Search Results

The time of, and location where ignition first occurs in a diesel fuel spray were investigated in a rapid compression machine (RCM) using the two–dimensional techniques of silicone oil particle scattering imaging (SSI), and the planar laser induced fluorescence (LIF) of formaldehyde. Formaldehyde has been hypothesized to be one of the stable intermediate species marking the start of oxidation reactions in a transient spray under compression ignition conditions. In this study, the LIF images of the formaldehyde formed in a diesel fuel spray during ignition process have been successfully obtained for the first time by exciting formaldehyde with the 3rd harmonic of the Nd:YAG laser. SSI images of the vaporizing spray, and the LIF images of formaldehyde were obtained together with the corresponding time record of combustion chamber pressures at initial ambient temperatures ranging from 580 K to 790 K.

The HCCI engine is a next generation engine, with high efficiency and low emissions. However a rate of pressure rise is a major limitation for high load range. Recently, we are able to reduce the rate of pressure rise using thermal stratification. Nevertheless, this was insufficient to produce high power. Without the higher equivalent ratio, one way to improve the power is to increase the intake boost pressure. It is suggested that the rate of pressure rise is reduced by thermal stratification and the power is increased by boost pressure at the same time. The objective of this work is to understand the characteristics of combustion, knock and emissions for using both thermal stratification and the boost pressure. The calculations are performed by CHEMKIN and modified SENKIN. As a result of increasing the boost pressure, a higher IMEP was attained while the rate of pressure rise increased only slightly in the HCCI with thermal stratification.

CNG/diesel dual-fuel engine is using CNG as a main fuel, and injects diesel only a little as an ignition priming. In this study, remodeling an existing diesel engine into dual-fuel engine that can inject diesel with high pressure by CRDI (Common Rail Direct Injection), and injecting CNG at intake port for premixing. The results show that CNG/diesel dual-fuel engine satisfied coordinate torque and power with conventional diesel engine. And CNG alternation rate is over 89% in all operating ranges of CNG/diesel dual-fuel engine. PM emission is lower 94% than diesel engine, but NOx emission is higher than diesel engine. The output of dual fuel mode is 95% by the diesel mode. At this time, amount of CO₂ and PM are decreased while CO, NOx, and THC are increased. In NEDC mode, exhaust gases except NOx are decreased.

Super lean burn technology is conceived as one of methods for improving the thermal efficiency of SI engines[1][2]. For lean burn, reduction of heat loss and the due to decrease in flame temperature can be expected. However, as the premixed gas dilutes, the combustion speed decreases, so the combustion fluctuation between cycles increases. Also, to improve the thermal efficiency, the ignition timing is advanced to advance the combustion phase. However, when the combustion phase is excessively advanced, knocking occurs, which hinders the improvement of thermal efficiency. Knocking is a phenomenon in which unburned gas in a combustion chamber compressed by a piston and combustion gas suffer compression auto-ignition. It is necessary to avoid knocking because the amplitude of the large pressure wave may cause noise and damage to the engine. Also, knocking is not a steady phenomenon but a phenomenon that fluctuates from cycle to cycle.

An on-board measurement system that simultaneously measures road traffic, vehicle running conditions and exhaust emissions was installed in a diesel freight vehicle with two tons payload. Actual NOx mass emissions were compared with that measured in a typical test mode for urban cities on a chassis dynamometer. The frequency of vehicle accelerations in actual urban cities was found to exceed that of a typical test mode for urban cities on a chassis dynamometer, which resulted in increased NOx from actual running conditions compared with the typical test mode for urban cities. The dynamics of NOx emissions at an actual roadside was also analyzed. It was observed that NOx emission based on distance with an actual city route test was about two times higher than that of a free way route and a typical test mode for urban cities. The reason for high NOx with the city route was explained by the higher frequency of lower gears at which higher NOx is emitted.

Reduction of particulate emissions from diesel engine is an important theme from the view point of air pollution. Experiments were carried out using a four-stroke single cylinder direct-injection diesel engine. A new method to measure diesel particulates has been developed. Particulates were sampled with a freezing method just behind an exhaust valve and examined through a scanning electron microscope. Shape and structure of particulates and the size distributions are measured under wide operating conditions obtained with above method. The total mass of particulate emissions was measured using a dilution tunnel sampling system. The heat release processes were analyzed using indicator diagrams and the relation between burning condition and particulate emissions were discussed, after systematic experiments under constant revolution speed of 2000 r/min for several load and injection timing conditions.

A simulation study was conducted to examine the transition from SI combustion to HCCI combustion in a two-stroke free piston engine fuelled with propane. Operation of the free piston engine was simulated based on the combination of three mathematical models including a dynamic model, a linear alternator model and a thermodynamic model. The dynamic model included an analysis of the piston motion, based on Newton's second law. The linear alternator model included an analysis of electromagnetic force, which was considered to be a resistance force for the piston motion. The thermodynamic model was used to analysis thermodynamic processes in the engine cycle, including scavenging, compression, combustion, and expansion processes. Therein, the scavenging process was assumed to be a perfect process. These mathematical models were combined and solved by a program written in Fortran.

The combustion mechanism of the homogeneous charge compression ignition (HCCI) engine has been investigated by numerical calculations. Calculations were carried out using n-butane/air elementary reactions at 0 dimension and adiabatic condition to simplify the understanding of chemical reaction mechanisms in the HCCI engine without complexities of walls, crevices, and mixture inhomogeneities. n-Butane is the fuel with the smallest carbon number in the alkane family that shows two-stage auto-ignition, heat release with low temperature reaction (LTR) and high temperature reaction (HTR), similar to higher hydrocarbons such as gasoline at HCCI combustion. The CHEMKIN II code, SENKIN and kojima's n-butane elementary reaction scheme were used for the calculations. This paper consists of three main topics. First, the heat release mechanisms of the HCCI engine were investigated. The results show that heat release with LTR is HCHO oxidation reactions.

Lean burn is one method for improving thermal efficiency in spark ignition (SI) engines. Suppression of knocking provides higher thermal efficiency, and ethanol blending is considered an effective way to suppress knocking due to its high octane and high latent heat of evaporation. We investigate the effect of ethanol blending on knocking in an SI engine under lean operating conditions. The Livengood-Wu (LW) integral was performed based on ignition delay duration estimated from a zero-dimensional detailed chemical reaction calculation with pressure and temperature histories. Knocking was suppressed and thermal efficiency increased with ethanol-gasoline blending fuel, even at 0.5 equivalence ratio. Decrease in unburned gas temperature by latent heat of evaporation had a comparable influence on knocking suppression, which was supported by LW integral analysis.

This work experimentally investigates how the dwell time between pilot injection and main injection influences combustion characteristics and emissions (NOx, CO, THC and Smoke) in a single-cylinder DI diesel engine. Additionally, results from diesel injection are compared with those shown in dimethyl ether (DME) injection under the identical injection strategy to demonstrate the sensitivity of the combustion characteristics and emissions to changes of the fuel type. Two fuel injection systems are applied for this experiment due to the differences of fuel characteristic with regard to physical and chemical properties. The injection strategy is accomplished by varying the dwell time (10°CA, 16°CA and 22°CA) between injections at five main injection timings (-4°CA aTDC, -2°CA aTDC, TDC, 2°CA aTDC and 4°CA aTDC). It was found that pilot injection offers good potential to lower the heat-release rate with reduced pressure traces regardless of the dwell time between injections and fuel type.

The dynamics model and model-based controller (LQG servo controller) have been constructed to improve performance of diesel engine in transient condition. The input parameters of the model are fuel quantity of main injection, timing of main injection, fuel quantity of pilot injection, timing of pilot injection, external EGR ratio and boost pressure. The parameters that are succeeded between cycles to express transient condition are residual gas temperature and of residual oxygen. In the model, one cycle is discretized into 10 representative points. The precision of the accuracy of the model and the responsiveness of the controller were confirmed.

The concept of oxygen enriched charging (OEC) was exploratively examined as a means of reducing particulate emissions from a direct injection (DI) diesel engine. A single cylinder DI engine was operated with intake gas oxygen concentrations of 21% to 29%, under a constant engine speed of 40 Hz, and several load conditions. It was found that OEC reduces particulate emissions from a DI diesel engine for all operating conditions tested. Insoluble particulate is especially suppressed by OEC at high load conditions. Oxygen enriched charging has little effect on particulate size distribution at high loads when the mass fraction of extractables is low. Fuel consumption, at constant injection timing, is improved a little by OEC. Emissions of NOx increase exponentially with increasing oxygen concentration. Ignition delay is decreased by OEC and this allows injection timing to be retarded to reduce NOx emissions without increasing the specific fuel consumption.

In this study, effects of nozzle hole diameter and EGR ratio on flame temperature (indication of NO formation) and KL value (indication of soot formation) were investigated. Combustion of a single diesel fuel spray in the cylinder of a rapid compression machine (RCM) was analyzed. Three nozzles with different hole diameter were used corresponding to present, near term and long term heavy duty diesel engine specifications. EGR was simulated through 2%vol. CO2 addition to the inlet air and by increase of in-cylinder surrounding gas temperature. Various types of fuels were used in this. The ignition and combustion processes of diesel fuel spray were observed by a high-speed direct photography and by indicated pressure diagrams. Flame temperature and KL factor were analyzed by a two-color method. With larger nozzle hole diameters there are larger high temperature areas. With smaller nozzle hole diameters there is more soot formed. Introduction of 2% vol.

Knock is a factor hindering enhancement of the thermal efficiency of spark ignition engines, and is an unsteady phenomenon that does not necessarily occur each cycle. In addition, the heat release history of the flame also fluctuates from cycle to cycle, and the auto-ignition process of the unburned mixture (end-gas), compressed by the global increase in pressure due to release of chemical energy, is affected by this fluctuation. Regarding auto-ignition of the end-gas, which can be the origin of knock, this study focused on the fluctuation of the flame heat release pattern, and used a zero-dimensional (0D) detailed chemical reaction calculation in an attempt to analyze and examine the consequence on the end-gas compression and auto-ignition process of changes in the i) start of combustion, ii) combustion duration and iii) center of heat release of the flame.

Homogeneous Charge Compression Ignition (HCCI) engine attracts much attention because of its high thermal efficiency and low NOx, PM emissions. On the other hand, Di-Methyl Ether (DME) is expected as one of alternative fuel for the internal combustion engines. In this study, four-stroke HCCI engine running on DME is developed to make it realistic application in production engines. This paper shows construction of the control method using both internal EGR at high temperature and external EGR at low temperature and estimates the performance of developed HCCI engine. Besides combustion characteristics of DME and the effects of EGR are researched with experiment and numerical calculation with elementary reactions. As a result, developed HCCI engine got comparable high thermal efficiency to conventional diesel engine but much lower Indicated Mean Effective Pressure (IMEP) than that. Meanwhile it can be said that DME is suitable fuel for the HCCI engines in combustion characteristics.

In this study, attention was paid to the method of mixing fuel to solve one of problems of the HCCI engine, which is the avoidance of knocking. The objectives of the work reported in this paper were to research the characteristics of HCCI combustion of the Methane/DME/air pre-mixture in the experiment and to check the oxidation reaction in two cases: when DME was used as an ignition accelerator for the Methane/air pre-picture, and when Hydrogen was used as ignition accelerator. Furthermore, from these results reference was made about basic specifications required fuel for an HCCI engine.

Auto-ignition, which is observed in homogeneous and premixed charge compression ignition engines, allows expansion of the lean flammability limit of engine operation and realization of stable ignition and combustion over a range of ultra-lean conditions, where NOx emissions are very low. In this study, the basic combustion mechanism of auto-ignition and combustion was studied with initial mixture temperatures and compression speeds for n-butane and dimethyl ether. A single-mode type heat release process was observed with n-butane in the homogeneous charge compression ignition test engine.

Delaying CA50(Crank Angle of 50% Heat Release) of the HCCI engine to expansion stroke can lead to high indicated thermal efficiency as well as the avoidance of knocking. However, this method could induce the problem of cycle variability. In this study, the cycle-to-cycle variation of a HCCI engine fueled with DME was investigated. Experimental parameters of each cycle, such as in-cylinder temperature, pressure and gas flow rate, were recorded by fast response system, and analyzed consequently. Moreover, the interdependency between the combustion and the performance parameters were evaluated.

The characteristics of auto-ignition of DME/Air mixture in Homogeneous Charge Compression Ignition (HCCI) engine were investigated by numerical calculation with elementary reactions and experiment. Calculations were carried out using Di-Methyl Ether (DME) elementary reactions at 0 dimension and adiabatic condition. DME is paid attention as the alternative fuel of next generation because of its possibility to take the place of conventional fossil fuels. DME has good characteristics of auto-ignition and combustion with low flame temperature, and makes no soot because of its molecular structure. In autoignition process, DME shows two-stage combustion, heat release with low temperature reaction (LTR) and high temperature reaction (HTR). This characteristic is similar to higher hydrocarbons such as gasoline in auto-ignition process. In this study, analysis of HCCI combustion of DME/Air mixture was carried out by using numerical calculation and comparing with experimental results.

Nowadays, highly super charging is required corresponded to downsizing concept for improving thermal efficiency in direct-injected spark ignition (DISI) engine. However, highly super charging increases the possibility of super-knock caused by pre-ignition. Recently, in many studies, the reason of pre-ignition has been investigated but the reason why pre-ignition leads such strong knocking called super-knock has not been investigated. In DISI engine, it is estimated that there is more inhomogeneity of equivalence ratio and temperature of air-fuel mixture than it in port injection SI engine. In this study, factors which decide self-ignition timing was reviewed and the influence of inhomogeneity of air-fuel mixture to super-knock was investigated based on numerical calculation.