Search Results

Abstract Water quality monitoring is needed for the effective management of water resources. Periodic sampling and regular inspection/analysis allow one to classify water and identify changes or trends in water quality over time. This article presents a novel concept of an Amphibious Hybrid Unmanned Aerial Vehicle (AHUAV) that can operate in air and water for rapid water sampling, real-time water quality analysis, and water body management. A methodology using the developed AHUAV system for water body management has also been proposed for an easier and effective way of monitoring water bodies using advanced drone technologies. Using drones for water body management can be a cost-effective and efficient way of carrying out regular inspections and continual monitoring.

Abstract The increase in worldwide awareness of environmental issues has necessitated the air transport industry to drastically reduce carbon dioxide emissions. To meet this goal, one solution is the electrification of aircraft propulsion systems. In particular, single-aisle aircraft with partial turboelectric propulsion with approximately 150 passenger seats in the 2030s are the focus. To develop a single-aisle aircraft with partial turboelectric propulsion, an air-cooled interior permanent magnet (IPM) motor with an output of 2 MW is desired. In this article, mathematical system equations that describe heat transfer inside the target air-cooled IPM motor are formulated, and their mathematical analytical solutions are obtained.

Abstract The article considers one of the possible mechanisms of loading the solidity of a cylindrical metal composite high-pressure vessel (MC HPV). This mechanism manifests itself as delamination of a thin-walled metal shell (liner) from a more rigid composite shell causing local buckling. A similar effect can be detected in the manufacturing process of MC HPV, when the composite shell is formed by winding with tension a carbon fiber-reinforced plastic tape on the liner. Pressure transfer from the composite shell to the liner is carried out by the method of temperature analogy, that is, by cooling the composite shell, thermally insulated from the liner. To solve the problem of externally confined liner local buckling an approach is proposed, which is based on three points: the introduction of local technological deviations inherent in actual structures, the determination of the general stress-strain state, and a real-time deforming.

Abstract An aeroengine exhaust plume is one of the important sources of infrared (IR) signature in the 3-5 μm and the 2-3 μm bands. Analysis, characterization, and modeling of the exhaust plume IR emission are needed for insight into its role in aircraft survivability against IR-guided missiles. The IR signature estimation of aeroengine exhaust needs estimation of radiative properties of absorbing-emitting exhaust gases, e.g., carbon dioxide (CO2) and water vapor (H2O). The radiative properties of the gases can be estimated by a mathematical model with a spectroscopic database of these gases. Low-Resolution Transmission (LOWTRAN), Moderate-Resolution Transmission (MODTRAN), High-Resolution Transmission (HITRAN), and High-Temperature Transmission (HITEMP) are some commonly used spectroscopic databases. This study compares Statistical Narrowband (SNB) models with the various other mathematical models used for the estimation of radiative properties of exhaust gases.

Abstract Federal Aviation Administration (FAA)’s 20 years of research and development with 200 unleaded blends and full-scale engine tests on 45 high-octane unleaded blends has not found a “drop-in” unleaded replacement for aviation gasoline (AVGAS) 100 low lead (100LL) fuel. In this study, analysis of compatibility via optimization of Lycoming O-320 engine fuelled with RON 97, RON 98, RON 100, and AVGAS was conducted using the Response Surface Methodology (RSM). Test fuels were compositionally characterized based on Gas Chromatography (GC) analysis and were categorized based on types of Hydrocarbon (HC). Basic fuel properties of fuels in this research were analyzed and recorded. For optimization analysis, engine speed and fuel were considered as the input parameters.

Abstract There has been an increased interest as regards the use of biofuels in aviation gas turbine engines due to global efforts to reduce greenhouse gas emissions along with fluctuating jet fuel prices. This work researches the use of soap-derived biokerosene (SBK) in aircraft engines. SBK is a promising biofuel option for emerging tropical countries as its production requires a relatively simple technology, and its feedstock sources are abundant in these countries. Blends of Jet A-1 with up to 20 vol.% SBK were tested on a 1S/60 Rover gas turbine engine over a range of brake powers to measure engine performance and emissions. The results were then compared to those of pure Jet A-1. It shows that the engine running on SBK/Jet A-1 blends and pure Jet A-1 have almost similar engine performance parameters including engine efficiency, specific fuel consumption (SFC), turbine inlet temperature (TIT), and exhaust gas temperature (EGT).

Abstract Passengers would always like to reach their destinations with minimum commute time. Generating a higher thrust is a necessity. This implies that the turbomachinery associated with the power plant has to rotate faster and with higher efficiencies. However, high rotational speeds, mainly in the transonic regime, often lead to boundary layer separation, shocks, compressor stall, and surge. The current investigation is an attempt to reduce the abovementioned phenomena. It involves the performance study of a smoothened controlled diffusion airfoil (CDA) blade that has been optimized by “Multi-Objective Genetic Algorithm” (MOGA) by altering maximum camber location and stagger angle. Inlet pressure is varied from 15 kPa to 30 kPa and the angle of attack ranging from 40.4° to 56.4°. C48-S16-BS1 is validated and considered as the baseline profile, and all other blades are collated to this.

Abstract Global warming has motivated the aeronautical industry to develop new technologies that will reduce polluting emissions. A direct way to achieve this goal is to reduce fuel consumption. Reference trajectory optimization contributes to this goal by guiding aircraft to zones where meteorological conditions are favorable to execute their required missions and thereby to reduce flight costs. In this article, the reference trajectory was optimized in terms of geographical position, altitude, and speed, by taking into account a Required Time of Arrival (RTA) constraint and weather conditions. The algorithm assumes that there is no traffic and that the aircraft can fly anywhere in the search space. The search space was modeled in the form of a unidirectional weighted graph, fuel burn was computed using a numerical model, and the weather forecast was taken into account.

Abstract This study underscores the benefits of refining the intralogistics process for small- to medium-sized manufacturing businesses (SMEs) in the engineer-to-order (ETO) sector, which relies heavily on manual tasks. Based on industrial visits and primary data from six SMEs, a new intralogistics concept and process was formulated. This approach enhances the value-added time of manufacturing workers while also facilitating complete digital integration as well as improving transparency and traceability. A practical application of this method in a company lead to cutting its lead time by roughly 11.3%. Additionally, improved oversight pinpointed excess inventory, resulting in advantages such as reduced capital needs and storage requirements. Anticipated future enhancements include better efficiency from more experienced warehouse staff and streamlined picking methods. Further, digital advancements hold promise for cost reductions in administrative and supportive roles.

Abstract The drone logistics distribution method, with its small size, quick delivery, and zero-touch, has progressively entered the mainstream of development due to the global epidemic and the rapidly developing global emerging logistics business. In our investigation, a drone and a delivery man worked together to complete the delivery order to a customer’s home as quickly as possible. We realize the combined delivery network between drones and delivery men and focus on the connection and scheduling between drones and delivery men using existing facilities such as ground airports, unmanned stations, delivery men, and drones. Based on the dynamic-vehicle routing problem model, the establishment of a delivery man and drone with a hybrid model, in order to solve the tarmac unmanned aerial vehicle for take-out delivery scheduling difficulties, linking to the delivery man and an adaptive large neighborhood search algorithm solves the model.

Abstract Numerical prediction of a confined, co-flowing, laminar jet diffusion flame has been investigated under sinusoidal “g-jitter” to describe the flame structure; this type of flame-body force interaction is typical of a microgravity environment such as in the spacecraft. We introduced g-jitter in the direction orthogonal to the fuel and air inflow. We show that the lower frequencies (0.1-0.5 Hz) of sinusoidal g-jitter significantly affected the flame geometry and behavior. The majority of the flame structure was found to oscillate directly in response to the imposed g-jitter. It has also been observed that nonlinearity in the response behaviors is more prominent in the reaction zone of the flame.

Abstract This article presents a numerical solution to the problem of delamination in a separable Metal Composite High-Pressure Vessel (MC HPV). This problem is associated with local buckling of the inner metal shell (liner) surrounded by an outer rigid composite shell. A geometrically and physically nonlinear MC HPV deformation model is constructed considering the three-dimensional stress-strain state, real-time mode, and technological deviations inherent in real vessel designs. The model combines the deformation of the vessel end domes and the cylindrical part. A unilateral constraint is believed to exist on the interface between the liner and the composite shell, allowing the liner to delaminate from the latter when bending. Calculations are performed using the finite element method in the LS-DYNA software package in a dynamic formulation. The vessel is divided into solid finite elements such as TSHELL and SOLID.

Abstract This paper proposes a nonlinear observer for the estimation of gravity vector and angles with respect to velocity vector (flight path angle, bank angle) of a high-performance aircraft. The technique is computationally simpler than the extended Kalman filter (EKF) and hence is suitable for onboard implementations when the digital flight control computer (DFCC) has computational burdens. Flight test data of a highly maneuvering flight such as wind-up turns and full rolls have been used to validate the technique.

Abstract It is reasonable to use a two-phase heat transfer loop (TPL) in a thermal control system (TCS) of spacecraft with large heat dissipation. One of the key elements of TPL is a heat-controlled accumulator (HCA). The HCA represents a volume which is filled with vapor and liquid of a single working fluid without bellows. The pressure in a HCA is controlled by the heater. The heat and mass transfer processes in the HCA can proceed with a significant nonequilibrium. This has implications on the regulation of TPL. This article presents a mathematical model of nonequilibrium heat and mass transfer processes in an HCA for microgravity conditions. The model uses the equations of mass and energy conservation separately for the vapor and liquid phases. Interfacial heat and mass transfer is also taken into account. It proposes to use the convective component k for the level of nonequilibrium evaluation.

Abstract Water droplet size variation has been established in the literature as an important variable that influences the behavior and characteristics of water in fuel emulsion. However, with the growing demand for sustainable aviation fuels (SAF), no data is available that shows how these fuels will affect the size of dispersed water droplets and their frequency distribution. To address this lack of knowledge, this study explores and presents experimental results on the characterization of dispersed water droplets in alternative fuels and Jet A-1 fuel under dynamic conditions. The alternative fuels comprised of two fully synthetic fuels, two fuels synthesized from bio-derived materials, and one bio-derived fuel. The data and statistics presented reveal that water droplet frequency and size distribution are sensitive to changes in fuel composition.

Abstract The use of converging-diverging (C-D) variable area nozzle (VAN) in military aeroengines is now common, as it can give optimal expansion and control over engine back pressure, for a wide range of engine operations. At higher main combustion temperatures (desired for supercruise), an increase in the nozzle expansion ratio is needed for optimum performance. But changes in the nozzle throat and exit areas affect the visibility of engine hot parts as the diverging section of the nozzle is visible for a full range of view angle from the rear aspect. The solid angle subtended by engine hot parts varies with change in visibility, which affects the aircraft infrared (IR) signature from the rear aspect. This study compares the performances of fixed and variable area nozzles (FAN and VAN) in terms of engine thrust and IR signature of the engine exhaust system in the boresight for the same increase in combustion temperature.

Abstract While the design of nozzles for diatomic gases is very well established and covered by published works, the case of a diatomic gas dissociating to monatomic along a nozzle is a novel subject that needs a proper mathematical description. These novel studies are relevant to the definition of nozzles for gas-core Nuclear Thermal Rockets (NTR) that are receiving increased attention for the potential advantages they may deliver versus current generation rockets. The article thus reviews the design of the nozzles of gas-core NTR that use hydrogen as the propellant. Propellant temperatures are expected to reach 9,000-15,000 K. Above 1500 K, hydrogen begins to dissociate at low pressures, and around 3000 K dissociation also occurs at high pressures. At a given temperature, the lower the gas pressure the more molecules dissociate, and H2 → H + H. The properties of the gas are a function of the mass fractions of diatomic and monatomic hydrogen x H2 and x H = 1 − x H2.

Abstract Phosphate ester-based hydraulic fluids are commonly used in aviation, due to their fire-resistant properties. However, contamination of jet fuel with hydraulic fluid may cause serious engine failure, hot corrosion of metals, and swelling of elastomer and polymer seals. Identifying and quantifying hydraulic fluids in jet fuels using chromatography is challenging since common hydraulic fluids, such as ExxonMobil™ HyJet™ V and Skydrol™ LD-4, are composed of tri-butyl phosphate, the main peak of which overlaps with peaks from jet fuels in chromatograms. In this work, three techniques to separate and differentiate the jet fuel peaks from the tri-butyl phosphate peaks were developed. Two methods are based on a solid phase extraction (SPE) procedure followed by identification and quantification, which is carried out using a gas chromatograph equipped with a mass spectrometer or a flame ionization detector.

Abstract Significant attention has been focused on Mars due to its relative proximity and possibility of sustaining human life. However, its lack of in-situ sources of energy presents a challenge to generate needed energy on the surface. Comparatively, Titan has a nearly endless source of fuel in its atmosphere and lakes, but both are lacking in regards to their oxidizing capacity. The finding of a possible underground liquid ammonia-water lake on Titan suggests that oxygen might actually be within reach. This effort provides the first theoretical study involving a primary energy generation system on Titan using the atmosphere as a fuel and underground water as the source for the oxygen via electrolysis from wind generated electricity.

Abstract Emissions and effects of climate change have prompted study into fuels that reduce global dependence on traditional fuels. This study seeks to investigate engine performance, thermochemical properties, emissions, and perform NVH analysis of Jet-A and S8 using a single-stage turbojet engine at three engine speeds. Experimental Jet-A results were used to validate a CFX simulation of the engine. Engine performance was quantified using thermocouples, pressure sensors, tachometers, flow meters, and load cells fitted to the engine. Emissions results were collected using an MKS Multigas Emissions Analyzer that examined CO, CO₂, H₂O, NOx, and THC. NVH analysis was conducted using a multifield, free-field microphone, and triaxial accelerometer. This study found that Jet-A operates at higher temperatures and pressures than S8, and S8 requires higher fuel flow rates than Jet-A, leading to poorer efficiency and thrust. S8 produced stronger vibrations over 5 kHz compared to Jet-A.