Search Results

The paper presents the main reasons for the increasing market share of vehicles with the capacity to run on random bio fuel blends. It describes the philosophy and basic layout of current integral flex mixture preparation systems. The paper demonstrates the necessity to introduce a series of new high-performance analysis tools for further improvement of the mixture preparation system and in particular the fuel injector performance. The paper continues with a discussion of the basic structure of the interactive Virtual Engine Model approach applied to fuel injector atomizer optimization. Test results obtained by application of the new tools to two different series production flex engines are presented. The impact of the improved spray formation capability of the optimized fuel injector atomizers is explained and experimental vehicle FTP-cycle data are reported and discussed.

The paper presents a study of the influence of fuel pressure supply fluctuations on the upstream side of the fuel injector atomizer. The study is performed over a wide range of pressures (70 to 130 Mpa) with two different common-rail (CR) high-pressure fuel injectors. The common atomizer is a VCO-type equipped with conically shaped atomizer bores. With the injector tip (nozzle) mounted in a counter-pressure vessel the pressure fluctuations in the fuel-rail and in the injector body are recorded simultaneously with stroboscopic Schlieren-visualization of the time-resolved spray behavior. It is demonstrated that not only the instantaneous mass flow is affected. As a function of rail-pressure, pulse-width and injection strategy the pressure fluctuations change the spray hard-core structure and its break-up behavior.

The paper presents a study of a key-element in the mixture preparation process. A typical common-rail (CR) high-pressure fuel injector was fitted with a prototype injector nozzle with atomizer bores of a particular conical layout. It is demonstrated within certain layout limits, that a considerable enhancement can be obtained for the secondary break-up of the hard-core fluid sprays produced by the nozzle. The impact on the combustion process is examined in terms of pressure and heat release as well as of the engine-out pollutant emission. The results are compared to those of an earlier developed CR high-pressure injector nozzle. The atomization behavior of the prototype nozzle is illustrated through experimental results in terms of engine-out emissions from a 1.3-liter turbo-charged passenger car diesel engine. The detailed spray behavior is visualized on a component test rig by use of specially developed optical visualization techniques.

In the present paper the impact of three different geometrical layouts of the discharge nozzle of a high-pressure diesel injector designed is examined for a common rail second generation direct injection system. The paper presents a comparative study of the spray behavior of the three different nozzle layouts connected to a 150 MPa rail-pressure when mounted on a 1.6 liter European passenger car engine. To evaluate experimentally the differences in the fundamental physical spray parameters several specially developed optical visualization techniques are used, which enable phase-Doppler, Laser-sheet and high-speed recordings of dense high pressure sprays. The change in basic spray parameters (time-resolved droplet distribution and spray momentum) caused by the nozzle geometry variation is examined. The impact on the in-cylinder penetration and mixing characteristics is studied with a 3D-numerical simulation code NCF-3D.

In the present paper are examined the consequences of a substantial rise in the injection pressure for Gasoline Direct Injection (GDI) injector assemblies. The paper presents a comparative study of the spray behavior of two different injector nozzle layouts submitted to current 10 Mpa rail-pressure as well as to a 30 Mpa injection pressure. To evaluate the differences in the fundamental physical spray parameters are used several specially developed optical visualization techniques, which enable phase-Doppler, PIV, Laser-sheet and high-speed recordings of dense high pressure fuel sprays. A recently developed injector actuator and the necessary modifications to existing high-pressure pumps to reach a 30 MPa pressure level in the fuel system are presented. The change in basic spray parameters (time-resolved droplet distribution and spray momentum) caused by the rail-pressure rise is examined.

The paper describes the application of laser sheet flow visualisation with numerical image analysis as a useful complementary tool to numerical simulation techniques for the optimisation of fluid dynamics within SI-engine in-take systems. The lay-out of the laser sheet visualisation system and the applied numerical image analysis are discussed in detail. Two applicative examples are given, one of smoke induced visualisation of the internal gas flow of an intake manifold, the other of natural visualisation of fuel injector wall film deposit in the intake runner. Finally is concluded that the addition of visualisation techniques to the development strategy allows a time gain, because it contributes to a rapid understanding of complex flow phenomena.

The paper presents a description of the development phases of the new third generation of “green” fuel injectors. The development objective for the new PICO-ECOlogical injector was to define a layout, which enables an optimal parameter configuration for both the mixture preparation (high flexibility to adapt different atomizer plate structures) and the manufacturing processes. It is demonstrated in which way the use of high-level numerical simulation and visualization techniques have become an integrated part of the development process. A detailed description is given of the new layout with respect to earlier versions and the advantageous new features obtained are discussed. Test results obtained by the new 3rd-generation injector layout are presented. The impact of the improved dynamic response capability is explained and experimental data at both engine test rig and vehicle FTP-cycle conditions are reported and discussed.

The paper describes the setup of a 4-cylinder 1.4-liter prototype Spark Ignited (SI)-engine, which is highly boosted, extremely downsized and port fuel injected. During experimental data gathering with the engine it was discovered that the originally mounted fuel injectors were non-optimized an unable to produce an expected low fuel consumption performance at low speed, low load engine working conditions. To solve this problem by finding an optimized alternative solution for the mixture preparation process it was decided to use a high-performance numerical simulation tool. The paper presents the overall layout of the prototype engine as well as the structure of the 3-D dynamic optimization tool used to address the mixture preparation problem. The paper continues with a detailed description of the different steps used to reach the complete optimization of the mixture preparation system (both the fuel injectors and the intake manifold).

The paper gives a short introduction to the bio-diesel mixture approach for diesel engines. The paper continues with a description of the design of a strategy for recognition of a random bio-diesel fraction, Bx, by a purely software-based sensing technique, which creates an image of the temporal combustion behavior and uses only sensors already in service for current common rail mixture preparation systems. A short description is made of a baseline approach of sensing technique based on the presence of a crank angle speed sensor. Hereafter the paper presents the introduction of several integral or Upper Level (UL) key-parameters used to enhance the precision of the Bx-detection or completely replace the original lower level combustion key-parameter set, which relates the instantaneous fraction of bio-diesel, Bx, to the engine torque.

The present paper describes a study, which can enable a small displacement (1.3 liter) turbocharged European CR-diesel engine to tolerate an important increase in EGR-level. The analysis is performed by use of a 3D virtual numerical engine model, which isolates the main parameters that must be optimized within the perimeter of the combustion chamber. The paper gives a short introduction to the physical background for NOx and soot-formation as well as a recall of the main issues related to the simulation models used in the virtual engine simulation. The analysis is performed in a 9 points load/speed test matrix. Several EGR-rates are studied as well as the impact of a precise temperature control of the exhaust gas re-introduced in the intake manifold. The paper concludes by an analysis of the cumulated impact on the EGR-level tolerated by the engine after the introduction of the suggested optimization measures.

The paper presents a short introduction on the evolution from the first generation of software based flex fuel sensor systems over the second system generation including new gasoline/ethanol optimized fuel injectors to the 3rd generation, which combines all available optimized mechanical components. It demonstrates that to meet the new emission regulations and On Board Diagnostic requirements a new highly flexible Electronic Control Unit (ECU) is needed. A detailed description of the new powerful, layered-structure ECU-family is given. The paper concludes with some illustrative experimental results obtained by combining the new ECU-family with engine-layout optimized mechanical components.

The paper presents the background research on the physics of the droplet coalescence phenomena carried out by an interactive usage of high-level 3-D numerical simulation tools and high-level optical visualization and measurement techniques. The presentation continues with the description of a new injector atomizer plate layout, which enables a physical coalescence control of the droplet population within the entire fuel spray. Finally are presented examples of the impact on exhaust emissions of the introduction the new atomizer plate with coalescence control by engine test bed experiments (steady state low load conditions) and vehicle tests (first cold part of the FTP-cycle).

The paper describes the optimization to match the Brazilian market requirements for a Flex-Vehicle of the intake system and in particular the fuel injectors of a small displacement (1.6 l) 8 valves passenger car engine. The imposed target was to find a compromise for the hardware components related to the mixture preparation process, which optimize their performance with respect to a gasoline with a random content (from 0 to 100 %) of ethanol. The analytical optimization process is performed by use of a 3-D numerical virtual engine in which can be studied the physical phenomena of spray atomization, vaporization and momentum fluctuations from different injector atomizer layouts. The different atomizer layouts as well as several vaporization enhancement approaches are rated with respect to a baseline configuration on the virtual engine. The paper presents the results obtained by highest rated solutions, which were manufactured as prototypes and tested on the real engine.

The present paper describes a study of the basic parameters, which govern particulate (soot) formation within the combustion chamber of a small displacement (1.3 liter) turbocharged European CR-diesel engine. The main tools used for the study are a real fired engine, a numerical virtual engine and a special high ambient pressure vessel for injector spray visualization. The paper describes an improved soot formation model implemented in the virtual engine setup. A comparison is presented between measured and computed combustion data at 8 different load points. The paper concludes with a discussion of the means, which can be used to minimize the particulate matter formation in the design phase of both the combustion layout and the fuel injector atomizer as well as in the design of the injection control strategies.

The success obtained by use of Virtual Engine Modeling (VEM) in the design and development areas of fuel injectors generated a lot of interest from production and quality engineers to dispose of a similar tool related to spray vessel measurements. To respond to stringent PL6/EURO5 requirements it was decided to develop a Virtual Spray Vessel (VSV) tool capable of predicting spray patters and perform droplet diameter analysis comparable to Phase Doppler Analysis (PDA) results. The paper describes the analogies between VEM and VSV modeling, the specific new numerical approaches to obtain spatial spray data comparable to conventional mechanical measurement techniques and to perform droplet diameter analysis comparable to PDA data. The paper concludes with a series of comparisons of simulated and experimental data.

The suggestions for upcoming Euro 2000 clean air act puts an increasing legislative pressure for lower specific fuel consumption in order to reduce the emission of CO2 and thereby decrease the impact of the “green house” effect. One of the possible suggestions to meet these requirements for SI-engines is the gasoline direct injected (GDI) power unit. One of the key points of the success of a layout of a GDI system is the optimization of the fuel injector and combustion chamber charge formation parameters. A brief description of the basic GDI-system used during the study is given. Hereafter are outlined the computational and experimental optimization tools which have been used to produce, on a reasonable industrial time scale, the main indications to optimize the design of a given injector/chamber configuration. The paper discusses in detail the results produced by the latest enhancements introduced into the 3D multi-phase computational approach, NCF-3D.

Experimental measurements and numerical computations were made to characterize a spray generated by a high-pressure swirl injector. The Phase Doppler technique was applied to get information on droplet sizes (d10) and axial velocities at defined distances from the injector tip. Global spray visualization was also made. Computations were carried out using a modified version of KIVA 3V. In particular, the break-up length of the sheet and its dimension were computed from a semi-empirical correlation related to the wave instability theory suggested by Dombrowski, including the modifications introduced by Han and Reitz. Two different approaches were used to describe the initial spray conditions. According to the first, discrete particles with a characteristic size equal to the thickness of the sheet are injected. The second approach assumes, that the particles having a SMD computed by a semi-empirical correlation are injected according to a statistical distribution.

The first part of the paper gives an overview of the environmental conditions with which a future two stroke powered vehicle must comply and explains the reasons for which a direct gasoline injection into the combustion chamber offers a potential solution. The paper continues with a description of the fuel/air mixture injection used in the F.A.S.T. concept and gives a detailed overview of the layout of the 125 cc engine to which it is applied. The structure of its electronic engine management system, mandatory for the necessary control precision, is presented. Hereafter is made a short introduction to the visualization and numerical computation tools used for the engine design optimization. The paper concludes with a detailed presentation and discussion of the experimental results obtained with the engine operated, either in steady state and transient conditions on an engine test rig, and mounted in a classic small dimension two-wheel vehicle submitted to road tests.

The first part of the paper gives an overview of the current development status of the GDI system layout for the middle displacement engine, typically 2 liter, using the stoichiometric or weak lean concept. Hereafter are discussed the particular requirements for the transition to a small displacement/small bore engine working in stratified lean conditions. The paper continues with a description of the application of the different steps of the optimization methodology for a 1.2 liter, small bore 4 cylinder engine from its original base line MPI version towards the lean stratified operation mode. The latest changes in the combustion model, used in the numerical simulation software applied to the combustion chamber design, are discussed and comparison made with the previous model. The redesign of the combustion chamber geometry, the proper choice of injector atomizer type and location and the use of two-stage injection and multi-spark strategies are discussed in detail.

The first part of the paper gives an overview of the current results obtained with the first-generation of GDI-powered vehicles launched on the European market. In view of the rather limited success in fuel consumption gain the second-generation of very lean stratified layouts has begun, but this process requires the development and application of new high-level analysis tools. A possible high performance approach is the multi-purpose use of 3-D numerical simulation both in the development and the engine control strategy calibration phases. The development of a small 1.6 liter lean stratified engine project was chosen to demonstrate the dual application capability of the NCF-3D simulation tool. The paper continues with a description of the engine application frame, the basic features of the NCF-3D simulation tool and the latest enhancements made to combustion and fuel composition models within the software frame.