Search Results

The fuel injection process in the port of a firing 4-valve SI engine at part load and 25°C head temperature was observed by a high speed video camera. Fuel was injected when the valve was closed. The reverse blow-down flow when the intake valve opens has been identified as an important factor in the mixture preparation process because it not only alters the thermal environment of the intake port, but also strip-atomizes the liquid film at the vicinity of the intake valve and carries the droplets away from the engine. In a series of “fuel-on” experiments, the fuel injected in the current cycle was observed to influence the fuel delivery to the engine in the subsequent cycles.

This work examines the effects of valve timing and back pressure on the engine out enthalpy flow which is critical to the light off of the catalyst. The engine behavior is observed under fast-idle condition using a turbocharged production direct injection spark ignition engine with variable cam phasing that could shift both the intake and exhaust valve timing by 50 deg. crank angle. The back pressure is adjusted by throttling the exhaust. The engine operates at a constant net indicated mean effective pressure of 2 bar. The valve timing effect is largely governed by the residual gas trapped. With increasing valve overlap, the exhaust enthalpy flow increases because of the increase in exhaust temperature due to a slower combustion, and of the increase in air and fuel flow to compensate for the lower efficiency due to the slower combustion. When the back pressure is increased, the engine through flow has to increase to compensate for the larger pumping loss.

A cold-start partial oxidation (POX) system was integrated with a modern flexible fuel engine to assess its impact on cold-start performance and emissions. The POX reactor, a small combustion device operating fuel rich, converts liquid fuel into gaseous fuel species (reformate). The reformate from the reactor, when mixed with combustion air, replaces or supplements the standard fuel consumed during an engine start. This prototype integrated cold-start system has successfully reduced emissions from a cold-start on fuel grade ethanol (E95) at 5°C. The integrated POX system reduced the time-averaged hydrocarbon (HC) and carbon monoxide (CO) emissions by 80 and 40 percent, respectively. Starts on E95 reformate were achieved in less than 10 seconds at temperatures as low as -20°C.

The knock metric for controlled auto-ignition (CAI) engines is assessed by considering the physical processes that establish the pressure wave that contributes to the acoustic radiation of the engine, and by analyzing pressure data from a CAI engine. Data sets from the engine operating with port fuel injection, early direct injection and late direct injection are used to monitor the effect of mixture composition stratification. Thermodynamic analysis shows that the local pressure rise produced by heat release has to be discounted by the work spent in acoustic expansion against the ambient pressure to properly predict the pressure wave amplitude. Based on this analysis, a modified correlation between the pressure wave amplitude and the maximum pressure rise rate (MPRR) is developed by introducing an MPRR offset to account for the expansion work.

A sampling system was developed to measure the evolution of the speciated hydrocarbon emissions from a single-cylinder SI engine in a simulated starting and warm-up procedure. A sequence of exhaust samples was drawn and stored for gas chromatograph analysis. The individual sampling aperture was set at 0.13 s which corresponds to ∼ 1 cycle at 900 rpm. The positions of the apertures (in time) were controlled by a computer and were spaced appropriately to capture the warm-up process. The time resolution was of the order of 1 to 2 cycles (at 900 rpm). Results for four different fuels are reported: n-pentane/iso-octane mixture at volume ratio of 20/80 to study the effect of a light fuel component in the mixture; n-decane/iso-octane mixture at 10/90 to study the effect of a heavy fuel component in the mixture; m-xylene and iso-octane at 25/75 to study the effect of an aromatics in the mixture; and a calibration gasoline.

Throttle ramp rate effects on the in-cylinder fuel/air (F/A) excursion was studied in a production engine. The fuel delivered to the cylinder per cycle was measured in-cylinder by a Fast Response Flame Ionization detector. Intake pressure was ramped from 0.4 to 0.9 bar. Under slow ramp rates (∼1 s ramp time), the Engine Electronic Control (EEC) unit provided the correct compensation for delivering a stoichiometric mixture to the cylinder throughout the transient. At fast ramp rates (a fraction of a second ramps), a lean spike followed by a rich one were observed. Based on the actual fuel injected in each cycle during the transient, a x-τ model using a single set of x and τ values reproduced the cycle-to-cycle in-cylinder F/A response for all the throttle ramp rates.

The heat release characteristics in terms of the maximum pressure rise rate (MPRR) and combustion phasing in a partially premixed compression ignition (PPCI) engine are studied using a calibration gasoline. Early port fuel injection provides a nearly homogeneous charge, into which a secondary fuel pulse is added via direct injection (DI) to provide stratification which is affected by the timing of the start of injection (SOI). As the SOI the DI fuel is retarded from early compression, MPRR first decreases, then increases substantially, and decreases again. The MPRR correlates mostly with the combustion phasing. The SOI timing plays an indirect role. The observation is explained by a bulk heat release process of which the rate increases with temperature rather than by a sequential ignition process. Observations from compression ignition of representative homogeneous charges in a Rapid Compression Machine support this explanation.

The initial flame kernel behavior in a SI engine was measured by a spark-plug-fiber-optics probe. From these measurements, the flame kernel may be characterized by an expansion speed and a convection velocity. These quantities were correlated with the bum rate on a cycle-to-cycle basis in an engine configurated with quiescent, swirl, and tumble in-cylinder motion. The expansion speed correlates well with the 0-2 percent mass burn duration for all the configurations. The flame convection velocity depends on the in-cylinder motion in the expected manner. There was, however, only a weak correlation between the 10-90 percent burn duration and the initial flame kernel behavior.

To understand the effects of crevices on the engine-out hydrocarbon emissions, a series of engine experiments was carried out with different piston crevice volumes and with simulated head gasket crevices. The engine-out HC level was found to be modestly sensitive to the piston crevice size in both the warmed-up and the cold engines, but more sensitive to the crevice volume in the head gasket region. A substantial decrease in HC in the cold-to-warm-up engine transition was observed and is attributed mostly to the change in port oxidation.

The effects of charge motion and laminar flame speeds on combustion and exhaust temperature have been studied by using an air jet in the intake flow to produce an adjustable swirl or tumble motion, and by replacing the nitrogen in the intake air by argon or CO₂, thereby increasing or decreasing the laminar flame speed. The objective is to examine the "Late Robust Combustion" concept: whether there are opportunities for producing a high exhaust temperature using retarded combustion to facilitate catalyst warm-up, while at the same time, keeping an acceptable cycle-to-cycle torque variation as measured by the coefficient of variation (COV) of the net indicated mean effective pressure (NIMEP). The operating condition of interest is at the fast idle period of a cold start with engine speed at 1400 RPM and NIMEP at 2.6 bar. A fast burn could be produced by appropriate charge motion. The combustion phasing is primarily a function of the spark timing.

The effect of lubricant composition on vehicle exhaust emissions has been investigated. Emissions from two vehicles were measured when lubricated with four different crankcase lubricants. All emissions tests were performed with California Phase II gasoline over the FTP-75 cycle. The lubricants tested were a conventional mineral oil based lubricant, poly-alpha olefin (PAO) based lubricant, hydrocracked based lubricant and a Volvo first fill lubricant. The first three lubricants were designed to have similar high temperature viscosities whilst using the same additive package. This meant that there were some small differences in the low temperature viscosities. This resulted in the two mineral oil based lubricants being 10W-30 grades and the PAO and hydrocracked based lubricants being 5W-30 grades. The two test vehicles used were both Volvo 850 vehicles, however one was a European specification vehicle and the other a Californian TLEV.

The combustion process after auto-ignition is investigated. Depending on the non-uniformity of the end gas, auto-ignition could initiate a flame, produce pressure waves that excite the engine structure (acoustic knock), or result in detonation (normal or developing). For the “acoustic knock” mode, a knock intensity (KI) is defined as the pressure oscillation amplitude. The KI values over different cycles under a fixed operating condition are observed to have a log-normal distribution. When the operating condition is changed (over different values of λ, EGR, and spark timing), the mean (μ) of log (KI/GIMEP) decreases linearly with the correlation-based ignition delay calculated using the knock-point end gas condition of the mean cycle. The standard deviation σ of log(KI/GIMEP) is approximately a constant, at 0.63. The values of μ and σ thus allow a statistical description of knock from the deterministic calculation of the ignition delay using the mean cycle properties

The angular momentum of a tumble vortex occurring inside a 4-valve spark ignition engine was measured by particle tracking velocimetry, PTV. A cylindrical glass liner was designed for a single cylinder motored engine. Light-scattering particles and a laser light sheet, directed through the axis of the cylinder, were used to observe the simultaneous flow field. Three different intake port designs were used in this study. The in-cylinder tumbling motions were measured and the tumble ratios were calculated. The intake configurations were also visualized and measured with PTV in a steady flow rig, at a fixed valve lift. In addition, the results were compared with measurements from a conventional steady flow rig which measures the angular momentum flux with a torque-meter, and with laser doppler measurements, LDV, in a motored engine. All four techniques indicated clearly the qualitative difference between the ability of the intake ports to produce an in-cylinder tumbling motion.

Engine Hydrocarbon (HC) emissions behaviors in the shut down and re-start processes were examined in a production 4-cylinder 2.4 L engine. Depending on when the power to the ECU was cut off relative to the engine events, there could be two or three mis-fired cylinders (i.e. cylinders with fuel injected but no ignition). The total HC pumped out by the engine into the catalyst in the stopping process was ∼ 4 mg (approximately equaled to the amount of one injection at idle condition). Because the size of the catalyst was larger than the total exhaust volume in the stopping process, this HC was not observed at the catalyst exit. The catalyst temperature was also not affected. When the engine was purged after shut down (by cranking the engine with the injectors and ignition disconnected), the total exit HC was 33 mg. In a restart 90 minutes after shut down, the integrated amount of HC emissions due to residual fuel from the stopping process was 16 mg.

A reciprocating test apparatus was constructed in which the friction of a single piston ring against a liner segment was measured. The lubrication oil film thickness was also measured simultaneously at the mid stroke of the ring travel using a laser fluorescence technique. The apparatus development and operation are described. Results are presented from a test matrix consisting of five different lubrication oils of viscosity (at 30°C) ranging from 49 to 357 cP; at three mean piston speeds of 0.45, 0.89 and 1.34 m/s; and at three ring normal loading of 1.4, 2.9 and 5.7 MPa. At mid stroke, the oil film thickness under the ring was ∼0.5 to 4 μm; the frictional coefficient was ∼0.02 to 0.1. The frictional coefficient for all the lubricants tested increased with normal load, and decreased with piston velocity. Both mixed and hydrodynamic lubrication regimes were observed. The friction behaviors were consistent with the Stribeck diagram.

The engine and its exhaust flow behaviors are investigated in a turbo-charged gasoline direct injection engine under simulated cold-fast-idle condition. The metrics of interest are the exhaust sensible and chemical enthalpy flows, and the exhaust temperature, all of which affect catalyst light off time. The exhaust sensible enthalpy flow is mainly a function of combustion phasing; the exhaust chemical enthalpy flow is mainly a function of equivalence ratio. High sensible and chemical enthalpy flow with acceptable engine stability could be obtained with retarded combustion and enrichment. When split injection is employed with one early and one later and smaller fuel pulse, combustion retards with early secondary injection in the compression stroke but advances with late secondary injection. Comparing gasoline to E85, the latter produces a lower exhaust temperature because of charge cooling effect and because of a faster combustion.

This work examines the effect of valve timing during cold crank-start and cold fast-idle (1200 rpm, 2 bar NIMEP) on the emissions of hydrocarbons (HC) and particulate mass and number (PM/PN). Four different cam-phaser configurations are studied in detail: 1. Baseline stock valve timing. 2. Late intake opening/closing. 3. Early exhaust opening/closing. 4. Late intake phasing combined with early exhaust phasing. Delaying the intake valve opening improves the mixture formation process and results in more than 25% reduction of the HC and of the PM/PN emissions during cold crank-start. Early exhaust valve phasing results in a deterioration of the HC and PM/PN emissions performance during cold crank-start. Nevertheless, early exhaust valve phasing slightly improves the HC emissions and substantially reduces the particulate emissions at cold fast-idle.

In a previous study, a wide range of gasolines with RON∼90 were tested in a single cylinder engine operated in HCCI mode using negative valve overlap, and all were found to have very similar behavior near the low-load limit. Here we broaden the range of gasolines to include PRF90 and PRF60. At high engine speed, both PRF60 and PRF90 behave similarly to all the other gasolines tested. However, at 1000 RPM, PRF90 is very different from all the other gasolines: it ignites very late, and the engine cannot be operated at low load. Simulations using a popular fuel chemistry model cannot distinguish PRF60 and PRF90 under these conditions. However, a new fuel chemistry model correctly shows the onset of fuel sensitivity at low engine speed. Sensitivity analyses indicate the low-load limit at low engine speed strongly depend on both the chemistry parameters and on the heat-transfer parameters.

The performance of an extended stroke spark ignition engine has been assessed by cycle simulation. The base engine is a modern turbo-charged 4-stroke passenger car spark-ignition engine with 10:1 compression ratio. A complex crank mechanism is used so that the intake stroke remains the same while the expansion-to-intake stroke ratio (SR) is varied by changing the crank geometry. The study is limited to the thermodynamic aspect of the extended stroke; the changes in friction, combustion characteristic, and other factors are not included. When the combustion is not knock limited, an efficiency gain of more than 10 percent is obtained for SR = 1.5. At low load, however, there is an efficiency lost due to over-expansion. At the same NIMEP, the extended stroke renders the engine more resistant to knock. At SR of 1.8, the engine is free from knock up to 14 bar NIMEP at 2000 rpm. Under knocking condition, the required spark retard to prevent knocking is less with the extended stroke.

When gas sample is continuously drawn from the cylinder of an internal combustion engine, the sample that appears at the end of the sampling system corresponds to the in-cylinder content sometime ago because of the finite transit time which is a function of the cylinder pressure history. This variable delay causes a dispersion of the sample signal and makes the interpretation of the signal difficult An unsteady flow analysis of a typical sampling system was carried out for selected engine loads and speeds. For typical engine operation, a window in which the delay is approximately constant may be found. This window gets smaller with increase in engine speed, with decrease in load, and with the increase in exit pressure of the sampling system.