Search Results

Abstract The use of appropriate loads and regulations is of great importance in weld fatigue assessment of rail on-track maintenance equipment and similar vehicles for optimized design. The regulations and available loads, however, are often generalized for several categories, which proves to be overly conservative for some specific categories of machines. EN (European Norm) and AAR (Association of American Railroads) regulations play a pivotal role in determining the applicable loads and acceptance criteria within this study. The availability of track-induced fatigue load data for the cumulative damage approach in track maintenance machines is often limited. Consequently, the FEA-based validation of rail track maintenance equipment often resorts to the infinite life approach rather than cumulative damage approach for track-induced travel loads, resulting in overly conservative designs.

Abstract The project of lean management is implemented in General Motors India Private Limited, Pune, India plant. The aim of the project is to improve manpower utilization by removing seven types of wastes using lean management system in kitting process. Lean manufacturing or management is the soul of Just-In-Time philosophy and is not new in Automobile manufacture sector where it born. Kitting area is analogs to the modern supermarket where required components, parts, consumables, subassemblies are kept in bins. These bins are placed in racks so that choosing right part at right time can be achieved easily. Video recording, in-person observation, feedback from online operators and other departments such as maintenance, control, supply chain etc. are taken. It is observed that the work content performed by current strength of operators can be performed by less number of operators. After executing this project, it was possible to reduce one operator and increase manpower utilization.

Abstract One of the key problems of battery electric vehicles is the risk of severe range reduction in winter conditions. Technologies such as heat pump systems can help to mitigate such effects, but finding adequate heat sources for the heat pump sometimes can be a problem, too. In cold ambient conditions below −10°C and for a cold-soaked vehicle this can become a limiting factor. Storing waste heat or excess cold when it is generated and releasing it to the vehicle thermal management system later can reduce peak thermal requirements to more manageable average levels. In related architectures it is not always necessary to replace existing electric heaters or conventional air-conditioning systems. Sometimes it is more efficient to keep them and support them, instead. Accordingly, we show, how latent heat storage can be used to increase the efficiency of existing, well-established heating and cooling technologies without replacing them.

Abstract Sustainable practices are taking precedence across many industries, as evident from their shift towards the use of environmentally responsible materials, such as natural fiber-reinforced acrylated epoxidized soybean oil (NF-AESO). However, due to the lower reactivity of AESO, the curing reaction usually requires higher temperatures and longer curing time (e.g., 150°C for 6-12 h), thus making the entire process unsustainable. In this study, we demonstrate the potential power of photons towards manufacturing NF-AESO composites in a sustainable manner at room temperature (RT) within 10 min. Two photoinitiators, i.e., the 2,2-dimethoxy phenylacetophenone (DMPA) and 1-hydroxycyclohexyl phenyl ketone (HCPK), were evaluated and compared with the thermal initiator, i.e., tert-butyl perbenzoate (TBPB). Based on the mechanical performance of the AESOs, the photoinitiation system for NF-AESO was optimized.

Abstract This article focuses on the development of a two-way coupled methodology to predict gear temperature of oil jet lubricated transmissions using commercial software for computational fluid dynamics simulation. The proposed methodology applies an overset mesh technique to model the gear interlocking motion, multiphase of air-oil mixture, and heat transfer. Two gear pairs were used to develop and validate the methodology, an overdrive helical gear pair of a commercial vehicle transmission and a standard spur gear pair. Different oil jet lubrication methods were investigated using the proposed methodology, such as oil jet directed at the into-mesh position and at the out-of-mesh position. This investigation showed that out of mesh lubrication direction shows better cooling performance which is in well agreement with previous studies of literature.

Abstract The lack of traceability in today’s supply-chain system for auto components makes counterfeiting a significant problem leading to millions of dollars of lost revenue every year and putting the lives of customers at risk. Traditional solutions are usually built upon hardware such as radio-frequency identification (RFID) tags and barcodes, and these solutions cannot stop attacks from supply-chain (insider) parties themselves as they can simply duplicate products in their local database. This industry-academia collaborative work studies the benefits and challenges associated with the use of distributed ledger (or blockchain) technology toward preventing counterfeiting in the presence of malicious supply-chain parties. We illustrate that the provision of a distributed and append-only ledger jointly governed by supply-chain parties themselves makes permissioned blockchains such as Hyperledger Fabric a promising approach toward mitigating counterfeiting.

Abstract This work develops a comprehensive thermohydrodynamic (THD) model for high-speed squeeze film dampers (SFDs) in the presence of lubricant inertia effects. Firstly, the generalized expression for Reynolds equation is developed. Additionally, in order to reduce the complexity of the hydrodynamic equations, an average radial viscosity is defined and integrated into the equations. Subsequently, an inertial correction to the pressure is incorporated by using a first-order perturbation technique to represent the effect of lubricant inertia on the hydrodynamic pressure distribution. Furthermore, a thermal model, including the energy equation, the Laplace heat conduction equations in the surrounding solids (i.e. the journal and the bush), and the thermal boundary conditions at the interfaces is constructed. Moreover, the system of partial differential hydrodynamic and thermal equations is simultaneously solved by using an iterative numerical algorithm.

Abstract Increasing thermal and fuel efficiency in Internal Combustion Engines (ICEs) requires thorough investigations on the combustion process and its thermodynamics. The first law of thermodynamics expresses the balance of the energy, while the second law specifies the maximum achievable work. In this article, Low-Temperature Combustion (LTC) strategies, including Homogeneous Charge Compression Ignition (HCCI), Reactivity Controlled Compression Ignition (RCCI), Partially Premixed Combustion (PPC), and Direct Dual-Fuel Stratification (DDFS) were analyzed by the first and second law approaches, and they were compared with ideal-diesel cycle and Conventional Diesel Combustion (CDC). HCCI and RCCI had the highest exergy efficiency of 50.8% and 49.2%, respectively, compared to other cases, and exergy destruction in these cases was the lowest (25.3% and 27.5%, respectively).

Abstract High technology expertise and strong advancement in electric vehicles and Lithium (Li)-ion battery devices and systems have increased the speed of development and application of new equipment. It is reported that Li-ion battery life reduces almost by 60 days per degree temperature rise in an operational temperature of 30°C to 40°C, which makes cooling a high priority. The current study focuses on cooling the battery system using Phase Change Material (PCM) placed as bands of different dimensions around the prismatic battery. Eight novel designs of varying dimensions were constructed for three-volume scenarios. The heat generations considered in this study are 6,855 W/m3, 12,978 W/m3, 19,100 W/m3, and 63,970 W/m3. The data obtained was trained using an artificial neural network (ANN), and an equation was attained to fit the data. The optimum placement of PCM with respect to the number of bands and dimensions was achieved through a Genetic Algorithm.

Abstract An accurate and rapid thermal model of an axle-brake system is crucial to the design process of reliable braking systems. Proper thermal management is necessary to avoid damaging effects, such as brake fade, thermal cracking, and lubricating oil degradation. In order to understand the thermal effects inside of a lubricated braking system, it is common to use Computational Fluid Dynamics (CFD) to calculate the heat generation and rejection. However, this is a difficult and time-consuming process, especially when trying to optimize a braking system. This article uses the results from several CFD runs to train a Stacked Ensemble Model (SEM), which allows the use of machine learning (ML) to predict the systems’ temperature based on several input design parameters. The robustness of the SEM was evaluated using uncertainty quantification.

Abstract Off-highway equipment are subjected to diverse environmental conditions, severe duty cycles, and multiple simultaneous operations. Due to its continuous, high-power adverse operating conditions, equipment are exposed to high thermal loads, which result in the deterioration of its performance and efficiency. This article describes a model-based system simulation approach for thermal performance evaluation of a self-propelled off-highway vehicle. The objective of developing the simulation model including thermal fidelity is to quantify the impact of thermal loads on vehicular system/subsystems performance. This article also describes the use of simulation models for driving architectural design decisions and virtual test replication in all stages of product development.

Abstract Batteries have profound importance in today’s world as they are useful in powering the future without fossil fuels because of their properties, such as high energy density and durability. Volumetric and packing efficiency is better for a prismatic cell when compared with a cylindrical cell, whereas heat will be higher for a prismatic cell. This makes them a hot topic of research and development (R&D), with researchers finding ever more ways to improve. In this work, an attempt is made to study the effect of various mini-channel configurations on prismatic cell thermal management including the effect of C-rate, coolant flow rate, and coolant inlet temperature on temperature gradient and maximum cell temperature using ANSYS-Fluent by using an equivalent circuit model (ECM) in multi-scale multidimensional (MSMD) add-on module.

Abstract To protect ship equipment of river and sea transport, it is suggested to use polymeric protective coatings based on epoxy diane oligomer ED-20, polyethylene polyamine (PEPA) curing agent and filler, which is a departure from industrial production. Thus the purpose of the work is analysis of major dependency of the properties on the content of fillers that allowed to revealed the critical filler content (furnace black) in composites to form a protective coating with the required set of characteristics. The infrared (IR) spectral analysis was used to investigate the presence of bonds on the surface of particles of the PM-75 furnace black, which allows us to assess the degree of cross-linking of the polymer. The influence of the content of dispersed furnace black on the physicomechanical and thermophysical properties and the structure of the protective coating is investigated.

Abstract The causes of failure due to cracking in the resistance spot welding of the advanced high-strength steels dual-phase 590 (DP590) were investigated using scanning electron microscopy (SEM), optical microscopy, and the tensile-shear test. The results showed that by increasing the current amount, the formation of the melting zone occurred in the heat-affected zone, leading to the cracking in this area, reducing the tensile strength and decreasing the mechanical properties; the initiation and growth of cracking and failure in this region also happened. In the heat-affected zone, by increasing the current amount with the softening phenomenon, the recrystallized coarse grains also occurred, eventually resulting in the loss of mechanical properties. The results of the tensile-shear test also indicated that by increasing the current up to 12 kA, the strength was raised, but the ductility was reduced.

Abstract Heavy commercial vehicles play an important role in creating the trade and economic balance of countries. Also, the durability and safety of heavy commercial vehicles come to the fore. Heavy commercial vehicles consist of two parts. These are the chassis area with the equipment that allows the vehicle to move and the cabin section where the driver is located. The cabin area is the most important area that ensures the highest level of driver safety. Considering that the production of trucks is increasing day by day, it is inevitable for companies to increase their R&D activities in the field of cabin and cabin suspension systems for much safer, durable, and comfortable trucks. This study aims to determine the safe torque value of the fasteners and their assembly sequence of the Cab Suspension Console, which is one of the most important connection parts in a truck and which can cause a fatal accident by breaking.

Abstract The increase in worldwide awareness of environmental issues has necessitated the air transport industry to drastically reduce carbon dioxide emissions. To meet this goal, one solution is the electrification of aircraft propulsion systems. In particular, single-aisle aircraft with partial turboelectric propulsion with approximately 150 passenger seats in the 2030s are the focus. To develop a single-aisle aircraft with partial turboelectric propulsion, an air-cooled interior permanent magnet (IPM) motor with an output of 2 MW is desired. In this article, mathematical system equations that describe heat transfer inside the target air-cooled IPM motor are formulated, and their mathematical analytical solutions are obtained.

Abstract TOC

Abstract TOC

Abstract Results from a thermal survey measurement campaign on a four-cylinder Volvo engine was presented in Part I of this article. The focus was predominantly on heat transfer in the engine coolant jacket. This part presents numerical modeling focused specifically on the coolant flow and associated heat transfer in the coolant jacket using computational fluid dynamics (CFD), as a part of a high-resolution complete engine 3D conjugate heat transfer (CHT) model. With local nucleate boiling being an indispensable phenomenon in high power density engines, a dedicated boiling model is essential and is to be used in conjunction with CFD while analyzing heat transfer in the coolant jacket. This article validates a new boiling model with data obtained from the extensive thermal survey measurements, presented in Part I.

Abstract Nucleate boiling occurs inadvertently in the coolant jacket of high power density internal combustion engines, especially in vicinity of regions experiencing high thermal loads. Occurrence of boiling can be beneficial and be an efficient way to improve heat transfer locally near hot spots, but excessive boiling can be detrimental to structural integrity of the engine. While most of the efforts to understand boiling have been focused on experiments in simplified geometries, this article presents results from thermal survey measurement on a production engine. The purpose of the measurement campaign is to understand the intensity and extent of nucleate boiling occurring in different parts of the engine coolant jacket. This is achieved by sweeping across different input parameters, such as engine operating load point, cooling system operating pressure, coolant flow rate, and coolant inlet temperature.