, the optimum idle speed and throttle open position at engine's warm-up phase were found by the matching optimum. The present method for engine control strategy is helpful to optimize the warm-up phase emission levels in SI engine with LPG fuel.

A segment of steel tube with the inner diameter of 60 mm and length of 100 mm was fixed between the intake manifold and cylinder head in a direct injection natural aspirated diesel engine. The surface of the tube could be heated to be above 400 °C by the heater enwrapped outside within several minutes under the power less than 600 W. The tip of an injector traditionally used for in-cylinder diesel direct injection was extended to the axis of the tube. The diesel sprays could impinge onto the hot inner surface of the tube and atomize quickly if the temperature of the tube was high enough. Then the fuel-air mixture would be sucked into the cylinder, and HCCI combustion could be fulfilled. The vaporization ratio of the impinged diesel sprays was estimated by fuel consumption, intake air flux and excess air coefficient (λ) calculated from the volumetric concentration of O2, CO2 and CO emissions. The NOx emission was always very low.

Gasoline homogeneous charge compression ignition (HCCI) can achieve high efficiency and extremely low NOX emissions. However, the working condition range of HCCI is limited by knock occurring during engine operation. To achieve an expanded HCCI working condition range, it is necessary to explore a method predicting knock cases accurately to avoid knock occurring. Based on a DI-HCCI engine with ethanol/gasoline mixed fuel, the knock cases under different conditions have been investigated. In-cylinder pressure signals are used to identify the knock cases and the knock oscillations are extracted with fast Fourier transform (FFT). The effects of the ethanol proportion in the fuel and air/fuel ratio on the characteristics of knock have been studied. The results have shown that the knock parameters, such as maximum frequency, start point angle and the duration, have close relationship with the knock intensity.

Homogeneous Charge Compression Ignition (HCCI) combustion has the characteristics of high efficiency and low emissions. However, the lack of a decisive control method of combustion timing hinders its application. In this paper, the effects of fuel injection strategies on HCCI combustion and ion current (IC) characteristics were studied experimentally and numerically. The results show that by advancing the fuel injection timing or increasing the fuel injection ratio during negative valve overlap (NVO), the combustion phase and the start of ion current in the main combustion are both advanced, and the strength of the IC signal during NVO is enhanced as well, indicating that more active species will lead to earlier combustion. Additionally, HCCI combustion is determined not only by the reforming of fuel composition in NVO but also by the distribution of mixture and the gradient of concentration in the cylinder.

Ion current sensing, which usually employs a spark plug as its sensor to obtain feedback signal from different types of combustion in SI engines, may be applied to HCCI combustion sensing instead of a prohibitively expensive piezoelectric pressure transducer. However, studies showed that the ion current detected by a spark plug sensor is a localized signal within the vicinity of the sensor's electrode gap, being affected by conditions around it. To find out better and feasible ion probe positions, a 3D-CFD model with a detailed surrogate mechanism containing 1423 species and 6106 reactions was employed to study the effect of stratification on ion distribution in HCCI combustion. The simulation results indicate that the monitor probe 1, 8 and 9 are more stable and reliable than the others. IONmax and dIONmax are more accurate to estimate CA50 and dQmax respectively.

This paper presents the development of an electronic control LPG gas injection system and its application in a small SI engine. The tests results show that the developed LPG gas injection system can meet the needs for the goal of high engine power output and low exhaust emissions based on the engine bench tests. With the LPG electronic gas injection system, the air-fuel ratio can be optimized based on the requirements and CO and NOx emission levels are decreased significantly compared with the LPG mechanical mixer fuel supply system, based on the same HC emission levels. With the new gas phase LPG electronic control injection system, the HC emission level is controlled below the 300 ppm under most engine conditions and under 200 ppm when the engine speed is over 3000 r/min. The NOx emission level is under 2600 ppm in the whole range of engine operation conditions and is decreased by 2000 ppm compared with the LPG mechanical mixer system.

An air-cooled, four-stroke, 125 cc electronic gasoline fuel injection SI engine for motorcycles is altered to burn ethanol fuel. The effects of nozzle orifice size, fuel injection duration, spark timing and the excess air/ fuel ratio on engine power output, fuel and energy consumptions and engine exhaust emission levels are studied on an engine test bed. The results show that the maximum engine power output is increased by 5.4% and the maximum torque output is increased by 1.9% with the ethanol fuel in comparison with the baseline. At full load and 7000 r/min, HC emission is decreased by 38% and CO emission is decreased 46% on average over the whole engine speed range. However, NOx levels are increased to meet the maximum power output. The experiments of the spark timing show that the levels of HC and NOx emission are decreased markedly by the delay of spark timing.

This paper presents an experimental study of the emission characteristics of a small Spark-Ignited, LPG engine. A single cylinder, four-stroke, water-cooled, 125cc SI engine for motorcycle is modified for using LPG fuel. The power output of LPG is above 95% power output of gasoline. The emission characteristics of LPG are compared with the gasoline. The test result shows that LPG for small SI engine will help to reduce the emission level of motorcycles. The HC and CO emission level can be reduced greatly, but NOx emissions are increased. The emission of motorcycle using LPG shows the potential to meet the more strict regulation.

Based on high EGR rate, the low temperature combustion (LTC) has been studied widely, of which the application range is more extensive than the homogeneous charge compression ignition (HCCI) and premixed charge compression ignition (PCCI). As the high EGR rate would influence the condition of intake charge, it would also affect the combustion process and the HC emissions, thus the combustion stability of LTC would be lower than tradition diesel combustion. In this study, an ion current detecting technology was employed to explore the ion current at different EGR rates. Meanwhile, the combustion parameters were also investigated, which included the in-cylinder pressure and heat release rate. The CA50 and CAI50 were adopted as the phases of combustion and ion current, which respectively represented the crank angle of mid-point for the integrated heat release and integrated ion current. Then the correlation between CA50 and CAI50 was analysed.

Gasoline direct injection (GDI) technology is admitted to be one of the most effective measures to improve the fuel economy for the spark ignition (SI) engines. Homogeneous Charge Compression Ignition (HCCI) combustion has advantages of low fuel consumption and ultra low NOx emissions. But the difficulty in the autoignition control and the narrow operation region inhibit the practical application of this technology. A hybrid combustion mode which combines SI mode and HCCI mode in separated working regions was regarded as a promising technology for HCCI engines. In addition, monitoring and providing feedback to the in-cylinder combustion characteristics is generally considered to be an effective method to improve and to optimize the combustion process. A lot of combustion information is included in the ion current generated by the in-cylinder combustion, and hence the ion current detection technique is considered to be a potential combustion feedback method.

The effectiveness of after-treatment systems depends on the exhaust gas temperature, which is low during cold-start. As a result, Euro III, Euro IV and FTP75 require that the emissions tests include exhaust from the beginning of cold start. It is proved that 50%∼80% of HC and CO emissions are emitted during the cold start and the amount of unburned fuel from the crevices during starting is much higher than that under warmed engine conditions. The piston crevices is the most part of combustion chamber crevices, and results of mathematical simulations show that the piston crevice contribution to HC emissions is expected to increase during cold engine operation. Based on the transient HC test data and the double zone combustion model, this paper presents the study of the crevice HC Mechanism of the first firing cycle at cold start on an LPG SI Engine. A fast-response flame ionization detector (FFID) was employed to measure transient HC emissions of the first firing cycle.