Refine Your Search

Topic

Search Results

Journal Article

WM-LES-Simulation of a Generic Intake Port Geometry

2018-06-18
Abstract Fluid mechanical design of the cylinder charge motion is an important part of an engine development. In the present contribution an intake port geometry is proposed that can be used as a test case for intake port flow simulations. The objective is to fill the gap between generic test cases, such as the backward facing step or the sudden expansion, and simulations of proprietary intake ports, which are barely accessible in the community. For the intake geometry measurement data was generated on a flow-through test bench and a wall-modeled LES-simulation using a hybrid RANS/LES approach for near-wall regions was conducted. The objective is to generate and analyze a reference flow case. Since mesh convergence studies are too costly for scale resolving approaches only one simulation was done, but on a very fine and mostly block-structured numerical mesh to achieve minimal numerical dissipation.
Journal Article

Understanding the Origin of Cycle-to-Cycle Variation Using Large-Eddy Simulation: Similarities and Differences between a Homogeneous Low-Revving Speed Research Engine and a Production DI Turbocharged Engine

2018-12-14
Abstract A numerical study using large-eddy simulations (LES) to reproduce and understand sources of cycle-to-cycle variation (CCV) in spark-initiated internal combustion engines (ICEs) is presented. Two relevantly different spark-ignition (SI) units, that is, a homogeneous-charge slow-speed single-cylinder research unit (the transparent combustion chamber (TCC)-III, Engine 1) and a stratified-charge high-revving speed gasoline direct injection (GDI) (Engine 2) one, are analyzed in fired operations. Multiple-cycle simulations are carried out for both engines and LES results well reproduce the experimentally measured combustion CCV. A correlation study is carried out, emphasizing the decisive influence of the early flame period variability (1% of mass fraction burnt (MFB1)) on the entire combustion event in both ICEs. The focus is moved onto the early flame characteristics, and the crucial task to determine the dominant causes of its variability (if any) is undertaken.
Journal Article

Study of Temperature Distribution and Parametric Optimization during FSW of AA6082 Using Statistical Approaches

2019-02-01
Abstract In this article, Al-Mg-Si-Mn alloy (AA6082) is butt joined by employing friction stir welding (FSW). The mechanical and metallurgical properties of joints are analyzed by conducting tensile and microhardness testing, respectively. To measure the temperature at different locations, eight thermocouples (L-shaped k-type) are placed at equal distance from the centerline. Least square method attempts to calculate the temperature at the centerline of joints. The process parameters are also optimized using Taguchi’s five-level experimental design. The optimum process parameters are determined, employing ultimate tensile strength (UTS) as a response parameter. A statistical test “analysis of variance” is used to check the adequacy of the model. It has been observed that rotational speed and feed rate are the predominant factors for UTS and microhardness.
Journal Article

Soot Observations and Exhaust Soot Comparisons from Ethanol-Blended and Methanol-Blended Gasoline Combustion in a Direct-Injected Engine

2018-05-07
Abstract Particulate formation was studied under homogeneous-intent stoichiometric operating conditions when ethanol-blended (E10) or methanol-blended (M20) gasoline fuel was injected during intake stroke of a 4-stroke direct-injected engine. The engine was tested at wide open throttle under naturally aspirated conditions for a speed-load of 1500 rev/min and 9.8 bar indicated mean effective pressure. In-cylinder soot observations and exhaust soot measurements were completed for different fuel rail pressures, injection timings, coolant and piston temperatures of the optical engine. Fuel delivery settings were tested with both single and split injections during intake stroke. The target piston temperature of the optical engine was attained using pre-determined number of methane port fuel injection firing cycles. Overall, the in-cylinder soot observations correlated well with the engine-out soot measurements. A warmer cylinder head favored soot reduction for both fuels.
Journal Article

Sliding Mode Control of Hydraulic Excavator for Automated Grading Operation

2018-06-07
Abstract Although ground grading is one of the most common tasks that hydraulic excavators perform in typical work sites, proper grading is not easy for less-skilled operators as it requires coordinated manipulation of multiple hydraulic cylinders. In order to help alleviate this difficulty, automated grading systems are considered as an effective alternative to manual operations of hydraulic excavators. In this article, a sliding mode controller design is presented for automated grading control of a hydraulic excavator. First, an excavator manipulator model is developed in Simulink by using SimMechanics and SimHydraulics toolboxes. Then, a sliding mode controller is designed to control the manipulator to trace a predefined trajectory for a grading task. For a comparison study, a PI controller is used to control the manipulator to perform a grading task following the same desired trajectory and the performance is compared with those obtained by the sliding mode controller.
Journal Article

Role of Piston Bowl Shape to Enhance Late-Cycle Soot Oxidation in Low-Swirl Diesel Combustion

2019-04-25
Abstract Late-cycle soot oxidation in heavy-duty (HD) diesel engine low-swirl combustion was investigated using single-cylinder engine and spray chamber experiments together with engine combustion simulations. The in-cylinder flow during interactions between adjacent flames (flame-flame events) was shown to have a large impact on late-cycle combustion. To modify the flame-flame flow, a new piston bowl shape with a protrusion (wave) was designed to guide the near-wall flow. This design significantly reduced soot emissions and increased engine thermodynamic efficiency. The wave’s main effect was to enhance late-cycle mixing, as demonstrated by an increase in the apparent rate of heat release after the termination of fuel injection. Combustion simulations showed that the increased mixing is driven by enhanced flow re-circulation, which produces a radial mixing zone (RMZ).
Journal Article

Response of Austempering Heat Treatment on Microstructure and Mechanical Property in Different Zones of As-Welded Ductile Iron (DI)

2018-05-08
Abstract Sound ductile iron (DI) welded joints were performed using developed coated electrode and optimized welding parameters including post weld heat treatment (PWHT).Weldments consisting of weld metal, partially melted zone (PMZ), heat affected zone (HAZ) and base metal were austenitized at 900 °C for 2 hour and austempered at 300 °C and 350 °C for three different holding time (1.5 hour, 2 hour and 2.5 hour). In as-weld condition, microstructures of weld metal and PMZ show ledeburitic carbide and alloyed pearlite, but differ with their amount. Whereas microstructure of HAZ shows pearlite with some ledeburitic carbide and base metal shows only ferrite.
Journal Article

Residual Stresses and Plastic Deformation in Self-Pierce Riveting of Dissimilar Aluminum-to-Magnesium Alloys

2018-05-08
Abstract In this work, the complex relationship between deformation history and residual stresses in a magnesium-to-aluminum self-pierce riveted (SPR) joint is elucidated using numerical and experimental approaches. Non-linear finite element (FE) simulations incorporating strain rate and temperature effects were performed to model the deformation in the SPR process. In order to accurately capture the deformation, a stress triaxiality-based damage material model was employed to capture the sheet piercing from the rivet. Strong visual comparison between the physical cross-section of the SPR joint and the simulation was achieved. To aid in understanding of the role of deformation in the riveting process and to validate the modeling approach, several experimental measurements were conducted. To quantify the plastic deformation from the piercing of the rivet, micro hardness mapping was performed on a cross-section of the SPR joint.
Journal Article

Partial Transparency of Advanced Compression Ignition Combustion Chamber Deposits, Its Impact on Combustion Chamber Wall Temperatures and Application to Thermal Barrier Coating Design

2018-04-18
Abstract The proven impact of combustion chamber deposits, CCD, on advanced compression ignition, ACI, combustion strategies has spurred researchers to develop thermal barrier coatings, TBC, which can mimic CCD benefits on combustion efficiency and operational range expansion. However, application of TBCs within multi-mode engines exposes them to non-negligible soot radiation. In the present paper, the impact of radiation heat transfer on combustion chamber deposits is studied. The morphological construction of the combustion chamber deposit layer is shown to be partially transparent to radiation heat transfer, drawing corollaries with ceramic-based TBCs. Additional experimentation eliminates the optical transparency of CCD to reveal an “effective radiation penetration depth” facilitated by open surface porosity. The effective radiation penetration depth is then utilized to establish the relative communicating porosity of CCD and a magnesium zirconate TBC.
Journal Article

Parameter Sensitivity and Process Time Reduction for Friction Element Welding of 6061-T6 Aluminum to 1500 MPa Press-Hardened Steel

2018-12-14
Abstract Conventional fusion joining techniques pervasive in the automotive industry are unable to effectively join aluminum and steel. To solve this problem, a technique termed friction element welding (FEW) has been developed, which is able to join any nonferrous top sheet material to a base steel layer, independent of the base layer strength. FEW works on the same principles as friction welding, as a steel element is pushed and rotated against a nonferrous top sheet to create frictional energy which softens and flows the material around the fastener shaft and under the fastener head, exposing the steel below. The element then contacts the steel and bonds through traditional friction welding. FEW is a four-step process (penetration, cleaning, welding, compression), with two to four parameters (endload, spindle speed, displacement transition, time transition) controlling each step.
Journal Article

Optimization of WEDM Cutting Parameters on Surface Roughness of 2379 Steel Using Taguchi Method

2018-04-07
Abstract Surface roughness is one of the important aspects in producing quality die. Wire Electrical Discharge Machine (WEDM) is commonly used in tool and die fabrication, since the die material is usually difficult to cut using traditional metal removal processes. Selection of optimal WEDM cutting parameters is crucial to obtain quality die finish. In this study, 2379 steel which equivalent to SKD 11 is selected as the die material. Four main WEDM cutting parameters, namely, pulse duration (A), pulse interval (B), servo voltage (C), ignition pulse current (D), were experimentally evaluated for both main cut and multiple trim cuts using Taguchi Method. Taguchi’s L9 orthogonal array is employed for experimental design and analysis of variance (ANOVA) was used in recognizing levels of significance of WEDM cutting parameters.
Journal Article

Numerical Prediction of Various Failure Modes in Spotweld Steel Material

2018-05-11
Abstract Crash simulation is targeted mainly carried out by the collision regulations FMVSS simulation to identify problems in vehicle structures. A modern car structure consist of several thousand weld-type connections, and failure in these connections plays an important role for the crashworthiness of the vehicle. Therefore accurate modeling of these connections is important for the automotive industry in order to improve Vehicle collision characteristics. In pursuit of this key requirement, we introduced a proper methodology for the development detailed weld model to study structural response of the weld when the applied load range is beyond the yield strength. Three-dimensional finite element (FE) models of spot welded joints are developed using the LS-Dyna FE code. In this process the force estimation model of spot welds is explained. The results from this paper shows good agreement between the simulations and the tests.
Journal Article

Multi-Objective Optimization of Counterweights: A Substitute for the Balance Shaft or Mass Unbalancing in Three-Cylinder Engines

2018-10-18
Abstract Three-cylinder engines were launched, given the increasing demand for improved fuel economy and efficiency along with reduced friction and weight. Unlike four-cylinder engines, these engines are not naturally balanced. So, in order to compete with four-cylinder engines, some methods to solve this inherent weakness, such as balance shaft, mass unbalancing of flywheel and crankshaft pulley, or counterweights configuration (angular orientation and correction amount), have been used. Considering the undesirable characteristics of the balance shaft, such as cost, weight, friction, and noise, as well as dynamically inappropriate mass unbalancing method, this research proposes multi-objective optimization of counterweights to reduce vibrations.
Journal Article

Mixture Distributions in Autonomous Decision-Making for Industry 4.0

2019-05-29
Abstract Industry 4.0 is expected to revolutionize product development and, in particular, manufacturing systems. Cyber-physical production systems and digital twins of the product and process already provide the means to predict possible future states of the final product given the current production parameters. With the advent of further data integration coupled with the need for autonomous decision-making, methods are needed to make decisions in real time and in an environment of uncertainty in both the possible outcomes and in the stakeholders’ preferences over them. This article proposes a method of autonomous decision-making in data-intensive environments, such as a cyber-physical assembly system. Theoretical results in group decision-making and utility maximization using mixture distributions are presented. This allows us to perform calculations on expected utility accurately and efficiently through closed-form expressions, which are also provided.
Journal Article

Machining Quality Analysis of Powertrain Components Using Plane Strain Finite Element Cutting Models

2018-05-07
Abstract Finite Element Analysis (FEA) of metal cutting is largely the domain of research organizations. Despite significant advances towards accurately modelling metal machining processes, industrial adoption of these advances has been limited. Academic studies, which mainly focused on orthogonal cutting, fail to address this discrepancy. This paper bridges the gap between simplistic orthogonal cutting models and the complex components typical in the manufacturing sector. This paper outlines how to utilize results from orthogonal cutting simulations to predict industrially relevant performance measures efficiently. In this approach, using 2D FEA cutting models a range of feed, speed and rake angles are simulated. Cutting force coefficients are then fit to the predicted cutting forces. Using these coefficients, forces for 3D cutting geometries are calculated.
Journal Article

Literature Review on the Effects of Organometallic Fuel Additives in Gasoline and Diesel Fuels

2018-04-18
Abstract A literature review was conducted and fuel survey data were obtained to identify the use of metallic fuel additives (MFAs) within market fuels and determine their effects on engines, exhaust systems, and vehicle performance. The primary focus was on modern vehicles equipped with on-board diagnostic (OBD) systems and advanced emissions control systems. For gasoline, this includes vehicles categorized as National Low Emission Vehicles (NLEV) and Tier 2 or beyond in the U.S., and Euro-3 through Euro-6 in the EU. For diesel, this includes engines/vehicles with original equipment manufacturer (OEM)-equipped oxidation catalysts and diesel particulate filters. The literature search of peer-reviewed papers and other publicly available articles returned over 100 items relevant to the use of organometallic fuel additives, but did not provide significant evidence of widespread use of MFAs in either gasoline or diesel fuels.
Journal Article

Limitations of Two-Stage Turbocharging at High Flight Altitudes

2018-09-17
Abstract High-altitude long-endurance (HALE) unmanned aerial vehicles (UAVs) are used for high flight altitudes, which enable low drag and fast flight with minimal fuel consumption. Two-stage turbocharging is necessary to sustain sea-level power at high flight altitudes. In this study, the limitations of two-stage turbocharging at high flight altitudes typical for HALE UAVs are analyzed for the first time. The obtained results show that the minimum available engine power increases as the altitude rises. This will limit the ability of the aircraft to descend rapidly. Furthermore, at high altitudes, if a lower operating point is required for a fast descent, further recovery to full power for climbing or cruising could be unavailable. In the latter cases, a lower altitude must be reached before full power would be available again. A basic algorithm for the assessment and analysis of the limitations of UAV engines with two-stage turbochargers operating at high altitudes is suggested.
Journal Article

Joint Mechanism and Prediction of Strength for a Radial Knurling Connection of Assembled Camshaft Using a Subsequent Modeling Approach

2018-06-25
Abstract Knurling joint applied in assembled camshaft has developed rapidly in recent years, which have exhibited great advantages against conventional joint methods in the aspects of automation, joint precision, thermal damage, noise, and near net shape forming. Both quality of assembly process and joint strength are the key requirements for manufacturing a reliable assembled camshaft. In this article, a finite element predictive approach including three subsequent models (knurling, press-fit and torsion strength) has been established. Johnson-Cook material model has been used to simulate the severe plastic deformation of the material. The residual stress field calculated from the knurling process was transferred as initial condition to the press-fit model to predict the press-fit load. The predicted press-fit load, torque strength and displacement of cam profile before failure were calculated.
Journal Article

Investigation of Residual Stresses in Cold-Formed Steel Sections with Nonlinear Strain-Hardened Material Model

2018-09-17
Abstract In this article, forming residual stresses in cold-formed small-radius corner sections are analytically predicted with the consideration of the shift in the neutral axis and the nonlinear strain-hardened material model. The predicted forming stress results in the transverse direction show a trend of increased compressive residual stress in the outer surface and reduced tensile residual stress in the inner surface as the corner radius-to-thickness ratio increases in small-radius bends. In the longitudinal direction, there is no significant change in the residual stress values observed in the inner and outer surfaces with respect to an increase in corner radius-to-thickness ratios. But a considerable decrease in compressive residual stress and an increase in tensile stress values are observed in the midsection areas with an increase in the corner radius-to-thickness ratio.
Journal Article

Internal Combustion Engine Cylinder Volume Trace Deviation

2018-04-18
Abstract Heat release analysis is a widely used cylinder pressure-based method for evaluating combustion in engine development, and it is also being investigated as a means to control engine combustion. Heat release analysis has been shown to be sensitive to errors in the calculated cylinder volume, but despite this one of the most common assumptions is that the cylinder volume is nominal and can be calculated solely by the geometrical relations among the measures of the engine components. During engine operation, the components surrounding the combustion chamber are exposed to thermal forces, pressure forces, and mass forces from the reciprocating components. Due to these forces, the components will deform and the volume of the combustion chamber will deviate from its ideal volume. The volume will also be affected by the production tolerances of the engine.
X