Search Results

Abstract The water droplet erosion (WDE) on high-speed rotating wheels appears in several engineering fields such as wind turbines, stationary steam turbines, fuel cell turbines, and turbochargers. The main reasons for this phenomenon are the high relative velocity difference between the colliding particles and the rotor, as well as the presence of inadequate material structure and surface parameters. One of the latest challenges in this area is the compressor wheels used in turbochargers, which has a speed up to 300,000 rpm and have typically been made of aluminum alloy for decades, to achieve the lowest possible rotor inertia. However, while in the past this component was only encountered with filtered air, nowadays, due to developments in compliance with tightening emission standards, various fluids also collide with the spinning blades, which can cause mechanical damage.

Abstract Fluid mechanical design of the cylinder charge motion is an important part of an engine development. In the present contribution an intake port geometry is proposed that can be used as a test case for intake port flow simulations. The objective is to fill the gap between generic test cases, such as the backward facing step or the sudden expansion, and simulations of proprietary intake ports, which are barely accessible in the community. For the intake geometry measurement data was generated on a flow-through test bench and a wall-modeled LES-simulation using a hybrid RANS/LES approach for near-wall regions was conducted. The objective is to generate and analyze a reference flow case. Since mesh convergence studies are too costly for scale resolving approaches only one simulation was done, but on a very fine and mostly block-structured numerical mesh to achieve minimal numerical dissipation.

Abstract This article investigates the dynamics of non-smooth and nonlinear oscillations of a bicycle-car model, considering the tire-road separation. Road contact applies a non-holonomic constrain on the dynamics system that makes the equations of motion to be different under in-contact and off-contact conditions. The set of nonlinear equations of the system has been formulated based on nondimensionalization to minimize the number of parameters and generalize the results. To compare the quality of different suspensions in reducing the unpleasant no-contact conditions, we define a contact-free fraction indicator to measure the separation fraction time during a cycle of steady-state oscillation. An observation of frequency responses including vertical displacements, the pitch mode, and the domain of contact-free fraction of time has been investigated to clarify engineering design directions.

Abstract When the vehicle is under braking condition in the longitudinal motion, the vehicle body will tilt due to the inertial force in motion. A high amplitude will result in uncomfortable feelings of the occupant, such as nervousness or dizziness. To solve the problem, this article presents an adaptive damping system (ADS), which combines the vehicle anti-pitch compensation control with the mixed skyhook (SH) and acceleration-driven-damper (ADD) control algorithm. This ADS can not only improve the vibration effect of the vertical motion for the vehicle but also consider the longitudinal motion of the vehicle body. In addition, a new damper mechanical hardware-in-the-loop test bench is built to verify the effectiveness of the algorithm.

Abstract A critical component of vehicle dynamic control systems is the accurate and real-time knowledge of the vehicle’s key states and parameters when running on the road. Such knowledge is also essential for vehicle closed-loop feedback control. Vehicle state and parameter estimation has gradually become an important way to soft-sense some variables that are difficult to measure directly using general sensors. In this work, a seven degrees-of-freedom (7-DOF) nonlinear vehicle dynamics model is established, where consideration of the Magic formula tire model allows us to estimate several vehicle key states using a hybrid algorithm containing an unscented Kalman filter (UKF) and a genetic algorithm (GA). An estimator based on the hybrid algorithm is compared with an estimator based on just a UKF. The results show that the proposed estimator has higher accuracy and fewer computation requirements than the UKF estimator.

Abstract In this article, a hierarchical coordinated control algorithm for integrating active rear steering and driving/braking force distribution (ARS+D/BFD) was presented. The upper-level control was synthesized to generate the required rear steering angle and external yaw moment by using a sliding-mode controller. In the lower-level controller, a control allocation algorithm considering driving/braking actuators and tire forces constraints was designed to assign the desired yaw moment to the four wheels. To this end, an optimization problem including several equality and inequality constraints were defined and solved analytically. Finally, computer simulation results suggest that the proposed hierarchical control scheme was able to help to achieve substantial enhancements in handling performance and stability.

Abstract Advanced passenger vehicles are complex dynamic systems that are equipped with several actuators, possibly including differential braking, active steering, and semi-active or active suspensions. The simultaneous use of several actuators for integrated vehicle motion control has been a topic of great interest in literature. To facilitate this, a technique known as control allocation (CA) has been employed. CA is a technique that enables the coordination of various actuators of a system. One of the main challenges in the study of CA has been the representation of actuator dynamics in the optimal CA problem (OCAP). Using model predictive control allocation (MPCA), this problem has been addressed. Furthermore, the actual dynamics of actuators may vary over the lifespan of the system due to factors such as wear, lack of maintenance, etc. Therefore, it is further required to compensate for any mismatches between the actual actuator parameters and those used in the OCAP.

Abstract Homogeneous Charge Compression Ignition (HCCI) is a promising advanced combustion concept with high efficiencies and low emissions. Chemical kinetic mechanisms and ignition delay correlations (IDCs) are often applied to simulate HCCI combustion. However, a large number of mechanisms and correlations are not developed specifically for HCCI conditions, i.e., lean mixtures and usually with significant residual gas fractions (RGF). To address this issue, a two-part study is conducted. First, experimental ignition delay time (IDT) data from literature under typical HCCI conditions is collected. Then, thirteen widely applied mechanisms for ethanol, natural gas, and primary reference fuel (PRF) blends of isooctane and n-heptane are validated by running constant-volume simulations. Their performance and accuracy are evaluated. Second, the mechanism with the highest accuracy for each fuel is used to generate IDCs for HCCI conditions.

Abstract A numerical study using large-eddy simulations (LES) to reproduce and understand sources of cycle-to-cycle variation (CCV) in spark-initiated internal combustion engines (ICEs) is presented. Two relevantly different spark-ignition (SI) units, that is, a homogeneous-charge slow-speed single-cylinder research unit (the transparent combustion chamber (TCC)-III, Engine 1) and a stratified-charge high-revving speed gasoline direct injection (GDI) (Engine 2) one, are analyzed in fired operations. Multiple-cycle simulations are carried out for both engines and LES results well reproduce the experimentally measured combustion CCV. A correlation study is carried out, emphasizing the decisive influence of the early flame period variability (1% of mass fraction burnt (MFB1)) on the entire combustion event in both ICEs. The focus is moved onto the early flame characteristics, and the crucial task to determine the dominant causes of its variability (if any) is undertaken.

Abstract The automotive industry offers many applications for machine learning (ML), in general, and deep neural networks in particular. However, the real-world deployment of neural networks into safety-critical components remains a challenge as models would need to offer robustness under a wide range of operating conditions. In this work, we focus on uncertainty estimation, which can be used to deliver predictors that fail gracefully, by detecting situations where their predictions are unreliable. Following Gräber et al. [1], we use Recurrent Neural Networks (RNNs) to perform sideslip angle estimation. To perform robust uncertainty estimation, we augment the RNNs with generative models. We demonstrate the advantage of the proposed model architecture over Monte Carlo (MC) dropout [2] on the Revs data set [3].

Abstract In urban roads the engine speed and the load vary suddenly and frequently, resulting in increased exhaust emissions. In such operations, the effect of air injection technique to access the transient response of the engine is of great interest. The effectiveness of air injection technique in improving the transient response under speed transient is investigated in detail [1]; however, it is not evaluated for the load transients. Load step demand of the engine is another important event that limits the transient response of the turbocharger. In the present study, response of a heavy-duty turbocharged diesel engine is investigated for different load conditions. Three cases of load transients are considered: constant load, load magnitude variation, and load scheduling. Air injection technique is simulated and after optimization of injection pressure based on orifice diameter, its effect on the transient response is presented.

Abstract The external driving environment of an autonomous driving vehicle is complex and changeable. In this article, the trajectory tracking control with obstacle avoidance based on model predictive control was presented. Specifically, double-level control scheme by controlling the front steering angle was used in our research, and the double level is composed of the high level of model predictive controller for local trajectory planning and low level of model predictive controller for trajectory tracking. At high level, the local trajectory planner based on the point-mass model was designed. Then, at low level, the linear time-varying vehicle dynamics model was presented, and the trajectory tracking controller was proposed considering control variable, control increment, and output constraint. Finally, the trajectory tracking performance was tested in co-simulation environment with CarSim and Simulink, and the tracking errors were analyzed.

Abstract This article proposes a new misfire detection index, the ΔGap slope, for a four-cylinder engine. However, the proposed index is not limited to four-cylinder engines. The ΔGap slope uses the tooth time measured using the existing crankshaft position sensor; therefore, an additional sensor is not required, which makes it economical. The ΔGap slope is defined as the difference between the gap slopes of the same cylinder for two adjacent cycles. Various factors that cause deviations in gap slopes between cylinders can be eliminated in the process of determining the difference between two gap slopes. Hence, in contrast with the existing engine roughness method, the ΔGap slope has the advantage of not requiring compensation for deviations between the cylinders. The conventional gap slope method must use different sets of thresholds for each cylinder located at the same position on the sensor wheel, which results in multiple thresholds being applied.

Abstract This article introduces a finite element (FE) approach to determine tire deformation and its effect on open-wheel race car aerodynamics at high vehicle velocities. In recent literature tire deformation was measured optically. Combined loads like accelerating at a corner exit are difficult to reproduce in wind tunnels and require several optical devices to measure the tire deformation. In contrast, an FE approach is capable of determining the tire deformation in combined load states accurately. Additionally, the temperature influence on tire deformation is investigated. The FE tire model was validated using three-dimensional (3D) scan measurements; stiffness measurements in the vertical, lateral, and longitudinal direction; and the change of loaded radius with speed at different loads, respectively. The deformed shape of the tire of the FE model was used in a computational fluid dynamics (CFD) simulation.

Abstract To investigate the effect of a tire blowout (TBO) on the dynamics of the vehicle comprehensively, a three-dimensional full-vehicle multibody mathematical model is developed and integrated with the nonlinear Dugoff’s tire model. In order to ensure the validity of the developed model, a series of standard maneuvers is carried out and the resulting response is verified using the high-fidelity MSC Adams package. Consequently, the in-plane, as well as out-of-plane dynamics of the vehicle, is extensively examined through a sequence of TBO scenarios with various blown tires and during both rectilinear and curvilinear motion. Moreover, the different possible inputs from the driver, the road bank angle, and the antiroll bar have been accounted for. The results show that the dynamic behavior of the vehicle is tremendously affected both in-plane and out-of-plane and its directional stability is degraded.

Abstract Diesel engines include systems for cooling, lubrication, and fuel injection and contain a variety of components. A malfunction in any of the engine systems or the presence of any faulty element influences engine performance and deteriorates its components. This research is concerned with the untimely appearance of vital cracks in the liners of a turbocharged heavy-duty Diesel engine. To find the root causes for premature failure, rigorous examinations through visual observations, material characterization, and metallographic investigations are performed. These include Scanning Electron Microscope (SEM) and Energy-Dispersive Spectroscopy (EDS), fracture mechanics analysis, and performance examination, which are also followed by Finite Element Moldings. To find the proper remedy to resolve the problem, drawing a precise and reliable picture of the engine’s operating conditions is required.

Abstract Increasing thermal and fuel efficiency in Internal Combustion Engines (ICEs) requires thorough investigations on the combustion process and its thermodynamics. The first law of thermodynamics expresses the balance of the energy, while the second law specifies the maximum achievable work. In this article, Low-Temperature Combustion (LTC) strategies, including Homogeneous Charge Compression Ignition (HCCI), Reactivity Controlled Compression Ignition (RCCI), Partially Premixed Combustion (PPC), and Direct Dual-Fuel Stratification (DDFS) were analyzed by the first and second law approaches, and they were compared with ideal-diesel cycle and Conventional Diesel Combustion (CDC). HCCI and RCCI had the highest exergy efficiency of 50.8% and 49.2%, respectively, compared to other cases, and exergy destruction in these cases was the lowest (25.3% and 27.5%, respectively).

Abstract Neutron diffraction is a powerful tool for noninvasive and nondestructive characterization of materials and can be applied even in large devices such as internal combustion engines thanks to neutrons’ exceptional ability to penetrate many materials. While proof-of-concept experiments have shown the ability to measure spatially and temporally resolved lattice strains in a small aluminum engine on a timescale of minutes over a limited spatial region, extending this capability to timescales on the order of a crank angle degree over the full volume of the combustion chamber requires careful design and optimization of the engine structure to minimize attenuation of the incident and diffracted neutrons to maximize count rates.

Abstract To assess the effect of the presence of carbon dioxide (CO2) in natural gases on the knock resistance of fuel, the knock behavior of a lean-burn, high-speed medium Brake Mean Effective Pressure (BMEP) Combined Heat and Power (CHP) engine fueled with CH4 + 8 mole% C3H8 mixtures. The engine experiments are supplemented with ignition measurements and simulations of ignition and cylinder processes for various fuel compositions. The engine results show that increasing the fraction of CO2 results in an increase in knock resistance. The analysis of simulations of cylinder processes shows that for binary mixtures (CH4/CO2) and ternary mixtures (CH4/C3H8/CO2) the increase in knock resistance with increasing CO2 fraction is caused by the reduction in peak pressure/temperature, which consequently increases the autoignition delay time of the mixture.

Abstract Pyrotechnic seat belt pretensioners typically remove 8–15 cm of belt slack and help couple an occupant to the seat. Our study investigated pretensioner deployment on forward-leaning, live volunteers. The forward-leaning position was chosen because research indicates that passengers frequently depart from a standard sitting position. Characteristics of the 3D kinematics of forward-leaning volunteers following pretensioner deployment determines if body size is correlated with subject response. Nine adult subjects (three female), ages 18–43 years old, across a wide range of body sizes (50–120 kg) were tested. The age was limited to young, active adults as pyrotechnic pretensioners can deliver a notable force to the trunk. Subjects assumed a forward-leaning position, with 26 cm between C7 and the headrest, in a laboratory setting that replicated the passenger seat of a vehicle.