Search Results

Standard

Undervehicle Coupon Corrosion Tests

2016-04-05

CURRENT

J1293_201604

This document is a road test procedure for comparing the corrosion resistance of both coated and uncoated sheet steels in an undervehicle deicing salt environment.

Standard

UNDERVEHICLE COUPON CORROSION TESTS

1990-01-01

HISTORICAL

J1293_199001

This document is a road test procedure for comparing the corrosion resistance of both coated and uncoated sheet steels in an undervehicle deicing salt environment.

Standard

Testing Dynamic Properties of Elastomeric Isolators

1999-05-01

HISTORICAL

J1085_199905

These methods cover testing procedures for defining and specifying the dynamic characteristics of simple elastomers and simple fabricated elastomeric isolators used in vehicle components. Simple, here, is defined as solid (non-hydraulic) components tested at frequencies less than or equal to 25 Hz.

Standard

Testing Dynamic Properties of Elastomeric Isolators

2017-02-09

CURRENT

J1085_201702

These methods cover testing procedures for defining and specifying the dynamic characteristics of simple elastomers and simple fabricated elastomeric isolators used in vehicle components. Simple, here, is defined as solid (non-hydraulic) components tested at frequencies less than or equal to 25 Hz.

Standard

Technical Report on Low Cycle Fatigue Properties Ferrous and Non-Ferrous Materials

2018-08-24

CURRENT

J1099_201808

Information that provides design guidance in avoiding fatigue failures is outlined in this SAE Information Report. Of necessity, this report is brief, but it does provide a basis for approaching complex fatigue problems. Information presented here can be used in preliminary design estimates of fatigue life, the selection of materials and the analysis of service load and/or strain data. The data presented are for the “low cycle” or strain-controlled methods for predicting fatigue behavior. Note that these methods may not be appropriate for materials with internal defects, such as cast irons, which exhibit different tension and compression stress-strain behavior.

Standard

Technical Report on Low Cycle Fatigue Properties Ferrous and Non-Ferrous Materials

2002-08-13

HISTORICAL

J1099_200208

Information that provides design guidance in avoiding fatigue failures is outlined in this SAE Information Report. Of necessity, this report is brief, but it does provide a basis for approaching complex fatigue problems. Information presented here can be used in preliminary design estimates of fatigue life, the selection of materials and the analysis of service load and/or strain data. The data presented are for the “low cycle” or strain-controlled methods for predicting fatigue behavior. Note that these methods may not be appropriate for materials with internal defects, such as cast irons, which exhibit different tension and compression stress-strain behavior.

Standard

Synthetic Resin Plastic Sealers, Nondrying Type

2013-07-09

CURRENT

J250_201307

The material desired under this recommended practice is a synthetic resin plastic sealer of the nondrying, nonbleeding, and noncorrosive type that may be extruded to the specified size and used as a medium for producing a water tight seal between 2 pressed steel sections or between rubber and steel.

Standard

Surface Match Verification Method for Pressure Sensitive Adhesively Attached Components

2021-01-07

CURRENT

J2215_202101

This SAE Recommended Practice applies to evaluation of the conformance match condition existing between two surfaces. Evaluation of this conformance may be especially useful in bonded applications although it may also have relevance to bolted adjacent surface joint conditions. Since good bonding surface conformity is necessary for providing optimal bond performance with pressure sensitive adhesives, the purpose of this document is to provide a method of evaluating the conformance match of the mating surfaces. This document is intended as a guide toward standard practice but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering the use of this document. Tool types, materials, application tools, and component contact area evaluation methods are included as part of this document.

Standard

Strain-Life Overload Fatigue Data File Format

2004-08-31

HISTORICAL

J2649_200408

SAE data file format for exchanging controlled periodic overload data. The object of this SAE Standard is to provide a simple, common methodology for exchanging the data from periodic overload fatigue tests. These tests consist of a single large fatigue cycle followed by a larger number of smaller cycles. The overloads are fully reversed fatigue cycles while the smaller cycles share a common mean and amplitude.

Standard

Strain-Life Fatigue Data File Format

2018-08-24

CURRENT

J2409_201808

SAE format for a SIMPLE Strain-Life Fatigue Data Exchange File Format. The object of this SAE Standard is to provide a simple common way to exchange strain-life fatigue data collected from ASTM E 606 axial fatigue test data.

Standard

Strain-Life Fatigue Data File Format

2004-11-04

HISTORICAL

J2409_200411

SAE format for a SIMPLE Strain-Life Fatigue Data Exchange File Format. The object of this SAE Standard is to provide a simple common way to exchange strain-life fatigue data collected from ASTM E 606 axial fatigue test data.

Standard

Strain-Life Fatigue Data File Format

2018-08-24

CURRENT

J2649_201808

SAE data file format for exchanging controlled periodic overload data. The object of this SAE Standard is to provide a simple, common methodology for exchanging the data from periodic overload fatigue tests. These tests consist of a single large fatigue cycle followed by a larger number of smaller cycles. The overloads are fully reversed fatigue cycles while the smaller cycles share a common mean and amplitude.

Standard

Steering Ball Studs and Socket Assemblies

2012-10-15

CURRENT

J491_201210

This SAE Recommended Practice has been established for the purpose of providing design criteria and suggested dimensional proportions which may be used for ball studs and ball stud socket assemblies as used on steering systems or control mechanisms of passenger vehicles, trucks and off-road equipment. The recommended practice does not cover all applications. It is intended to provide assistance in obtaining functional satisfaction and interchangeability. The inclusion of dimensional data in this report is not intended to imply that all the products described are stock production sizes. Consumers are requested to consult with manufacturers concerning stock production parts.

Standard

Standard Rainflow File Format

2018-08-24

CURRENT

J2623_201808

This SAE Standard provides a definition of a rainflow file format. This type of simple text file would contain all relevant information about the rainflow cycle content of a time history. Included information are Comments, Signal Range, Signal Mean, Number of Cycles, Signal Maximum, Signal Minimum. Rainflow cycle counting has become the most accepted procedure for identifying material fatigue relevant cycles in complex variable amplitude load time histories. The cycle counting methods account for the effects of material plasticity and material memory of prior deformation, and the resulting compressed history information is used by durability analysts to estimate the effects of a given service or test history.

Standard

Standard Rainflow File Format

2002-04-30

HISTORICAL

J2623_200204

This SAE Standard provides a definition of a rainflow file format. This type of simple text file would contain all relevant information about the rainflow cycle content of a time history. Included information are Comments, Signal Range, Signal Mean, Number of Cycles, Signal Maximum, Signal Minimum. Rainflow cycle counting has become the most accepted procedure for identifying material fatigue relevant cycles in complex variable amplitude load time histories. The cycle counting methods account for the effects of material plasticity and material memory of prior deformation, and the resulting compressed history information is used by durability analysts to estimate the effects of a given service or test history.

Standard

Stainless Steel, SAE 30302, Spring Wire and Springs

2016-04-05

CURRENT

J230_201604

This SAE Recommended Practice covers a high-strength corrosion-resisting steel wire, uniform in mechanical properties, intended for the manufacture of springs and wire forms. It also covers processing requirements of springs and forms fabricated from this wire.

Standard

Stainless Steel 17-7 PH Spring Wire and Springs

2016-04-05

CURRENT

J217_201604

This SAE Recommended Practice covers a high-quality corrosion-resisting steel wire, cold drawn, formed, and heat treated to produce uniform mechanical properties. It is magnetic in all conditions. It is intended for the manufacture of springs and wire forms that are to be heat treated after forming to enhance the spring properties. This document also covers processing requirements of the springs and forms fabricated from this wire.

Standard

Spherical Rod Ends

2012-10-15

CURRENT

J1120_201210

This SAE Standard covers the general and dimensional data for industrial quality spherical rod ends commonly used on control linkages in automotive, marine, construction, and industrial equipment applications. The rod ends described are available from several manufacturers within the range of the interchangeable specifications. The sliding contact spherical self-aligning bearing members (ball and socket) are available in a variety of materials in types shown. The load capacities and wear capabilities vary considerably with the design and fabrication. It is suggested that the manufacturers be consulted for recommendations for the type and design appropriate to particular applications.

Standard

Softening Point of Interior Trim Adhesives

2021-01-07

CURRENT

J1700_202101

This SAE Recommended Practice shall be used to determine the temperature at which an adhesive softens to the point at which it no longer can support a given load.

Standard

Shaft Ends

2014-06-05

CURRENT

J501_201406