Search Results

An increasing concern has been growing in the last years toward health effects due to Particulate Matter (PM) emissions. This triggered the widespread diffusion of Diesel Particulate Filters (DPFs), which equip almost every Diesel car and truck on the market, allowing to get large reduction (in the order of 95% and more) in terms of PM mass. However, PM health effects are believed to be more related to particle number rather than to particle mass. This gave rise in Europe to new regulations for passenger cars on total particle number, that will be introduced from EURO6 on. Engine/Exhaust-System assembly is therefore under investigation, to better understand the effectiveness of aftertreatment components toward particle number reduction, especially by varying engine and exhaust-system design/operating conditions, and to compare particle number emissions to particle mass emissions.

The aim of this work is to carry out statistical analyses on simulated results obtained from large eddy simulations (LES) to characterize spark-ignited combustion process in a partially premixed natural gas mixture in a constant volume combustion chamber (CVCC). Inhomogeneity in fuel concentration was introduced through a fuel jet comprising up to 0.6 per cent of the total fuel mass, in the vicinity of the spark ignition gap. The numerical data were validated against experimental measurements, in particular, in terms of jet penetration and spread, flame front propagation and overall pressure trace. Perturbations in key flow parameters, namely inlet velocity, initial velocity field, and turbulent kinetic energy, were also introduced to evaluate their influence on the combustion event. A total of 12 simulations were conducted.

The aim of this work is to assess the accuracy of results obtained from Large Eddy Simulations (LES) of a partially-premixed natural gas spark-ignition combustion process in a Constant Volume Combustion Chamber (CVCC). To this aim, the results are compared with the experimental data gathered at the University of British Columbia. The computed results show good agreement with both flame front visualization and pressure rise curves, allowing for drawing important statements about the peculiarities of the Partially Stratified Combustion ignition concept and its benefits in ultra-lean combustion processes.

The use of hydrogen (H2) as a fuel for urban private and public transport may represent a major solution to reduce pollutant emissions and CO2 production in urban areas. Looking for short-term solutions, the introduction of moderate quantities of H2 (up to 30%) into Natural Gas (NG) SI engines may be a feasible solution to get a faster combustion process, and therefore less HC and CO2 emissions, and a slight NOx increase which may be potentially limited by the adoption of lean-burn engine control strategies. However, concurrent effects of volumetric efficiency reduction and maximum temperature in the combustion chamber require a careful optimization of operating conditions to fully exploit the H2 potential and to determine the most convenient H2/NG mixture ratio. In that context, 3D numerical tools may be useful to analyze the effect of H2 introduction on engine performance.

A Large Eddy Simulation (LES) numerical study of the Partially Stratified Charge (PSC) combustion process is here proposed, carried out with the open Source code OpenFOAM, in a Constant Volume Combustion Chamber (CVCC). The solver has already been validated in previous papers versus experimental data under a limited range of operating conditions. The operating conditions domain for the model validation is extended in this paper, mostly by varying equivalence ratio, to better highlight the influence of turbulence on flame front propagation. Effects of grid sizing are also shown, to better emphasize the trade-off between the level of accuracy of turbulent vortex description, and their impact on the kinematics of flame propagation. Results show the validity of the approach that is evident by comparing numerical and experimental data.

In 2011-2013, regulations will be tightened for non-road vehicles, via the application of Stage III-B standards in Europe. With state-of-the-art technology (high pressure common rail, cooled EGR), non-road diesel engines will require DPFs to control PM, as 90% reduction is requested with respect to STAGE III-A standards. Additional challenges may also foresee the obtainment of STAGE III-B standards with STAGE III-A engine technology, by means of retrofit systems for PM control. In that case, retrofit systems must furthermore guarantee simple control systems, and must be robust especially in terms of limited back pressure increase during normal operation. Moreover, retrofit systems must offer flexibility from the design point of view, in order to be correctly operated with several engines of same class, possibly characterized by totally different PM flow rates, temperature, NOx and O₂ availability.

Lean burn natural gas engines have high potential in terms of efficiency and NOx emissions in comparison with stoichiometric natural gas engines, and much lower particulate emissions than diesel engines. They are a promising solution to meet the increasingly stringent exhaust emission targets for both light and heavy-duty engines. Partially Stratified-Charge (PSC) is a novel concept which was conceived by prof. Evans (University of British Columbia, Vancouver). This technique allows to further limit pollutant emissions and improve efficiency of an otherwise standard spark-ignition engine fuelled by natural gas, operating with lean air-fuel ratio. The potential of the PSC technique lies in the control of load without throttling by further extending the lean flammability limit.

The use of biodiesel has been widely accepted as an effective solution to reduce greenhouse emissions. The high potential of biodiesel in terms of PM emission reduction may represent an additional motivation for its wide use. This potential is related to the oxygenated nature of biodiesel, as well as its lower PAH and S, which leads, in general, to lower PM emissions as well as equal or slightly higher NOx emissions. According to these observations a different behavior of the Aftertreatment System (AS), especially as far as control issues of the Diesel Particulate Filter are concerned is also expected. The competition with the food sector is currently under debate, thus, besides second generation biofuels (e.g. from algae), the transesterification of Waste Cooking Oil (WCO) is another option, however needing further insight.

The use of biodiesels is an effective way to limit greenhouse emissions and partly limit the dependence on fossil primary sources. Biodiesel fuels also show interesting features in terms of PM-NOx emissions trade-off that appears more favorable toward an optimized control of the Diesel Particulate Filter (DPF). In fact, the DPF, which is the assessed aftertreatment technology to reduce PM emissions below the limits, suffers from fuel consumption penalization or excessive exhaust system backpressure, as a function of the frequency of the regeneration process. On the other side, issues such as the impact of the higher ash content of biodiesel on the DPF performance have also to be better understood. In the given scenario, an experimental study on a DEUTZ 4L off-road Diesel engine coupled to a DOC-DPF (Diesel Oxidation Catalyst-Diesel Particulate Filter) system is proposed in this paper.

Soot filtration represents a major problem for the complete exploiting of Diesel engines characteristics in terms of global efficiency and CO2 emissions. Even though the engines development in the last years let the engine performances improve, exhaust gas after treatment is still required to respect the foreseen limits for soot and NOx emissions. A flow-through particle trap has been presented with a great potential in soot removal without major penalties in terms of exhaust back pressure. The device performance is strictly connected to channel geometry. This paper deals with that relation by means of an experimental-numerical approach.

The development of catalytic converter systems for automotive applications is, to a great extent, related to monolith catalyst support materials and design. In this paper improvements of converter channels fluid-dynamics aiming to enhance pollutant conversion in all the engine operating conditions are investigated with respect to the role of channel cross-section shape on mass and heat transfer processes. The performances of different channel sections, characteristic of ceramic and metallic monoliths, have been compared by two strategies (respectively equal cell density and equal hydraulic diameter). The results have been examined in terms of mass conversion efficiency, thermal behavior and single channel backpressure for coated and non coated single channels. 3D numerical simulations have been used as an analysis tool to give a detailed insight of in-channel phenomena. Classical shapes have been analyzed and their relative performances are reported.

Metal based Diesel Particulate Filters (PM-TRAPs) could represent a short time solution to face with particulate (and NOx) emissions with a small influence on CO2 emission. In fact, the operation principle of the PM-TRAP, based on fluid dynamical behavior of exhaust flow in “ad hoc” shaped geometries, allows to separate the particle content of exhaust-gases but needs to be carefully assessed to optimize filter performances. In this paper a mixed numerical and experimental procedure has been developed; it allows to finely tune the design parameters which can be used to achieve pre-defined targets in terms of particulate matter and fuel consumption. By adopting the previously declared procedure, a PM-TRAP “optimal” geometry has been chosen. Its performance has been verified with respect to experimental data. Results are encouraging and suggest further development of the system.

Particulate Matter (PM) filters are becoming a standard component of Diesel engines exhaust aftertreatment devices to comply with the forthcoming engine emission regulations. However, cost reduction and durability are still critical issues in particular for the integration of the PM-filter with other components of the after-treatment system (e.g. pre-turbo-catalyst, close-coupled-catalyst, PM-filter, SCR). To respect functional (available temperature and gas composition) and space restraints, very complex shapes may result from the design causing tortuous flow patterns and influencing the flow distribution into the PM-filter. Uneven soot distributions in the filter may cause a non-homogeneous development of filter regeneration, leading to failures, for example due to the occurrence of large temperature gradients during the oxidation of soot deposits.