Refine Your Search

Date

Date

Topic

Topic

Technical review Parts Alloys Ground support Maintenance and Aftermarket Truck and Bus Powertrain Committee

Search Results

Viewing 1 to 20 of 37
12Next >Last >>
Sort by title
Standard

Torque Ratings for Power Take-off Mounting Pads
2017-09-19
CURRENT
J2662_201709
This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.
Standard

Torque Ratings for Power Take-off Mounting Pads
2003-07-25
HISTORICAL
J2662_200307
This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.
Standard

SAE NODAL MOUNT
1992-02-01
HISTORICAL
J1134_199202
This SAE Recommended Practice establishes a single bolt pattern for the No. 1 clutch housing (see Figure 1) and the No. 2 clutch housing (see Figure 2). These four bolt patterns are designated to give commonality of mounting brackets in existing frame rails. The 420 mm (16.5 in) span, pad face to pad face, allows the ease of installation in existing frame rail widths. This is also the minimum spacing which will accommodate commonly used clutches.
Standard

SAE NODAL MOUNT
1976-01-01
HISTORICAL
J1134_197601
This SAE Standard establishes a single bolt pattern for both No. 1 and No. 2 clutch housings (see Fig. 1). This four-bolt pattern is designated to give commonality of mounting brackets in existing frame rails. The 16.5 in span, pad face to pad face, allows the ease of installation in existing frame rail widths. This is also the minimum spacing which will accommodate a 15 in two-plate clutch. The bolt pattern due to its symmetry allows reversing or inverting of brackets to attain change in vertical or horizontal positioning with fewer brackets.
Standard

SAE NODAL MOUNT
1983-10-01
HISTORICAL
J1134_198310
This SAE Recommended Practice establishes a single bolt pattern for both No. 1 and No. 2 clutch housings (see Fig. 1). This four-bolt pattern is designated to give commonality of mounting brackets in existing frame rails. The 16.5 in span, pad face to pad face, allows the ease of installation in existing frame rail widths. This is also the minimum spacing which will accommodate a 15.5 in two-plate clutch. The bolt pattern due to its symmetry allows reversing or inverting of brackets to attain change in vertical or horizontal positioning with fewer brackets. The phi (ϕ) symbol is for the convenience of the user in locating areas where technical revisions have been made to the previous issue of the report. If the symbol is next to the report title, it indicates a complete revision of the report.
Standard

Recommended Remanufacturing Procedures for Manual Transmission Clutch Assemblies
2017-08-22
CURRENT
J1915_201708
This SAE Recommended Practice is prepared as a guideline to improve and maintain the quality of remanufactured automotive products. Installation of remanufactured or rebuilt products is often an economical way to repair a vehicle even though they may not fully be equivalent to original equipment parts. Before processing any part, a remanufacturer should determine if the original design and present condition of the core are suitable for remanufacturing, so as to provide durable operation of the part as well as acceptable performance when installed in a vehicle. The remanufacturer should also carefully consider the safety aspects of the product and any recommendations of the original manufacturer related to remanufacturing or rebuilding their product.
Standard

Rating of Winches
1999-06-01
HISTORICAL
J706_199906
This SAE Standard applies only to new winches which are primarily designed for intermittent pulls and lifts and whose configuration and condition are the same as when they were shipped by the manufacturer. They are not intended to be used in any manner for the movement of personnel. They may be driven by any power source recommended by the manufacturer and will be capable of being powered in either direction. They will be equipped with an automatic safety brake system to control a load when lowering under power and positively hold a load when power is not being delivered to the winch. A hydraulic flow control valve or similar device may be used in the brake system to control a load when lowering under power. A clutch to release the drum for “free-spooling” may be provided and will be designed not to disengage itself under load. A drag brake may be provided to control “free-spooling,” but will not be relied on to control or hold a load.
Standard

RECOMMENDED REMANUFACTURING PROCEDURES FOR MANUAL TRANSMISSION CLUTCH ASSEMBLIES
1990-02-01
HISTORICAL
J1915_199002
This SAE Recommended Practice is prepared as a guideline to improve and maintain the quality of remanufactured automotive products. Installation of remanufactured or rebuilt products is often an economical way to repair a vehicle even though they may not fully be equivalent to original equipment parts. Before processing any part, a remanufacturer should determine if the original design and present condition of the core are suitable for remanufacturing, so as to provide durable operation of the part as well as acceptable performance when installed in a vehicle. The remanufacturer should also carefully consider the safety aspects of the product and any recommendations of the original manufacturer related to remanufacturing or rebuilding their product.
Standard

RATING OF WINCHES
1984-06-01
HISTORICAL
J706A_197004
This SAE Standard applies only to new winches which are primarily designed for intermittent pulls and lifts and whose configuration and condition are the same as when they were shipped by the manufacturer. They are not intended to be used in any manner for the movement of personnel. They may be driven by any power source recommended by the manufacturer and will be capable of being powered in either direction. They will be equipped with an automatic safety brake system to control a load when lowering under power and positively hold a load when power is not being delivered to the winch. A hydraulic flow control valve or similar device may be used in the brake system to control a load when lowering under power. A clutch to release the drum for “free-spooling” may be provided and will be designed not to disengage itself under load. A drag brake may be provided to control “free-spooling,” but will not be relied on to control or hold a load.
Standard

RATING OF WINCHES
1985-07-01
HISTORICAL
J706_198406
This SAE Standard applies only to new winches which are primarily designed for intermittent pulls and lifts and whose configuration and condition are the same as when they were shipped by the manufacturer. They are not intended to be used in any manner for the movement of personnel. They may be driven by any power source recommended by the manufacturer and will be capable of being powered in either direction. They will be equipped with an automatic safety brake system to control a load when lowering under power and positively hold a load when power is not being delivered to the winch. A hydraulic flow control valve or similar device may be used in the brake system to control a load when lowering under power. A clutch to release the drum for "free-spooling" may be provided and will be designed not to disengage itself under load. A drag brake may be provided to control "free-spooling," but will not be relied on to control or hold a load.
Standard

RATING OF WINCHES
1990-11-01
HISTORICAL
J706_199011
This SAE Standard applies only to new winches which are primarily designed for intermittent pulls and lifts and whose configuration and condition are the same as when they were shipped by the manufacturer. They are not intended to be used in any manner for the movement of personnel. They may be driven by any power source recommended by the manufacturer and will be capable of being powered in either direction. They will be equipped with an automatic safety brake system to control a load when lowering under power and positively hold a load when power is not being delivered to the winch. A hydraulic flow control valve or similar device may be used in the brake system to control a load when lowering under power. A clutch to release the drum for “free-spooling” may be provided and will be designed not to disengage itself ander load. A drag brake may be provided to control “free-spooling,” but will not be relied on to control or hold a load.
Standard

Pilot Bearings for Truck and Bus Applications
2017-08-14
CURRENT
J1731_201708
This SAE Recommended Practice describes STANDARD-DUTY and EXTREME-DUTY Pilot Bearing requirements and sizes for class 6, 7, and 8 on-highway trucks and buses that use diesel engines and manual transmissions. The recommendations may apply to a wide range of other pilot-bearing applications, such as agricultural, industrial, and construction equipment.
Standard

Pilot Bearings for Truck and Bus Applications
2001-06-12
HISTORICAL
J1731_200106
This SAE Recommended Practice describes STANDARD-DUTY and EXTREME-DUTY Pilot Bearing requirements and sizes for class 6, 7, and 8 on-highway trucks and buses that use diesel engines and manual transmissions. The recommendations may apply to a wide range of other pilot-bearing applications, such as agricultural, industrial, and construction equipment.
Standard

Nomenclature and Terminology for Truck and Bus Drive Axles
2001-08-03
HISTORICAL
J923_200108
This SAE Recommended Practice outlines basic nomenclature in common use for truck and bus drive axle designs. Over a period of years there have been many different designs introduced; however, for this report, only the most common have been selected and only their general construction is illustrated to show the nomenclature of the various parts.
Standard

Nomenclature and Terminology for Truck and Bus Drive Axles
2012-07-02
CURRENT
J923_201207
This SAE Recommended Practice outlines basic nomenclature in common use for truck and bus drive axle designs. Over a period of years there have been many different designs introduced; however, for this report, only the most common have been selected and only their general construction is illustrated to show the nomenclature of the various parts.
12Next >Last >>
X