Search Results

This SAE Recommended Practice: a Defines the functional requirements for a vehicle electrical/electronic diagnostic connector. These functional requirements are separated into two principal areas: connector location/access and connector design. b Establishes terminal assignments to conform to either of two categories: Standard or Manufacturer Discretionary. Rationale relative to intent is provided, where applicable, to minimize ambiguity.

This document supersedes SAE J2012 DEC2007, and is technically equivalent to ISO 15031-6:2010 with the exceptions described in Section 1.2. This document is intended to define the standardized Diagnostic Trouble Codes (DTC) that On-Board Diagnostic (OBD) systems in vehicles are required to report when malfunctions are detected. SAE J2012 may also be used for decoding of enhanced diagnostic DTCs and specifies the ranges reserved for vehicle manufacturer specific usage. This document includes: a Diagnostic Trouble Code format. b A description of the standardized set of Diagnostic Trouble Codes and descriptions contained in SAE J2012-DA. The two most significant bytes of a DTC may be decoded according to two different lists; DTC Format Identifier 0x00 and 0x04. c A description of the standardized set of Diagnostic Trouble Codes subtypes known as Failure Types contained in SAE J2012-DA (applies only when three byte DTCs are used).

This document supersedes SAE J2012 DEC2007, and is technically equivalent to ISO 15031-6:2010 with the exceptions described in 1.2. This document is intended to define the standardized Diagnostic Trouble Codes (DTC) that On-Board Diagnostic (OBD) systems in vehicles are required to report when malfunctions are detected. SAE J2012 may also be used for decoding of enhanced diagnostic DTCs and specifies the ranges reserved for vehicle manufacturer specific usage. This document includes: a Diagnostic Trouble Code format. b A description of the standardized set of Diagnostic Trouble Codes and descriptions contained in SAE J2012DA. The two most significant bytes of a DTC may be decoded according to two different lists; DTC Format Identifier 0x00 and 0x04. c A description of the standardized set of Diagnostic Trouble Codes subtypes known as Failure Types contained in SAE J2012-DA (applies only when three byte DTCs are used).

This document supersedes SAE J2012 DEC2007, and is technically equivalent to ISO 15031-6:2010 with the exceptions described in 1.2.This document is intended to define the standardized Diagnostic Trouble Codes (DTC) that On-Board Diagnostic (OBD) systems in vehicles are required to report when malfunctions are detected. SAE J2012 may also be used for decoding of enhanced diagnostic DTCs and specifies the ranges reserved for vehicle manufacturer specific usage.

The J2012 Digital Annex of Diagnostic Trouble Code Definitions Spreadsheet provides DTC information in an excel format for use in your organization's work processes. The column headings include the same information as contained in the J2012 standard. Information in the excel spreadsheet will be updated several times annually and the spreadsheet includes a column heading denoting which DTCs have been updated in the current version.

The J2012 Digital Annex of Diagnostic Trouble Code Definitions Spreadsheet provides DTC information in an excel format for use in your organization's work processes. The column headings include the same information as contained in the J2012 standard. Information in the excel spreadsheet will be updated several times annually, and the spreadsheet includes a column heading denoting which DTC have been updated in the current version.

The J2012 Digital Annex of Diagnostic Trouble Code Definitions Spreadsheet provides DTC information in an excel format for use in your organization's work processes. The column headings include the same information as contained in the J2012 standard. There is also a column heading denoting which DTC have been updated in the current version.

The J2012 Digital Annex of Diagnostic Trouble Code Definitions Spreadsheet provides DTC information in an excel format for use in your organization's work processes. The column headings include the same information as contained in the J2012 standard. Information in the excel spreadsheet will be updated several times annually, and the spreadsheet includes a column heading denoting which DTC have been updated in the current version.

This SAE Recommended Practice establishes a uniform practice for protecting vehicle components from "unauthorized" access through a vehicle data link connector (DLC). The document defines a security system for motor vehicle and tool manufacturers. It will provide flexibility to tailor systems to the security needs of the vehicle manufacturer. The vehicle modules addressed are those that are capable of having solid state memory contents accessed or altered through the data link connector. Improper memory content alteration could potentially damage the electronics or other vehicle modules; risk the vehicle compliance to government legislated requirements; or risk the vehicle manufacturer's security interests. This document does not imply that other security measures are not required nor possible.

This SAE Recommended Practice establishes a uniform practice for protecting vehicle modules from "unauthorized" intrusion through a vehicle diagnostic data communication link. The security system represents a recommendation for motor vehicle manufacturers and provides flexibility for them to tailor their system to their specific needs. The vehicle modules addressed are those that are capable of having solid-state memory contents altered external to the electronic module through a diagnostic data communication link. Improper memory content alteration could potentially damage the electronics or other vehicle modules; risk the vehicle compliance to government legislated requirements; or risk the vehicle manufacturer's security interests. This document is intended to meet the "tampering protection" provisions of California Air Resources Board OBD II regulations and does not imply that other security measures are not required nor possible.

This SAE Recommended Practice defines diagnostic test modes, and request and response messages, necessary to be supported by vehicle manufacturers and test tools to meet the requirements of the California OBD II regulations, which pertain to vehicle emission-related data only. These messages are intended to be used by any service tool capable of performing California OBD II mandated diagnostics. Diagnostic Test Modes included in this document are: For each test mode, this document includes: a Functional descriptions of test mode b Request and response message formats

This SAE Recommended Practice defines diagnostic test modes, and request and response messages, necessary to be supported by vehicle manufacturers and test tools to meet the requirements of the California OBD II and Federal OBD regulations, which pertain to vehicle emission-related data only. These messages are intended to be used by any service tool capable of performing the mandated diagnostics. Diagnostic Test Modes included in this document are: For each test mode, this specification includes: a Functional descriptions of test mode b Request and response message formats For some of the more complex test modes, an example of messages and an explanation of the interpretation of those messages is included.

This SAE Recommended Practice defines diagnostic test modes, and request and response messages, necessary to be supported by vehicle manufacturers and test tools to meet the requirements of the California OBD II and Federal OBD regulations, which pertain to vehicle emission-related data only. These messages are intended to be used by any service tool capable of performing the mandated diagnostics. In addition, capabilities are defined that are intended to meet other Federal and State regulations pertaining to related issues such as Inspection and Maintenance (I/M) and service information availability. This document is not considered a final authority for interpretation of the regulations, so the reader should determine the applicability of the capabilities defined in this document for their specific need.

This SAE Recommended Practice defines diagnostic test modes, and request and response messages, necessary to be supported by vehicle manufacturers and test tools to meet the requirements of the California OBD II and Federal OBD regulations, which pertain to vehicle emission-related data only. These messages are intended to be used by any service tool capable of performing the mandated diagnostics. In addition, capabilities are defined that are intended to meet other Federal and State regulations pertaining to related issues such as Inspection and Maintenance (I/M) and service information availability. This document provides the mechanism to satisfy requirements included in regulations, and not all capabilities included in this document are required by regulations. This document also is not considered a final authority for interpretation of the regulations, so the reader should determine the applicability of the capabilities defined in this document for their specific need.

SAE J1979-2 describes the communication between the vehicle's OBD systems and test equipment required by OBD regulations. On-Board Diagnostic (OBD) regulations require passenger cars and light-, medium-, and heavy-duty trucks to support a minimum set of diagnostic information to external (off-board) “generic” test equipment.

The specifications contained in this SAE Standard pertain to high tension ignition cable used in road vehicle engine ignition systems.

SAE J1979-3 describes the communication between the zero emissions propulsion systems and test equipment required by government regulations. Standardization regulations require passenger cars and light-, medium-, and heavy-duty trucks to support a minimum set of diagnostic information to external (off-board) “generic” test equipment. To achieve this, SAE J1979-3 is based on the Open Systems Interconnection (OSI) Basic Refer to Model in accordance with ISO/IEC 7498-1 and ISO/IEC 10731, which structures communication systems into seven layers.

SAE J1979-3 describes the communication between the zero emissions propulsion systems and test equipment required by government regulations. Standardization regulations require passenger cars and light-, medium-, and heavy-duty trucks to support a minimum set of diagnostic information to external (off-board) “generic” test equipment. To achieve this, SAE J1979-3 is based on the Open Systems Interconnection (OSI) Basic Refer to Model in accordance with ISO/IEC 7498-1 and ISO/IEC 10731, which structures communication systems into seven layers.

This SAE Recommended Practice defines the Expanded Diagnostic Protocol (EDP), the requirements for the SAE J1978 OBD II Scan Tool for supporting the EDP protocol, and associated requirements for diagnosis and service information to be provided by motor vehicle manufacturers. Appendix A includes worked examples of the use of the protocol.