Search Results

Abstract An investigation into the pre-ashing of new gasoline particulate filters (GPFs) has demonstrated that the filtration efficiency of such filters can be improved by up to 30% (absolute efficiency improvement) when preconditioned using ash derived from a fuel-borne catalyst (FBC) additive. The additive is typically used in diesel applications to enable diesel particulate filter (DPF) regeneration and can be added directly into the fuel tank of the vehicle. This novel result was compared with ash derived from lube oil componentry, which has previously been shown to improve filtration efficiency in GPFs. The lube oil-derived ash utilized in this work improved the filtration efficiency of the GPF by −30%, comparable to the ash derived from the FBC additive.

Abstract As the automotive industry moves toward electrification, battery costs and vehicle range are two large issues that will delay this movement. These issues can be partially resolved through the use of series-hybrid vehicles, which can replace a portion of the batteries with a small engine that serves to recharge the battery. Given the size, weight, and operational constraints of this engine, a 2-stroke engine makes sense. Indeed, 2-stroke engines are currently being used for a number of applications including consumer products, small ground vehicles, boats, and drones. The technology has significantly improved to allow for reduced emissions and increased efficiency, especially through the use of direct injection. This article discusses the state of technology for 2-stroke engines and its application in series-hybrid vehicles. In particular, the use of a 2-stroke engine as a range extender provides significant benefit in range and cost over fully electric vehicles.

Abstract A numerical study using large-eddy simulations (LES) to reproduce and understand sources of cycle-to-cycle variation (CCV) in spark-initiated internal combustion engines (ICEs) is presented. Two relevantly different spark-ignition (SI) units, that is, a homogeneous-charge slow-speed single-cylinder research unit (the transparent combustion chamber (TCC)-III, Engine 1) and a stratified-charge high-revving speed gasoline direct injection (GDI) (Engine 2) one, are analyzed in fired operations. Multiple-cycle simulations are carried out for both engines and LES results well reproduce the experimentally measured combustion CCV. A correlation study is carried out, emphasizing the decisive influence of the early flame period variability (1% of mass fraction burnt (MFB1)) on the entire combustion event in both ICEs. The focus is moved onto the early flame characteristics, and the crucial task to determine the dominant causes of its variability (if any) is undertaken.

Abstract Diesel engines include systems for cooling, lubrication, and fuel injection and contain a variety of components. A malfunction in any of the engine systems or the presence of any faulty element influences engine performance and deteriorates its components. This research is concerned with the untimely appearance of vital cracks in the liners of a turbocharged heavy-duty Diesel engine. To find the root causes for premature failure, rigorous examinations through visual observations, material characterization, and metallographic investigations are performed. These include Scanning Electron Microscope (SEM) and Energy-Dispersive Spectroscopy (EDS), fracture mechanics analysis, and performance examination, which are also followed by Finite Element Moldings. To find the proper remedy to resolve the problem, drawing a precise and reliable picture of the engine’s operating conditions is required.

Abstract Environmental protection and the depletion of nonrenewable energy sources necessitate the search for the replacement of, among others, diesel fuel (Df) in diesel engines with renewable fuel without major structural changes. For this reason, vegetable oils are of interest as a possible fuel for this type of engine. Unfortunately, the physicochemical properties of vegetable oils differ significantly from Df. In addition to the boiling and freezing points, these properties include viscosity, density, and surface tension as well as wetting properties. For this reason, an attempt was made to modify these properties by adding n-hexane (Hex) and ethanol (Et) to canola oil (Co). The viscosity, density, surface tension, and wetting properties of Hex and Et are significantly different from those for Co.

Abstract The article discusses the possibilities of detecting defects in the marine diesel engine injection system on a selected example. Basing on statistical data, it was pointed out that these engines had a significant failure rate in relation to the failure rate of other machinery and equipment used on ships. First, it concerns damage of the elements of the injection systems. Therefore, basing on the results of the authors’ own research, the possibility of improving diagnostic methods of the injection system that can be used in the ship operation process was pointed out. First, high diagnostic effectiveness of the analysis of pressure changes measured in the injection system was pointed out here. At the same time, taking into account the difficulties of such measurement in the conditions of the ship’s power plant, it has been shown that very good diagnostic effects can be obtained by using indicator diagrams to calculate heat release characteristics.

Abstract The article describes the results achieved in developing a new diesel combustion system for passenger car application that, while capable of high power density, delivers excellent fuel economy through a combination of mechanical and thermodynamic efficiencies improvement. The project stemmed from the idea that, by leveraging the high fuel injection pressure of last generation common rail systems, it is possible to reduce the engine peak firing pressure (pfp) with great benefits on reciprocating and rotating components’ light-weighting and friction for high-speed light-duty engines, while keeping the power density at competitive levels. To this aim, an advanced injection system concept capable of injection pressure greater than 2500 bar was coupled to a prototype engine featuring newly developed combustion system. Then, the matching among these features has been thoroughly experimentally examined.

Abstract This study implements Flame Image Velocimetry (FIV), a diagnostic technique based on post-processing of high-speed soot luminosity images, to show the in-flame flow field development impacted by after-injection in a single-cylinder, small-bore optical diesel engine. Two after-injection cases with different dwell times between the main injection and after-injection, namely, close-coupled and long-dwell, as well as a main-injection-only case are compared regarding flow fields, flow vector magnitude, and turbulence intensity distribution. For each case, high-speed soot luminosity movies from 100 individual combustion cycles are recorded at a high frame rate of 45 kHz for FIV processing. The Reynolds decomposition using a spatial filtering method is applied to the obtained flow vectors so that bulk flow structures and turbulence intensity distributions can be discussed.

Abstract TOC

Abstract TOC

Abstract TOC

Abstract TOC

Abstract Driving schedule of every vehicle involves transient operation in the form of changing engine speed and load conditions, which are relatively unchanged during steady-state conditions. As well, the results from transient conditions are more likely to reflect the reality. So, the current research article is focused on analyzing the biofuel-like lemon peel oil (LPO) behavior under real-world transient conditions with fuel injection parameter MAP developed from steady-state experiments. At first, engine parameters and response MAPs are developed by using a response surface methodology (RSM)-based multi-objective optimization technique. Then, the vehicle model has been developed by incorporating real-world transient operating conditions. Finally, the developed injection parameters and response MAPs are embedded in the vehicle model to analyze the biofuel behavior under transient operating conditions.

Abstract The complex hydropneumatic electromagnetic coupling structure of the dual-fuel injector leads to its complicated injection process. The unknown problem of fuel injection characteristics limits the injector design and optimization process of combustion efficiency. Therefore, the scientific study of dual-fuel injection mechanism and online identification method is the key to grasping the diesel-gas coupled injection mechanism, and an important theoretical basis for advanced closed-loop control. In this study, an identification method for the time characteristics of the dual-fuel injector injection process is based on the injector inlet pressure, which can be applied to the diesel-natural gas co-direct injection engine. First, the cause and transfer process of diesel injection pressure waves were analyzed based on the Riemann invariant theory.

Abstract An ongoing challenge with Gasoline engines is achieving rapid activation of the three-way catalyst during cold starts in order to minimize pollutant emissions. Retarded combustion is an effective way in achieving rapid light-up of the three-way catalyst and can be facilitated by stratified charge using late fuel injection. This, however, provides insufficient time for fuel entrainment with air, resulting in locally fuel-rich diffusion combustion. Employing a split injection strategy can help tackle these issues. The effects of a split injection strategy, using a high-pressure Solenoid injector, on the in-cylinder charge formation are investigated in the current study. The studies are performed inside an optical Gasoline engine using high-speed particle image velocimetry (PIV) in the central tumble and Omega tumble planes, by means of a high-speed laser and camera operating at a repetition rate of 10 kHz.

Abstract The broadband aeroacoustics of a side mirror is investigated with a stochastic noise source method and compared to scale-resolving simulations. The setup based on an already existing work includes two geometrical variants with a plain series side mirror and a modified mirror with a forward-facing step mounted on the inner side. The aeroacoustic near- and farfield is computed by a hydrodynamic–acoustic splitting approach by means of a perturbed convective wave equation. Aeroacoustic source terms are computed by the Fast Random Particle-Mesh method, a stochastic noise source method modeling velocity fluctuations in time domain based on time-averaged turbulence statistics. Three RANS models are used to provide input data for the Fast Random Particle-Mesh method with fundamental differences in local flow phenomena.

Abstract High fuel injection pressure systems for Gasoline Direct Injection (GDI) engines have become widely used in passenger car engines to reduce emissions of particulates and pollutant gases. Current commercial systems operate at pressures of up to 450 bar, but several studies have examined the use of injection pressures above 600 bar, and some have even used pressures around 1500 bar. These works revealed that high injection pressures have numerous benefits including reduced particulate emissions, but there is still a need for more data on the possible benefits of injection pressures above 1000 bar. This article presents spray and engine data from a comprehensive study using several measurement techniques in a spray chamber and optical and metal engines. Shadowgraph imaging and Phase Doppler Interferometry (PDI) were used in a constant volume chamber to interpret spray behavior. Particle Image Velocimetry (PIV) was used to capture near-nozzle air entrainment.

Abstract Previous studies have shown that injector aging adversely affects the diesel engine spray formation and combustion. It has also been shown that the oxygenated fuel additive tripropylene glycol monomethyl ether (TPGME) can lower soot emissions. In this study, the effects of injector aging and TPGME on the late-cycle oxidation of soot were investigated using laser diagnostic techniques in a light-duty optical diesel engine at two load conditions. The engine was equipped with a quartz piston with the same complex piston geometry as a production engine. Planar laser-induced incandescence (LII) was used to obtain semiquantitative in-cylinder two-dimensional (2D) soot volume fraction (fv ) distributions using extinction measurements. The soot oxidation rate was estimated from the decay rate of the in-cylinder soot concentration for differently aged injectors and for cases with and without TPGME in the fuel.

Abstract Particulate formation was studied under homogeneous-intent stoichiometric operating conditions when ethanol-blended (E10) or methanol-blended (M20) gasoline fuel was injected during intake stroke of a 4-stroke direct-injected engine. The engine was tested at wide open throttle under naturally aspirated conditions for a speed-load of 1500 rev/min and 9.8 bar indicated mean effective pressure. In-cylinder soot observations and exhaust soot measurements were completed for different fuel rail pressures, injection timings, coolant and piston temperatures of the optical engine. Fuel delivery settings were tested with both single and split injections during intake stroke. The target piston temperature of the optical engine was attained using pre-determined number of methane port fuel injection firing cycles. Overall, the in-cylinder soot observations correlated well with the engine-out soot measurements. A warmer cylinder head favored soot reduction for both fuels.

Abstract The airline industry faces a crisis in the future as consumer demand is increasing, but the environmental effects and depleting resources of kerosene mean that growth is unsustainable. Hydrogen is touted as the leading candidate to replace kerosene, but it needs significant technological and economical endeavors. In such a scenario, cryogenic liquid hydrogen (LH2) is predicted to be the most feasible method of using hydrogen. The major challenge of LH2 as an aircraft fuel is that it requires approximately four times the storage volume of kerosene—due to its lower density. Thus the design of cryogenic storage tanks to handle larger quantities of fuel is becoming increasingly important. But the increase in drag associated with larger storage tanks causes an increase in fuel consumption. Hence, this paper aims to evaluate the aerodynamic performance of different storage configurations and aid in the selection of an economic and efficient storage system.