Search Results

Abstract The key issues of automatic emergency braking (AEB) control algorithm are when and how to brake. This article proposes an AEB control algorithm that integrates risk perception (RP) and emergency braking characteristics of professional drivers for rear-end collision avoidance. Using the formulated RP by time to collision (TTC) and time headway (THW), the brake trigger time can be determined. Based on the professional driver fitting (PDF) characteristic, the brake pattern can be developed. Through MATLAB/Simulink simulation platform, the European New Car Assessment Programme (Euro-NCAP) test scenarios are used to verify the proposed control algorithm. The simulation results show that compared with the TTC control algorithm, PDF control algorithm, and the integrated PDF and TTC control algorithm, the proposed integrated PDF and RP control algorithm has the best performance, which can not only ensure safety and brake comfort, but also improve the road resource utilization rate.

Abstract Personal watercraft (PWC) users and other high-speed watersports participants have sustained rectal and vaginal injuries during falls into the water, herein referred to as water intrusion injuries (WIIs). WIIs result from the rapid introduction of water into these lower body cavities causing injury to the soft tissues of the perineum, rectum, and vagina. While case studies of injured water-skiers and PWC users are reported in the literature, there is little information related to passenger kinematics and pressure exposure during a rearward fall from a PWC. The results of an experimental study of passenger falls from two “high-performance” PWC are presented herein. A human passenger was caused to fall rearward as the PWC was accelerated at maximum throttle starting from idle speed (≈3–4 mph) and planing speeds of ≈20–30 mph. The subject passenger fell from the aft seat position and while standing on the rear platform.

Abstract The crush energy is a key parameter to determine the delta-V in accident reconstructions. Since an accurate car crush profile can be obtained from 3D scanners, this research aims at validating the methods currently used in calculating crush energy from a crush profile. For this validation, a finite element (FE) car model was analyzed using various types of impact conditions to investigate the theory of energy-based accident reconstruction. Two methods exist to calculate the crush energy: the work based on the barrier force and the work based on force calculated by the vehicle acceleration times the vehicle mass. We show that the crush energy calculated from the barrier force was substantially larger than the internal energy calculated from the FE model. Whereas the crush energy calculated from the vehicle acceleration was comparable to the internal energy of the FE model.

Abstract The first objective of this study, addressed in Part 1, is to use finite element (FE) human body modeling (HBM) to evaluate the tangent of the Belt-to-Pelvis angle (tanθBTP) as a submarining predictor in frontal crashes for occupants in reclined seats. The second objective, addressed in Part 2, is to use this predictor to assess two technical solutions for reducing submarining risks for two different occupant anthropometries. In Part 1, tanθBTP (the lap belt penetration from the anterior superior iliac spine [ASIS] in the abdominal direction) was evaluated in impact simulations with varying seat belt anchor positions. Sled simulations with a 56 km/h full-frontal crash pulse were performed with the SAFER HBM morphed to the anthropometry of a small female and average male. A correlation was found between the submarining predictor and submarining.

Abstract To investigate the effect of a tire blowout (TBO) on the dynamics of the vehicle comprehensively, a three-dimensional full-vehicle multibody mathematical model is developed and integrated with the nonlinear Dugoff’s tire model. In order to ensure the validity of the developed model, a series of standard maneuvers is carried out and the resulting response is verified using the high-fidelity MSC Adams package. Consequently, the in-plane, as well as out-of-plane dynamics of the vehicle, is extensively examined through a sequence of TBO scenarios with various blown tires and during both rectilinear and curvilinear motion. Moreover, the different possible inputs from the driver, the road bank angle, and the antiroll bar have been accounted for. The results show that the dynamic behavior of the vehicle is tremendously affected both in-plane and out-of-plane and its directional stability is degraded.

Abstract The article considers the issues of a systemic approach to studying safety levels in transport operations and ways to increase the safety of the operator-machine system in Russian transport. The principal and problematic issues of reducing the risk of injury by preventing traffic accidents and reducing the severity of their impact have not been sufficiently addressed. When performing transport operations, there are often disagreements between the elements of the “Operator, Machine, and Environment” technological system due to the influence of external conditions and parameters of the constantly-changing environment in the workplace. This leads to a sharp increase in the number of failures of system elements, which reduces the level of safety of transport operations.

Abstract The frequency of video-capturing collision events from surveillance systems are increasing in reconstruction analyses. The video that has been provided to the investigator may not always include a clear perspective of the relevant area of interest. For example, surveillance video of an incident may have captured a pre- or post-incident perspective that, while failing to capture the precise moment when the pedestrian was struck by a vehicle, still contains valuable information that can be used to assist in reconstructing the incident. When surveillance video is received, a quick and efficient technique to place the subject object or objects into a three-dimensional environment with a known rate of error would add value to the investigation.

Abstract Heavy commercial vehicles play an important role in creating the trade and economic balance of countries. Also, the durability and safety of heavy commercial vehicles come to the fore. Heavy commercial vehicles consist of two parts. These are the chassis area with the equipment that allows the vehicle to move and the cabin section where the driver is located. The cabin area is the most important area that ensures the highest level of driver safety. Considering that the production of trucks is increasing day by day, it is inevitable for companies to increase their R&D activities in the field of cabin and cabin suspension systems for much safer, durable, and comfortable trucks. This study aims to determine the safe torque value of the fasteners and their assembly sequence of the Cab Suspension Console, which is one of the most important connection parts in a truck and which can cause a fatal accident by breaking.

Abstract TOC

Abstract TOC

Abstract TOC

Abstract The causes of accidents involving nonconventional bicycle types have hardly been investigated in the literature to date. However, these vehicles could play an important role in reducing the CO2 emissions generated by traffic. As a basis for improving the driving safety of these environmentally friendly vehicles, this article presents the results of a survey on accidents and near-accidents of multitrack bicycle vehicles. More than 120 critical or accident situations of 86 drivers were analyzed. The situations are investigated with respect to the circumstances, the causes, and the consequences of the accidents using manual analysis and multiple correspondence analysis. A distinction is made between single accidents and accidents with another party. The aim of the survey is not to make statistically accurate statements on the frequency and probability of accidents, but rather to analyze the accident or near-accident circumstances.

Eighteen research posters were prepared and presented by student authors at the 18th Annual Injury Biomechanics Symposium. The posters covered a wide breadth of works-in-progress and recently completed projects.

Abstract While historically the rear seat has been considered safer than the front seat, recent studies have suggested that adult occupants have a higher relative risk of injury and death in the rear seat compared to the front seat. Advancements in safety technologies in the front seat have outpaced those in the rear seat, where they vary greatly between vehicle makes and models. Of particular concern is occupant submarining, for which the lap belt slips off of the pelvis and directly loads the abdomen. In this study, frontal crash sled tests with seven vehicle bucks were conducted to assess submarining protection for two rear-seated 50th-percentile male anthropomorphic test devices (ATDs), the Hybrid III-50M and THOR-50M. Tests involved either a ΔV of 56 kph or 32 kph. Submarining incidence and severity for Hybrid III and THOR were assessed using posttest photographs, high-speed videos, and seat belt loads.

Abstract The objective of the study was to evaluate the quasi-static and fatigue performance of automotive anti-roll bars (ARBs) under extreme environmental conditions. Flexural quasi-static and fatigue tests of SAE 1040 steel were conducted above and below the ductile-to-brittle transition temperature (DBTT) in flexure and compared with their room temperature performance. The flexural strength increased by decreasing the temperature to −40°C. The fatigue lives are determined for stress levels of 87%, 60%, and 30% of their flexural strength under displacement mode in constant amplitude loading. Experimental stress versus the number of cycles (S-N) curves of SAE 1040 steel state that all tube specimens have fatigue limits that were more than 100,000 cycles at −40°C. The fatigue life of the SAE 1040 tube exhibited infinite life below the ductile-to-brittle transition (DBT).

Abstract A research program has been launched in Iran to develop an evaluation method for comparing the safety performance of vehicles in real-world collisions with crash test results. The goal of this research program is to flag vehicle models whose safety performance in real-world accidents does not match their crash test results. As part of this research program, a metric is needed to evaluate the severity of side impacts in crash tests and real-world accidents. In this work, several vehicle-based metrics were analyzed and calculated for a dataset of more than 500 side impact tests from the NHTSA crash test database. The correlation between the metric values and the dummy injury criteria was studied to find the most appropriate metric with the strongest correlation coefficient values with the dummy injury criteria.

Abstract Parking an articulated vehicle is a challenging task that requires skill, experience, and visibility from the driver. An automatic parking system for articulated vehicles can make this task easier and more efficient. This article proposes a novel method that finds an optimal path and controls the vehicle with an innovative method while considering its kinematics and environmental constraints and attempts to mathematically explain the behavior of a driver who can perform a complex scenario, called the articulated vehicle park maneuver, without falling into the jackknifing phenomena. In other words, the proposed method models how drivers park articulated vehicles in difficult situations, using different sub-scenarios and mathematical models.

Abstract Compressive impacts on the cervical spine can result in bony fractures. Bone fragments displaced into the spinal canal produce spinal canal occlusion, increasing the potential for spinal cord injury (SCI). Human body models (HBMs) provide an opportunity to investigate SCI but currently need to be improved in their ability to model compression fractures and the resulting material flow. Previous work to improve fracture prediction included the development of an anisotropic material model for the bone (hard tissues) of the vertebrae assessed in a functional spinal unit (FSU) model. In the FSU model, bony failure was modeled with strain-based element erosion, with a limitation that material that could occlude the spinal canal during compression was removed when an element was eroded.

Abstract One of the techniques that accident reconstructionists and experts utilize to define the severity of an accident is based on the airbag deployment thresholds. As such, if during an event, the airbags did not deploy, it is concluded that the threshold could be considered as the upper bound for the forces and the accelerations that the vehicle experienced as a result of the impact. The National Highway Transportation Safety Administration (NHTSA) provides a database based on their investigations on motor vehicle accidents in which some of these investigations involved imaging the airbag control module (ACM) data. NHTSA made these data publicly available. The goal of this study was to analyze the event data recorder (EDR) data from these real-world incidents with a focus on the events in which vehicles’ side airbags were deployed as a result of the impacts and determine the lower-bound side airbag deployment thresholds during real-world cases.

Abstract Purpose: Obesity can be a contributing factor to decrease head injuries in motor vehicle collisions (MVCs). We sought to assess whether obesity is associated with decreased head injury from MVCs by sex. Methods: This study was a retrospective observational study and evaluated crash data from 1997 to 2015 obtained from the International Center for Automotive Medicine. Patients were categorized into normal, overweight, and obesity subgroups. The primary endpoint was serious head injury. Multivariate logistic regression analysis was performed, and adjusted odds ratios (AORs) of subgroups were calculated for study outcomes adjusted for any potential confounders. Results: Among enrolled 588 patients, 262 were male with 30.9% normal, 40.1% overweight, and 29.0% obesity subgroups, and 326 were female with 44.8% normal, 24.8% overweight, and 30.4% obesity subgroups.