Refine Your Search

Topic

Search Results

Viewing 1 to 14 of 14
Journal Article

Wheel Chock Key Design Elements and Geometrical Profile for Truck Vehicle Restraint

2018-06-06
Abstract Wheel chocks are rather simple compliant mechanisms for stabilizing vehicles at rest. However, chocks must be carefully designed given the complex interaction between the chock and the tire/suspension system. Despite their importance for safety, literature is surprisingly limited in terms of what makes a wheel chock efficient. Using simple but reliable quasi-static mechanical models, this study identifies mechanical requirements that help to avoid a number of failure modes associated with many existing wheel chocks. Given that chock grounding is not always possible, a chock’s maximum restraining capacity is only obtained when the wheel is completely supported by the chock. A generic chock profile is proposed to achieve this objective while mitigating undesirable failure modes. The profile is based on fundamental mechanical principles and no assumption is made on the load interaction between the chock and the wheel.
Journal Article

Studies on Friction Mechanism of NAO Brake-Pads Containing Potassium Titanate Powder as a Theme Ingredient

2017-09-17
Abstract Potassium titanate (KT) fibers/whiskers are used as a functional filler for partial replacement of asbestos in NAO friction materials (FMs). Based on little information reported in open literature; its exact role is not well defined since some papers claim it as the booster for resistance to fade (FR), or wear (WR) and sometimes as damper for friction fluctuations. Interestingly, KT fibers and whiskers (but not powder) are proved as carcinogens by the International Agency for Research on Cancer (IARC). However, hardly any efforts are reported on exploration of influence of KT powder and its optimum amount in NAO FMs (realistic composites) in the literature. Hence a series of five realistic multi-ingredient compositions in the form of brake-pads with similar parent composition but varying in the content of KT powder from 0 to 15 wt% (in the steps of 3) were developed. These composites were characterized for physical, mechanical, chemical and tribological performance.
Journal Article

PSO-Fuzzy Gain Scheduling of PID Controllers for a Nonlinear Half-Vehicle Suspension System

2018-11-19
Abstract The present article addresses the gain scheduling of proportional-integral-differential (PID) controllers using fuzzy set theory coupled with a metaheuristic optimization technique to control the vehicle nonlinear suspension system. The nonlinearities of the vehicle suspension system are due to the asymmetric piecewise dampers, quadratic tire stiffness, and the cubical spring stiffness. Conventional PID controller suffers from the low performance subject to modeling nonlinearities, while fuzzy logic controller (FLC), as a universal approximator, has the capacity to deal with the nonlinear, stochastic, and complex models. However, finding the optimal Mamdani FLC rules is still a challenging task in addition to a proper architecture of the membership functions (MFs). As a remedy to this drawback, particle swarm optimization (PSO) technique is employed in this article to improve the efficiency of the FLC-based PID controllers.
Journal Article

Influence of Intelligent Active Suspension System Controller Design Techniques on Vehicle Braking Characteristics

2018-12-04
Abstract This article presents a comprehensive investigation for the interaction between vehicle ride vibration control and braking control using two degrees of freedom (2DOF) quarter vehicle model. A typical limited bandwidth active suspension system with nonlinear spring and damping characteristics of practical hydraulic and pneumatic components is controlled to regulate both suspension and tire forces and therefore provide the optimum ride comfort and braking performance of an anti-lock brake system (ABS). In order to design a suitable controller for this nonlinear integrated system, various control techniques are followed including state feedback tuned using Linear Quadratic Regulator (LQR), state feedback tuned using Genetic Algorithm (GA), Proportional Integrated (PI) tuned genetically, and Fuzzy Logic Control (FLC). The ABS control system is designed to limit skid ratio below threshold of 15%.
Journal Article

Improving Vehicle Rollover Resistance Using Fuzzy PID Controller of Active Anti-Roll Bar System

2018-12-20
Abstract The active anti-roll bar (AARB) system in vehicles has recently become one of the research hotspots in the field of vehicle technology to improve the vehicle’s active safety. In most off-road vehicles, high ground clearance is required while keeping all wheels in contact with the ground in order to improve traction and maintain load distribution among the wheels. A problem however arises in some types of the off-road vehicles when the vehicle is operated at high speeds on smooth roads. In such condition, the combination of the vehicle’s center of gravity position, large suspension stroke, and soft spring construction creates a stability problem, which could make the vehicle liable to rollover. This article analyzes a comparison of stability performance between passive and active anti-roll bar systems to improve rolling resistance. For active systems, two control strategies will be investigated. The conventional PID controller is firstly investigated and taken as a reference.
Journal Article

Hydro-Pneumatic Energy Harvesting Suspension System Using a PSO Based PID Controller

2018-08-01
Abstract In this article, a unique design for Hydro-Pneumatic Energy Harvesting Suspension HPEHS system is introduced. The design includes a hydraulic rectifier to maintain one-way flow direction in order to obtain maximum power generation from the vertical oscillation of the suspension system and achieve handling and comfort car drive. A mathematical model is presented to study the system dynamics and non-linear effects for HPEHS system. A simulation model is created by using Advanced Modeling Environment Simulations software (AMEsim) to analyze system performance. Furthermore, a co-simulation platform model is developed using Matlab-Simulink and AMEsim to optimize the PID controller parameters of the external variable load resistor applied on the generator by using Particle Swarm Optimization (PSO).
Journal Article

Force Transmission Characteristics for a Loaded Structural-Acoustic Tire Model

2018-10-23
Abstract Concerns about tire noise radiation arise partly from city traffic planning, environmental protection, and pedestrian safety standpoints, while from the vehicle passengers’ perspective, noise transmitted to the vehicle interior is more important. It is the latter concern that is addressed in this article. Sound-absorbing materials generally offer good absorption at higher frequencies, but the reduction of relatively low frequency, structure-borne tire noise is a continuing focus of many auto manufacturers. A tire’s internal, acoustic cavity resonance is a very strong contributing factor to tire-related structure-borne noise, and it can easily be perceived by passengers. Some reduction of vehicle cabin noise can be achieved through the insertion of sound-absorbing material in the tires. However, apart from the additional cost for such tires, there is also an increased complexity when repairing them because of the need to avoid damaging the sound-absorptive lining.
Journal Article

Explanation for Variability in Lower Frequency Structure-Borne Noise and Vibration: Roles of Rear Subframe Dynamics and Right-Left Spindle Phasing

2018-05-17
Abstract This investigation focuses on a class of rear suspension systems that contain both direct and intersecting structural paths from the tire contact patches to the vehicle body. The structural paths intersect through a dynamically active rear subframe structure. New experiments and computational models are developed and analyzed in this article to investigate the variability of structure-borne noise and vibration due to tire/road interactions in the lower- to mid-frequency regimes. Controlled operational experiments are conducted with a mass-production minivan on a chassis dynamometer equipped with rough road shells. Unlike prior literature, the controlled experiments are analyzed for run-run variations in the structure-borne noise up to 300 Hz in a single vehicle to evaluate the nature of excitations at the spindle as the key source of variation in the absence of significant manufacturing, assembly and instrumentation errors.
Journal Article

Enhanced Lateral and Roll Stability Study for a Two-Axle Bus via Hydraulically Interconnected Suspension Tuning

2018-11-19
Abstract The suspension system has been shown to have significant effects on vehicle performance, including handling, ride, component durability, and even energy efficiency during the design process. In this study, a new roll-plane hydraulically interconnected suspension (HIS) system is proposed to enhance both roll and lateral dynamics of a two-axle bus. The roll-plane stability analysis for the HIS system has been intensively explored in a number of studies, while only few efforts have been made for suspension tuning, especially considering lateral plane stability. This article aims to explore the integrated lateral and roll dynamics by suspension tuning of a two-axle bus equipped with HIS system. A ten-degree-of-freedom (DOF) lumped-mass vehicle model is integrated with either transient mechanical-hydraulic model for HIS or the traditional suspension components, namely, shock absorber and anti-roll bar (ARB).
Journal Article

Enhanced Coil Spring Modeling in Passenger Car Suspension for Improved Target Setting Process

2018-12-14
Abstract The problem addressed in this work is how to formulate accurate targets for coil springs in passenger car suspensions to ensure that the required ride height and wheel rate are achieved. The issue arises because suspensions often tend to introduce significant spring deformations other than a purely axial compression. Although these effects are quite common, their influence on suspension performance is still not well understood. To this purpose, a new enhanced spring model is presented. The theory behind the model is explained and the relationship between spring and suspension performance discussed in detail. To validate formulations, a series of numerical simulations has been carried out demonstrating the model accuracy. Finally, a novel approach to spring target setting is proposed based on this advanced spring model.
Journal Article

Development of an Empirical Spring Aid Model for Automotive Applications

2018-05-10
Abstract Spring aids are used to provide additional stiffness at the end of bump travel, preventing metal to metal contact. Commonly they are represented by nonlinear stiffness depending on displacement; however the main drawback of this approach is that it does not show any hysteretic behavior, hence they do not produce realistic force predictions differentiating between loading and unloading and energy absorbed is not calculated. Although introducing damping as a function of velocity generates some hysteresis, it does not generate realistic results for quasi-static and dynamic events; and measured data proves that velocity does not have a significant influence in the width of the loop. An empiric model can be build combining nonlinear stiffness and viscous damping, as a function of velocity, and also adding an additional term accounting for structural damping.
Journal Article

Determination of Influence of Parameters on Undercarriage Shock Absorber

2018-12-31
Abstract The simple oleo pneumatic (shock absorber) model was developed using the available computational fluid dynamics (CFD) program to understand how various parameters influence the performance of the undercarriage shock absorber. The study is divided into two parts: first part is focused on the influence of orifice geometry and the second part of the study is focused on the other parameters including chamber geometry. Both the studies are carried out using design of experiments (DOE) for the same output characteristics (response). In this study, the impacts on the flow behavior due to the orifice shapes are also studied. The results and the other outcomes are shown in the form of DOE parameters such as main effect plots and interaction plots.
Journal Article

Design, Analysis, Simulation and Validation of Automobile Suspension System Using Drive-Shaft as a Suspension Link

2018-04-18
Abstract With increasing demands for higher performance along with lower vehicle emissions, lightweight vehicle system construction is key to meet such demands. Suspension and transmission assemblies being the key areas for weight-reduction, we have designed a revolutionary new type of suspension system which combines the suspension links with the powertrain assembly and thus completely eliminates one suspension member. Less weight means lower fuel-consumption with improved passenger-comfort and road-holding due to reduction in unsprung mass. Elimination of a suspension link reduces the overall cost of material, machining & fabrication making our design cost-effective than existing setups. This paper deals with the design and implementation of of our concept. A working prototype is also constructed and tested which completely validates our design.
Journal Article

Active Suspension: Future Lessons from The Past

2018-06-18
Abstract Active suspension was a topic of great research interest near the end of last century. Ultimately broad bandwidth active systems were found to be too expensive in terms of both energy and financial cost. This past work, developing the ultimate vehicle suspension, has relevance for today’s vehicle designers working on more efficient and effective suspension systems for practical vehicles. From a control theorist’s perspective, it provides an interesting case study in the use of “practical” knowledge to allow “better” performance than predicted by theoretically optimal linear controllers. A brief history of active suspension will be introduced. Peter Wright, David Williams, and others at Lotus developed their Lotus modal control concept. In a parallel effort, Dean Karnopp presented the notion of inertial (Skyhook) damping. These concepts will be compared, the combination of these two distinctly different efforts will be discussed, and eventual vehicle results presented.
X