Refine Your Search

Search Results

Standard

Rated Operating Load for Loaders Equipped with Log or Material Forks Without Vertical Mast

2011-10-27
CURRENT
J1197_201110
This SAE Recommended Practice applies to wheel and crawler loaders when equipped with log or material handling forks without vertical masts, taking only hydraulic lift capacity and operating stability into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions would require more careful or restricted operation with the rated operating load. This practice is not to be construed as setting up test procedures or conditions.
Standard

Metric Countersunk Holes for Cutting Edges and End Bits

2011-10-27
CURRENT
J1580_201110
this document is to be used on cutting edges and end bits in conjunction with metric bolts (reference ISO 7852-1982) typically used on off-road, self-propelled work machines as described in SAE J1116. The cutting edges are further defined in SAE J737, J739, J1304, and J1581. The end bits are further defined in SAE J63.
Standard

Metric Countersunk Holes for Cutting Edges and End Bits

1989-12-01
HISTORICAL
J1580_198912
This document is to be used on cutting edges and end bits in conjunction with metric bolts (Reference ISO 7852-1982) typically used on off-road, self-propelled work machines as described in SAE J1116. The cutting edges are further defined in SAE J737, J739, J1304, and J1581. The end bits are futher defined in SAE J63. This document specifies the principle shapes and dimensions for countersunk square holes.
Standard

Loading Ability Test Procedure - Scrapers

2011-10-27
CURRENT
J764_201110
This SAE Information Report applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See SAE J1116 and J1057a.)
Standard

Hole Spacing for Scraper and Dozer Cutting Edges

1989-08-01
HISTORICAL
J737_198908
This standard is intended for cutting edge sections used on: a. Tractor-scrapers as described in SAE J1057 and J728 b. Dozers as described in SAE J729. These cutting edges are further defined in SAE J738 for cross section and SAE J740 and J1580 for hole conformation. (Note: Some inch dimentions in this standard are not equivalent to the corresponding millimeter figures because values which are widely used have been adapted. This standard specifies hole placement along with length and width of the cutting edge.
Standard

Hole Spacing for Scraper and Dozer Cutting Edges

1983-05-01
HISTORICAL
J737_198305
This standard is intended for cutting edge sections used on: a. Tractor-scrapers as described in SAE J1057 and J728 b. Dozers as described in SAE J729. These cutting edges are further defined in SAE J738 for cross section and SAE J740 and J1580 for hole conformation. (Note: Some inch dimentions in this standard are not equivalent to the corresponding millimeter figures because values which are widely used have been adapted. This standard specifies hole placement along with length and width of the cutting edge.
Standard

Hole Spacing for Scraper and Dozer Cutting Edges

2007-08-30
CURRENT
J737_200708
This standard is intended for cutting edge sections used on: a. Tractor-scrapers as described in SAE J1057 and J728 b. Dozers as described in SAE J729. These cutting edges are further defined in SAE J738 for cross section and SAE J740 and J1580 for hole conformation. (Note: Some inch dimentions in this standard are not equivalent to the corresponding millimeter figures because values which are widely used have been adapted. This standard specifies hole placement along with length and width of the cutting edge.
Standard

Hole Spacing for Scraper and Dozer Cutting Edges

2006-02-01
HISTORICAL
J737_200602
This standard is intended for cutting edge sections used on: a. Tractor-scrapers as described in SAE J1057 and J728 b. Dozers as described in SAE J729. These cutting edges are further defined in SAE J738 for cross section and SAE J740 and J1580 for hole conformation. (Note: Some inch dimentions in this standard are not equivalent to the corresponding millimeter figures because values which are widely used have been adapted. This standard specifies hole placement along with length and width of the cutting edge.
Standard

Cutting Edge-Optional Cross-Sections and Dimensions Loader Straight

2006-02-05
HISTORICAL
J1581_200602
The purpose of this SAE Recommended Practice is to specify dimensions for loader straight cutting edge cross sections without holes and with bolt holes for mounting bolt-on teeth and tooth adapters on loader buckets described by SAE J731. This recommended practice is intended to supplement SAE J1303 and SAE J1304 with cross sections for heavier duty applications, by identifying larger blunts, greater bevel angles, larger bolt holes, and greater bolt spacing.
Standard

Cutting Edge-Optional Cross-Sections and Dimensions Loader Straight

1989-09-01
HISTORICAL
J1581_198909
The purpose of this SAE Recommended Practice is to specify dimensions for loader straight cutting edge cross sections without holes and with bolt holes for mounting bolt-on teeth and tooth adapters on loader buckets described by SAE J731. This recommended practice is intended to supplement SAE J1303 and SAE J1304 with cross sections for heavier duty applications, by identifying larger blunts, greater bevel angles, larger bolt holes, and greater bolt spacing.
Standard

Cutting Edge-Double Bevel Cross Sections

1986-06-01
HISTORICAL
J738_198606
This standard specifies dimensions for cutting edge cross section. This standard is for cutting edge sections typically used in earthmoving machinery defined in SAE J1507: a. Tractor - Scrapers as defined in SAE J728. b. Dozers as described in SAE J729 and J173. c. Loaders as described in SAE J731. d. Graders as described in SAE J870. Hole spacing is defined for dozers and scrapers in J737 and graders in J739. Hole conformation is defined in J740.
X