Search Results

The research of driver behavior characteristics has been a focus of vehicle handling and stability performance. With the driver preview effort, many different driver preview models of direction control have been proposed and the simulations of driver-vehicle-road closed-loop system made. But in the simulation, most of the conventional models have the same precondition that the road was simply described as a pre-given preview course. How to simulate the driver dynamically deciding vehicle preview course based on the real road circumstance is the key to the further research of the driver model. In this paper, a new driver direction control model is established, which is called the Optimal Preview Lateral Acceleration (OPLA) Model and divided into three sub-models: driver’s information identification model, driver’s fuzzy decision model of vehicle preview course and driver’s performance first-order correction model.

A generalized theoretical model of tire cornering properties is presented in steady state condition with lateral deflection of tread and complex deformation of carcass under consideration. The model is suitable for full range of vertical load and slip angle. Six parameters are defined to represent the characteristics of tire stiffness, contact pressure distribution and carcass deformation. The model is validated against test data. Some simplified models, e.g. brush model, HSRI model when longitudinal force is zero, Fiala model etc., can be derived as some specific cases of this model. The analytic model provides a sound foundation for semi-empirical expression and gains insight into study of vehicle system dynamics.

A tire enveloping model is described by a “four-ports network” system. A flexible roller contact (FRC) model is proposed, in which both tire geometric filtering effect and tire flexible filtering effect are taken into account. Furthermore, partial loss of contact and the variation of contact length are also considered effectively in this model. In the modelling of automobile vibration systems, because of the influences of tire enveloping properties, the road input could not be original road profile. So an effective road input is proposed which is filtered by the tire. Under different obstacles, tire loads and inflation pressures, the simulations of the effective road input are carried out based on the FRC model. The simulation results show that FRC model can describe tire enveloping properties more effectively than rigid roller contact (RRC) model.

In this paper, the predictive control strategy is employed to improve the current tracking performance of hub motor in 4WD electric vehicle due to its fast dynamic response. But the performance of the conventional predictive deadbeat current control suffers greatly from the parameter variations and other disturbances. Toward this, this paper presents a new predictive control strategy for hub motor; this control scheme combines an improved predictive control law with a state-observer to estimate the future motor currents and system disturbances based on a decoupled model. It provides a decoupled control of hub motor and offers stability against the variations in motor inductance and robustness against system uncertainties. The feasibility and validity of the proposed predictive current control strategy is verified through the simulation results.

The objective of this study is to develop a non-steady & non-linear tire model for vehicle dynamic simulation and control for extreme lateral slip condition. This model is provided in a semi-analytical form based on the theoretical non-steady state model, presented at 2nd IAVSD Tyre Conference, Feb. 1997[6]. The tire model is based on a quasi-steady state concept, which generates the dynamic forces and moment according to the dynamic effective slip ratio cooperating with the Unified Semi-Empirical Tire Model for Steady State. Satisfying the theoretical boundary conditions at two sides (lowest & highest) in frequency domain, the tire model is capable of describing the transient force & moment characteristics of tires in higher frequency range, Comparing with the “Linear Approximation” model, presented at 4th AVEC Conference, Sept. 1998[4].

In this paper, a sliding mode observer for estimating vehicle slip angle and tire forces is developed. Firstly, the sliding mode observer design approach is presented. A system damping is included in the sliding mode observer to speed the observer convergence and to decrease the observer chattering. Secondly, the sliding mode observer for vehicle states is developed based on a 7 DOF embedded vehicle model with a nonlinear tire model ‘UniTire’. In addition, since the tire lateral stiffness is sensitive to the vertical load, the load transfers are considered in the embedded model with a set of algebraic equations. Finally, a simulation evaluation of the proposed sliding mode observer is conducted on a validated 14 DOF vehicle model. The simulation results show the model outputs closely match the estimations by the proposed sliding mode observer.

Tire lag property is a basic property of tire dynamics, and it has significant influence on the performance of vehicle dynamics. In distance domain, the side force and moments produced by a massless tire are basically displacement or path frequency dependent, rather than time dependent. In the paper, on the basis of the stretched-string model, the first-order filtering of deflection for the front point of the contact print and the first-order filtering of side force have been introduced. Tire system can be regarded as a first-order linear system under small slip angle. The force response of tire has the characteristics of the responses of first-order linear system under small angle. The relaxation length is an important parameter in studying tire lag property. It decreases with increasing slip angle. It plays an important role in the study of tire transient properties.

This paper presents an ideal force distribution control method for the electric vehicle, which is equipped with four independently in-wheel motors, in order to improve the lateral stability of the vehicle. According to the friction circle of tyre force, the ideal distribution control method can be obtained to make the front and rear wheels reach the adhesion limit at the same time in different conditions. Based on this, the force re-distributed control is applied to enhance the security of vehicle when the in-wheel motor is in the failure mode. The simulation result shows that: the force distributed method can not only improves the lateral stability of the vehicle but also enhances the vehicle safety.

Based on the tire cornering properties in steady state condition, a theoretical model of non-steady state tire cornering properties (NSSTCP) with small lateral inputs is presented. The outputs of the model are lateral force and aligning moment, while the inputs are yaw angle and lateral displacement (or turn slip and slip angle). The deformation characteristics of contact patch are analyzed in non-steady state condition. The flexibility of tread and that of carcass are both taken into account. The deformation of carcass is assumed to compose of translating part, bending part and twisting part. The tests of NSSTCP including pure yaw motion and pure lateral motion are realized with step inputs of yaw angle and slip angle respectively and test data is then transformed into frequency domain. The model is validated through comparing the computational results with test frequency response.

A unified tire model with non-isotropy of friction and arbitrary contact pressure distribution is presented as a foundation to study the key features of a reasonable expression of tire shear force and alignment torque under combined slip conditions. The effects of contact pressure distribution on tire mechanical characteristics are analyzed. A unified semi-empirical tire model with convenience in dynamics simulation is recommended. For determining the model parameters, a series of simple expressions that satisfy the boundary conditions are proposed and a new global fitting method for tire data processing is employed. Based on the improved semi empirical model, the USPA software is developed. This software reduces the modeling time from the tire data to a practical tire model and allows various tire characteristics analyses. Some experimental validations are shown.

For high torque permanent magnet wheel motor, this paper describes an experimental research method to optimize and identify the motor parameters based on the results of offline calculation. In order to improve the accuracy of motor parameters identification, the motor model considering the affect of iron loss was established, and the motor parameters were identified using genetic algorithm (GA). Based on this, parameters validation experiment was performed. The results show that: parameters obtained by this method can be used to describe the steady-state and transient-state response of permanent magnet synchronous motors accurately.

In this paper, on the basis of the extant semi-empirical tire models of non-steady state with pure yaw angle input and pure side slip angle input, two empirical tire models of non-steady state side slip properties are established, one is pure yaw angle input, the other is pure side slip angle input, and both of them have been verified by test data. These two models can be used to approximately express tire force within low frequency. They have their own advantages, and make up for the disadvantages of existing tire models. They provide more choice for the simulation of vehicle dynamics.

Non-steady state (NSS) tire cornering properties show obvious differences from steady state (SS) tire cornering properties. A two-DOF automobile model with steer angle as an input is established based on the known NSS tire model considering complex carcass deformation. The tire model can certainly be applied to modelling of a multi-DOF automobile system. The frequency responses of lateral acceleration and yaw rate are then derived. An evaluation index, amplitude-frequency characteristic of relative error (AFCRE), is used to analyze the influences of NSS front wheels (FW) and/or rear wheels (RW) on automotive handling. The influences of NSS FW are much greater than those of NSS RW only on automotive handling. The established automobile model can also be applied to other similar studies of vehicle dynamics.

Vehicle handling and stability performances are greatly determined by non-steady state (NSS) tire cornering properties. Analytical derivation of NSS tire cornering models are presented in this paper based on Pacejka's string-concept assumption, in which carcass is assumed to be a stretched string with lateral deformation and lateral relaxation. The lateral inputs of the models are either displacement-based (lateral displacement and yaw angle) or slip-based (slip angle and turn slip). The transient deformations in spatial domain in both longitudinal and lateral directions are obtained directly from geometric relationship of contact patch. The additional self-aligning moment due to longitudinal deformation of contact patch after effect of tire width is considered is also achieved according to geometric relationship of contact patch in longitudinal direction and two transient geometric conditions of contact point.

With the development of the advanced driver assistance system and autonomous vehicle techniques, a precise description of the driver’s steering behavior with mathematical models has attracted a great attention. However, the driver’s steering maneuver demonstrates the stochastic characteristic due to a series of complex and uncertain factors, such as the weather, road, and driver’s physiological and psychological limits, generating negative effects on the performance of the vehicle or the driver assistance system. Hence, this paper explores the stochastic characteristic of driver’s steering behavior and a novel steering controller considering this stochastic characteristic is proposed based on stochastic model predictive control (SMPC). Firstly, a search algorithm is derived to describe the driver’s road preview behavior.

A long vehicle is more difficult to drive than a short one, but the mechanism of this phenomenon is still ambiguous. This paper will devote main effort to elaborate this phenomenon based on the theory of preview-follower driver model. Drivers always hope that the vehicle center can travel according to a predetermined trajectory. However, there is often a deviation between the vehicle center predicted by the driver and the actual center. As for this phenomenon, a conception of driver preview eccentricity is proposed. In order to analyze the influence of the proposed conception on vehicle driving track, a multi-axle steering vehicle model is built and some basic expressions of important parameters are deduced from this model firstly. Then, the developmental driver model with the factor of preview eccentricity based on preview-follower theory is established in the state of low velocity quasi-static. Subsequently, this model for long vehicles is extended to a dynamic driver model.

This paper focuses on the modeling process of incorporating inflation pressure into the UniTire model for pure cornering. Via observing and manipulating the tire experimental data, the effects of inflation pressure on the tire cornering property are analyzed in detail, including the impacts on cornering stiffness, the peak friction coefficient, the curvature of transition region and the pneumatic trail. And the brief mechanism explanations are also given for some of these impacts. The results show that some effects of inflation pressure are similar to that of vertical load on the non-dimensional tire cornering property, and there are strong interactive effects between the two operating conditions. Therefore, in order to obtain concise expressions, the inflation pressure is incorporated into the UniTire tire model by analogy with the expressions for vertical load, and the interactive effects are also taken into account.

In the paper, the Flat Plank Tire Tester of Changchun Automobile Institute is introduced. This paper, according to practical experiences, generalizes some issues in the tire's non-steady state test. In the non-steady state test, it must be assured that the footprint centerline of tire coincides with that of slid platform, which guarantees no sliding motion between tire and slid platform during the movement. Due to tire taper effect and inhomogeneous tire material, when its side slip angle is zero, side force and aligning torque are not zeros, but have initial values. Here two approaches are discussed to eliminate the side force and aligning torque. Besides, other factors in the test are put forward for discussion. Eliminating the interference can obviously improve the test accuracy. This paper also provides test curves of both pure side slip angle input and pure yaw angle input.

A novel predictable tire model has been proposed for combined braking and cornering forces, which is based on only a few pure baking and pure cornering tests. It avoids elaborate testing of all kinds of combinations of braking and side forces, which are always expensive and time consuming. It is especially important for truck or other large size tires due to the capability constraints of tire testing facilities for combined shear forces tests. In this paper, the predictive model is based on the concept of slip circle and state stiffness method. The slip circle concept has been used in the COMBINATOR model to obtain the magnitude of the resultant force under combined slip conditions; however the direction assumption used in the COMBINATOR is not suitable for anisotropic tire slip stiffness.

This paper presents a torque distribution algorithm to improve the energy efficiency of four-wheel-drive (4WD) electric vehicles with PMSM hub motors. In order to optimize the torque distribution method, at first the motor model considering the affect of iron loss and the loss model of multi-motors drive system of 4WD electric vehicle with PMSM hub motors, which operate at straight-line condition, are established. Besides, realize the online identification of motor parameters based on the MARS, which is important for updating the loss model parameters of the motor drive system. By doing this, the ideal torque distribution ratio can be obtained from the loss model in real-time. The simulation result using different distribution algorithms shows that the optimized torque distribution algorithm based on the loss model can be useful for improving the energy efficiency.