Search Results

As technologies for simultaneously maintaining the current high thermal efficiency of diesel engines and reducing particulate matter (PM) and nitrogen oxide (NOX) emissions, many new combustion concepts have been proposed, including premixed charge compression ignition (PCCI) and low-temperature combustion[1]. However, it is well known that since such new combustion techniques precisely control combustion temperatures and local air-fuel ratios by varying the amount of air, the exhaust gas recirculation (EGR) ratio and the fuel injection timing, they have the issues of being less stable than conventional combustion techniques and of performance that is subject to variance in the fuel and driving conditions. This study concerns a system that addresses these issues by detecting the ignition timing with in-cylinder pressure sensors and by controlling the fuel injection timing and the amount of EGR for optimum combustion onboard.

There has been strong public demand for reduced hazardous exhaust gas emissions and improved fuel economy for automobile engines. In recent years, a number of innovative solutions that lead to a reduction in fuel consumption rate have been developed, including in-cylinder direct injection and lean burn combustion technologies, as well as an engine utilizing a large volume of exhaust gas recirculation (EGR). Furthermore, a homogeneous charge compression ignition (HCCI) engine is under development for actual application. However, one of the issues common to these technologies is less stable combustion, which causes difficulty in engine management. Additionally, it is now mandatory to provide an onboard diagnosis (OBD) system. This requires manufacturers to develop a technology that allows onboard monitoring and control of the combustion state. This paper reports on an innovative combustion diagnostic method using an in-cylinder pressure sensor.

Achieving a multi-cylinder engine with excellent noise/vibration character sties and low friction at the main bearings requires an optimal design not only for the crankshaft construction but also for the bearing support system of the cylinder block. To accomplish that, it is necessary to understand crankshaft system behavior and the bearing load distribution for each of the main bearings. Crankshaft system behavior has traditionally been evaluated experimentally because of the difficulty in performing calculations to predict resonance behavior over the entire engine speed range. A coupled crankshaft-block analysis method has been developed to calculate crankshaft system behavior by treating vibration and lubrication in a systematic manner. This method has the feature that the coupled behavior of the crankshaft and the cylinder block is analyzed by means of main bearing lubrication calculations. This paper presents the results obtained with this method.

The bores of the cylinder block are usually machined prior to assembly with the cylinder head. In this case, bore distortion occurs when the cylinder block is assembled with the cylinder head due to the load applied by the head bolts and the surface pressure of the head gasket. This bore distortion influences sealing and operating characteristics of the pistons and piston rings, requiring an increase in bore thickness and addition of ribs to obtain higher cylinder block rigidity, which lead to an increase in weight. In order to improve engine performance, it is necessary to control bore distortion more effectively. With the aim of reducing bore distortion when assembled with the cylinder head, the bores are machined with a dummy cylinder head installed on the block to provide an equivalent head bolt load and gasket surface pressure. By using this bore circulatory machining technology, bore distortion after cylinder head assembly can be reliably suppressed.

In order to further reduce exhaust gas emissions, an investigation was carried out with premixed charge compression ignition (PCCI) combustion mode using conventional diesel fuel. Past research was carried out with early injection into shallow-dish piston bowl, combined with a narrow nozzle angle setting. Early injection significantly reduced NOX emissions, but some of the fuel spray adhered to the piston bowl surface creating a fuel wall-film which was a major cause in increasing soot, HC and CO emissions and fuel consumption [1]. As a possible solution to this issue, PCCI combustion mode operation on a direct injection diesel engine was investigated with fuel injection timing set close to top dead center (TDC). As a result, regardless of the fuel injection timing, increasing EGR reduced NOx emissions. In terms of fuel consumption, soot, HC and CO, however, fuel injection timing close to TDC was superior to earlier injection, due to the reduction in the fuel wall-film formation.

In order to further reduce exhaust gas emissions, an investigation was carried out concerning premixed charge compression ignition (PCCI) combustion, which is achieved by the early injection of conventional diesel fuel to the combustion chamber. The engine used for the experiments was a single cylinder version of a modern passenger car type common rail engine with a displacement of 550(cm3). An injector with a narrower corn angle was used to prevent interaction of the spray and the cylinder liner. Also, the compression ratio was decreased in order to avoid an excessively advanced ignition situation. Additionally, a large degree of cooled exhaust gas recirculation (EGR) was applied. These measures led to a significantly reduction in NOX emissions. However, a fuel wall-film, which was formed on the surface of the piston bowl wall, caused increases in soot, HC and CO emissions.

A new Variable Valve Event and Lift (VVEL) system has been developed as an effective technology for reconciling environmental performance such as lowering the fuel consumption and exhaust emissions with driving performance. This system can continuously vary both the intake valve lift and event angle (valve opening duration) over a wide operating range to flexibly control the valve timing and lift for a substantial improvement in engine performance. In developing the variable valve lift control system, the essential merit is based on the fundmental configuration of multiple-link mechanism. However, it is required to resolve tribological issues for the specific mechnism. This paper describes the structure of the VVEL system and its operating and motion conversion principles. It also explains the mechanism analysis, dynamic stress analysis and lubrication simulation techniques used in developing the VVEL system, the materials adopted and the surface treatment techniques applied.

A new 2L gasoline turbo engine, named KR20DDET was developed with the world’s first mass-producible variable compression turbo (VC-Turbo) technology using a multi-link variable compression ratio (VCR) mechanism. It is well known that increasing the compression ratio improves gasoline engine thermal efficiency. However, there has always been a compromise for engine designers because of the trade-off between increasing the compression ratio and knocking. At Nissan we have been working on VCR technology for more than 20 years and have now successfully applied this technology to a mass production engine. This technology uses a multi-link mechanism to change the top and bottom dead center positions, thereby allowing the compression ratio to be continuously changed. The VC-Turbo engine with this technology can vary the compression ratio from 14:1 for obtaining high thermal efficiency to 8:1 for delivering high torque by taking advantage of the strong synergy with turbocharging.

Continuous Variable Valve Event and Lift (VVEL) system which improves three major engine performances (fuel consumption/ emission/ driving performace) in well-ballanced manner is developed. This paper introduces outline of the VVEL system, and describes the principle of operation/ transformation and the mechanism of improvement in engine performance of this technology.

Nissan Motor Company has developed a compact and simple new variable valve actuation system called VVEL (Variable Valve Event and Lift) that can vary intake valve lift and valve event angle in a wide range, and adopted it on a newly developed 3.7L, V6 engine. This system combined with a variable valve timing (VTC) mechanism (or a cam phaser) has substantially enhanced engine performance attributes, namely, fuel economy, exhaust emissions, and engine output, because the system has the ability to freely control all of intake valve lift, event duration angle and phasing between intake and exhaust valves. This paper describes an outline of the VVEL system, the principle of system operation, and effects on engine performance attributes by this technology.

Reducing friction in the crankshaft main bearings is an effective means of improving the fuel efficiency of reciprocating internal combustion engines. To realize these improvements, it is necessary to understand the lubricating conditions, in particular the oil film pressure distributions between crankshaft and bearings. In this study, we developed a thin-film pressure sensor and applied it to the measurement of engine main bearing oil film pressure in a 4-cylinder, 2.5 L gasoline engine. This thin-film sensor is applied directly to the bearing surface by sputtering, allowing for measurement of oil film pressure without changing the shape and rigidity of the bearing. Moreover, the sensor material and shape were optimized to minimize influence from strain and temperature on the oil film pressure measurement. Measurements were performed at the No. 2 and 5 main bearings.

Research is under way on an engine system [1] that achieves a variable compression ratio using a multiple-link mechanism between the crankshaft and pistons for the dual purpose of improving fuel economy and power output. At present, there is no database that allows direct judgment of the feasibility of the specific sliding parts in this mechanism. In this paper, the feasibility was examined by making a comparison with the sliding characteristics and material properties of conventional engine parts, for which databases exist, and using evaluation parameters based on mixed elasto-hydrodynamic (EHD) lubrication calculations. In addition, the innovations made to the mixed EHD calculation method used in this study to facilitate calculations under various lubrication conditions are also explained, including the treatment of surface roughness, wear progress and stiffness around the bearings.