Refine Your Search

Search Results

Viewing 1 to 10 of 10
Technical Paper

Vehicle Inertial Parameters-Measured Values and Approximations

1988-11-01
881767
This paper describes an apparatus, called the Inertial Parameter Measurement Device (IPMD), which recently has been developed by the National Highway Traffic Safety Administration at its Vehicle Research and Test Center. The IPMD measures the center of gravity height and the pitch, roll, and yaw moments of inertia of a vehicle. The first section of this paper describes the features, capabilities, limitations, and design of the IFMD. This is followed by a presentation of the vehicle parameters that have been measured by it, to date. The final section of the paper presents several commonly used, and one proposed, rules of thumb for estimating inertial parameters. Data from measurements made by the IPMD are used to show the validity of these rules. Curves obtained by fitting the measured data are also shown for the moments of inertia as functions of the vehicle weight.
Technical Paper

The Variation of Static Rollover Metrics With Vehicle Loading and Between Similar Vehicles

1992-02-01
920583
This paper examines variability of two static rollover metrics, Static Stability Factor (SSF) and Tilt Table Ratio (TTR), due to vehicle loading and vehicle-to-vehicle variation. Variability due to loading was determined by measuring SSF and TTR for 14 vehicles/configurations at multiple loadings. Up to five loadings were used per vehicle/configuration tested. Vehicle-to-vehicle variability was studied by measuring SSF and TTR for ten unmodified vehicles of each of four make/models. Five baseline vehicles, as similar as was feasible, were tested. The other five test vehicles spanned the range of submodels and options available. In general, both SSF and TTR decreased as occupants were added to a vehicle. The change in SSF and TTR per occupant was fairly consistent, with changes in TTR being more consistent. Placing ballast on the floor of the cargo compartment had a mixed effect on SSF, raising it for some vehicles and lowering it for others.
Technical Paper

The Importance of Tire Lag on Simulated Transient Vehicle Response

1991-02-01
910235
This paper discusses the importance of having an adequate model for the dynamic response characteristics of tire lateral force to steering inputs. Computer simulation and comparison with experimental results are used to show the importance of including appropriate tire dynamics in simulation tire models to produce accurate predictions of vehicle dynamics. Improvements made to the tire dynamics model of an existing vehicle stability and control simulation, the Vehicle Dynamics Analysis, Non-Linear (VDANL) simulation, are presented. Specifically, the improvements include changing the simulation's tire dynamics from first-order system tire side force lag dynamics to second-order system tire slip angle dynamics. A second-order system representation is necessary to model underdamped characteristics of tires at high speeds. Lagging slip angle (an input to the tire model) causes all slip angle dependent tire force and moment outputs to be lagged.
Technical Paper

The Design of a Suspension Parameter Measurement Device

1987-02-01
870576
This paper describes the theory and design of an apparatus, the Suspension Parameter Measurement Device (SPMD), which has been developed to measure the displacements and forces which occur at the road wheels of a vehicle as the body moves, or as lateral and/or longitudinal forces are applied at the tire/road interface. Wheel movements resulting from the bounce, pitch, or roll motions of the vehicle body in the absence of lateral and longitudinal forces at the tire/road interface are the kinematic characteristics of the suspension. Wheel displacements caused by the application of forces in the plane of the road are defined as the compliance characteristics, while those resulting from motions of the steering wheel are the steering characteristics. The purpose of the SPMD is to measure all of these characteristics, thereby providing data for use in the simulation of the performance of cars and light trucks.
Technical Paper

Simulator Study of Heavy Truck Air Disc Brake Effectiveness During Emergency Braking

2008-04-14
2008-01-1498
In crashes between heavy trucks and light vehicles, most of the fatalities are the occupants of the light vehicle. A reduction in heavy truck stopping distance should lead to a reduction in the number of crashes, the severity of crashes, and consequently the numbers of fatalities and injuries. This study made use of the National Advanced Driving Simulator (NADS). NADS is a full immersion driving simulator used to study driver behavior as well as driver-vehicle reactions and responses. The vehicle dynamics model of the existing heavy truck on NADS had been modified with the creation of two additional brake models. The first was a modified S-cam (larger drums and shoes) and the second was an air-actuated disc brake system. A sample of 108 CDL-licensed drivers was split evenly among the simulations using each of the three braking systems. The drivers were presented with four different emergency stopping situations.
Technical Paper

Simulator Motion Base Sizing Using Simulation

1994-03-01
940227
The National Highway Traffic Safety Administration (NHTSA) has proposed building the National Advanced Driving Simulator (NADS). As proposed, the NADS will move the simulator's cab so that realistic motion cues are provided to the simulator's driver. It is necessary to determine the motion base capabilities that the NADS will need to simulate different severities and types of driving maneuvers with adequate simulated motion fidelity. The objectives of this study were (1) to develop tools, based on existing vehicle dynamics simulations, simulator washout algorithms, and human perceptual models, that allow required motion base capabilities to be determined and (2) to use these tools to perform analyses that determine the motion base capabilities needed by the NADS. The NADS motion base configuration examined during this study, which may not correspond to that used when the NADS is actually constructed, includes an X-Y Carriage capable of large excursions.
Technical Paper

Methodology for Validating the National Advanced Driving Simulator's Vehicle Dynamics (NADSdyna)

1997-02-24
970562
This paper presents an overview of work performed by the National Highway Traffic Safety Administration's (NHTSA) Vehicle Research and Test Center (VRTC) to test, validate, and improve the planned National Advanced Driving Simulator's (NADS) vehicle dynamics simulation. This vehicle dynamics simulation, called NADSdyna, was developed by the University of Iowa's Center for Computer-Aided Design (CCAD) NADSdyna is based upon CCAD's general purpose, real-time, multi-body dynamics software, referred to as the Real-Time Recursive Dynamics (RTRD), supplemented by vehicle dynamics specific submodules VRTC has “beta tested” NADSdyna, making certain that the software both works as computer code and that it correctly models vehicle dynamics. This paper gives an overview of VRTC's beta test work with NADSdyna. The paper explains the methodology used by VRTC to validate NADSdyna.
Technical Paper

Measured Vehicle Inertial Parameters -NHTSA's Data Through September 1992

1993-03-01
930897
This paper is primarily a printed listing of the National Highway Traffic Safety Administration's (NHTSA) Light Vehicle Inertial Parameter Data Base. This data base contains measured vehicle inertial parameters from all of the 356 tests performed to date with NHTSA's Inertial Parameter Measurement Device (IPMD) that have resulted in data thought to be of general interest. Additionally, the data base contains tilt table data from all 168 vehicle tests performed to date using NHTSA's Tilt Table. The paper also summarizes the history of modifications to the IPMD and discusses how these modifications have improved the accuracy of IPMD measurements.
Technical Paper

An Investigation, Via Simulation, of Vehicle Characteristics that Contribute to Steering Maneuver Induced Rollover

1992-02-01
920585
The goal of this research was to find vehicle characteristics which may contribute to steering maneuver induced rollover accidents. This work involved studying vehicle handling dynamics using the Vehicle Dynamics Analysis, Non-Linear (VDANL) computer simulation. The simulation was used to predict vehicle responses while performing 28 different steering induced maneuvers for each of 51 vehicles. Various measures of vehicle response (metrics), such as response times, percent overshoots, etc., were computed for each vehicle from simulation predictions. These vehicle directional response metrics were analyzed in an attempt to identify vehicle characteristics that might be good predictor/explanatory variables for vehicle rollover propensity. The metrics were correlated, using the Statistical Analysis System (SAS) software and logistic regression, with single vehicle accident data from the state of Michigan for the years 1986 through 1988.
Technical Paper

A Reliability Theory Approach to Estimate the Potential Effectiveness of a Crash Avoidance System to Support Lane Change Decisions

1997-02-24
970454
This paper presents the methodology and initial results of an effectiveness estimation effort applied to lane change crash avoidance systems. The lane change maneuver was considered to be composed of a decision phase and an execution phase. The decision phase begins when the driver desires to perform a lane change. It continues until the driver turns the handwheel to move the vehicle laterally into the new lane or until the driver decides to postpone the lane change. During the decision phase, the driver gathers information about the road scene ahead and either present or upcoming traffic or obstacles in the destination lane. The execution phase begins when the driver starts the move into the new lane and continues until the vehicle has been laterally stabilized in the destination lane. If the driver aborts the lane change once started, the maneuver execution phase concludes when the vehicle has been laterally stabilized in the original lane.
X