Search Results

Abstract The use of appropriate loads and regulations is of great importance in weld fatigue assessment of rail on-track maintenance equipment and similar vehicles for optimized design. The regulations and available loads, however, are often generalized for several categories, which proves to be overly conservative for some specific categories of machines. EN (European Norm) and AAR (Association of American Railroads) regulations play a pivotal role in determining the applicable loads and acceptance criteria within this study. The availability of track-induced fatigue load data for the cumulative damage approach in track maintenance machines is often limited. Consequently, the FEA-based validation of rail track maintenance equipment often resorts to the infinite life approach rather than cumulative damage approach for track-induced travel loads, resulting in overly conservative designs.

Abstract Personal watercraft (PWC) users and other high-speed watersports participants have sustained rectal and vaginal injuries during falls into the water, herein referred to as water intrusion injuries (WIIs). WIIs result from the rapid introduction of water into these lower body cavities causing injury to the soft tissues of the perineum, rectum, and vagina. While case studies of injured water-skiers and PWC users are reported in the literature, there is little information related to passenger kinematics and pressure exposure during a rearward fall from a PWC. The results of an experimental study of passenger falls from two “high-performance” PWC are presented herein. A human passenger was caused to fall rearward as the PWC was accelerated at maximum throttle starting from idle speed (≈3–4 mph) and planing speeds of ≈20–30 mph. The subject passenger fell from the aft seat position and while standing on the rear platform.

Abstract The water droplet erosion (WDE) on high-speed rotating wheels appears in several engineering fields such as wind turbines, stationary steam turbines, fuel cell turbines, and turbochargers. The main reasons for this phenomenon are the high relative velocity difference between the colliding particles and the rotor, as well as the presence of inadequate material structure and surface parameters. One of the latest challenges in this area is the compressor wheels used in turbochargers, which has a speed up to 300,000 rpm and have typically been made of aluminum alloy for decades, to achieve the lowest possible rotor inertia. However, while in the past this component was only encountered with filtered air, nowadays, due to developments in compliance with tightening emission standards, various fluids also collide with the spinning blades, which can cause mechanical damage.

Abstract This study evaluates the applicability of the Octane Index (OI) framework under conventional spark ignition (SI) and “beyond Research Octane Number (RON)” conditions using nine fuels operated under stoichiometric, knock-limited conditions in a direct injection spark ignition (DISI) engine, supported by Monte Carlo-type simulations which interrogate the effects of measurement uncertainty. Of the nine tested fuels, three fuels are “Tier III” fuel blends, meaning that they are blends of molecules which have passed two levels of screening, and have been evaluated to be ready for tests in research engines. These molecules have been blended into a four-component gasoline surrogate at varying volume fractions in order to achieve a RON rating of 98. The molecules under consideration are isobutanol, 2-butanol, and diisobutylene (which is a mixture of two isomers of octene). The remaining six fuels were research-grade gasolines of varying formulations.

Abstract Current End-of-Life Vehicle (ELV) recycling processes are mainly based on mechanical separation techniques. These methods are designed to recycle those metals with the highest contribution in the vehicle weight such as steel, aluminum, and copper. However, a conventional vehicle uses around 50 different types of metals, some of them considered critical by the European Commission. The lack of specific recycling processes makes that these metals become downcycled in steel or aluminum or, in the worst case, end in landfills. With the aim to define several ecodesign recommendations from a raw material point of view, it is proposed to apply a thermodynamic methodology based on exergy analysis. This methodology uses an indicator called thermodynamic rarity to assess metal sustainability. It takes into account the quality of mineral commodities used in a vehicle as a function of their relative abundance in Nature and the energy intensity required to extract and process them.

Abstract A torque converter was instrumented with 29 pressure transducers inside five cavities under study (impeller, turbine, stator, clutch cavity between the pressure plate and the turbine shell). A computer model was created to establish correlation with measured torque and pressure. Torque errors between test and simulation were within 5% and K-Factor and torque ratio errors within 2%. Turbulence intensity on the computer model was used to simulate test conditions representing transmission low and high line pressure settings. When turbulence intensity was set to 5%, pressure simulation root mean square errors were within 11%-15% for the high line pressure setting and up to 34% for low line pressure setting. When turbulence intensity was increased to 50% for the low line pressure settings, a 6% reduced root mean square error in the pressure simulations was seen.

Abstract The tire vertical load and inflation pressure have great influence on tire steady- and non-steady-state characteristics and, consequently, on the vehicle handling and stability. The objective of this article is to reveal the coupling effect of tire vertical load and inflation pressure on tire characteristics and then introduce an improved UniTire side force model including such coupling effect through experimental and theoretical analysis. First, the influence of the tire vertical load and inflation pressure on the tire characteristics is presented through experimental analysis. Second, the theoretical tire cornering stiffness and lateral relaxation length model are introduced to study the underlying mechanism of the coupling effect. Then, an improved UniTire side force model including the coupling effect of tire vertical load and inflation pressure is derived. Finally, the proposed improved UniTire side force model is validated through tire steady-state and transient data.

Abstract Diesel engines include systems for cooling, lubrication, and fuel injection and contain a variety of components. A malfunction in any of the engine systems or the presence of any faulty element influences engine performance and deteriorates its components. This research is concerned with the untimely appearance of vital cracks in the liners of a turbocharged heavy-duty Diesel engine. To find the root causes for premature failure, rigorous examinations through visual observations, material characterization, and metallographic investigations are performed. These include Scanning Electron Microscope (SEM) and Energy-Dispersive Spectroscopy (EDS), fracture mechanics analysis, and performance examination, which are also followed by Finite Element Moldings. To find the proper remedy to resolve the problem, drawing a precise and reliable picture of the engine’s operating conditions is required.

Abstract Damage is accumulated by vehicles as they travel. Current damage methods allow for the total accumulated damage to be identified; however, they do not allow for identification of the road segments that induce the largest component of the damage. The objective of this article is to develop a measure, Localized Pseudo Damage (LPD), which defines the amount of damage each individual road excitation contributes to the total accumulated pseudo damage. A novel theoretical development of LPD along with analytical and discrete simulation analyses is presented. The results show that the LPD is causal and correctly identifies the location and magnitude of damaging events. This is further demonstrated with the application of the method on a real road surface.

Abstract Environmental protection and the depletion of nonrenewable energy sources necessitate the search for the replacement of, among others, diesel fuel (Df) in diesel engines with renewable fuel without major structural changes. For this reason, vegetable oils are of interest as a possible fuel for this type of engine. Unfortunately, the physicochemical properties of vegetable oils differ significantly from Df. In addition to the boiling and freezing points, these properties include viscosity, density, and surface tension as well as wetting properties. For this reason, an attempt was made to modify these properties by adding n-hexane (Hex) and ethanol (Et) to canola oil (Co). The viscosity, density, surface tension, and wetting properties of Hex and Et are significantly different from those for Co.

Abstract The frequency of video-capturing collision events from surveillance systems are increasing in reconstruction analyses. The video that has been provided to the investigator may not always include a clear perspective of the relevant area of interest. For example, surveillance video of an incident may have captured a pre- or post-incident perspective that, while failing to capture the precise moment when the pedestrian was struck by a vehicle, still contains valuable information that can be used to assist in reconstructing the incident. When surveillance video is received, a quick and efficient technique to place the subject object or objects into a three-dimensional environment with a known rate of error would add value to the investigation.

Abstract Neutron diffraction is a powerful tool for noninvasive and nondestructive characterization of materials and can be applied even in large devices such as internal combustion engines thanks to neutrons’ exceptional ability to penetrate many materials. While proof-of-concept experiments have shown the ability to measure spatially and temporally resolved lattice strains in a small aluminum engine on a timescale of minutes over a limited spatial region, extending this capability to timescales on the order of a crank angle degree over the full volume of the combustion chamber requires careful design and optimization of the engine structure to minimize attenuation of the incident and diffracted neutrons to maximize count rates.

Abstract To assess the effect of the presence of carbon dioxide (CO2) in natural gases on the knock resistance of fuel, the knock behavior of a lean-burn, high-speed medium Brake Mean Effective Pressure (BMEP) Combined Heat and Power (CHP) engine fueled with CH4 + 8 mole% C3H8 mixtures. The engine experiments are supplemented with ignition measurements and simulations of ignition and cylinder processes for various fuel compositions. The engine results show that increasing the fraction of CO2 results in an increase in knock resistance. The analysis of simulations of cylinder processes shows that for binary mixtures (CH4/CO2) and ternary mixtures (CH4/C3H8/CO2) the increase in knock resistance with increasing CO2 fraction is caused by the reduction in peak pressure/temperature, which consequently increases the autoignition delay time of the mixture.

Abstract Equal-channel angular pressing (ECAP) is among the most applicable severe plastic deformation processes used to fabricate ultrafine-grained materials with superior mechanical properties. In this work, a commercial purity aluminum has been processed via ECAP process up to four passes. The influence of ECAP routes (A and Bc) on the mechanical properties of the material and its grain size was investigated. Microstructural observations of the as-annealed and the rods processed via ECAP were undertaken using optical microscopy. Hardness profiles and contour maps of sections cut perpendicularly and parallel to the load direction were assessed to investigate the effect of ECAP processing on the hardness distribution across the deformed rods. Compressive properties of the rods were also examined. In addition, digital images correlation was used to display the stress distribution along the longitudinal section of the processed sample during the compression test.

Abstract The causes of failure due to cracking in the resistance spot welding of the advanced high-strength steels dual-phase 590 (DP590) were investigated using scanning electron microscopy (SEM), optical microscopy, and the tensile-shear test. The results showed that by increasing the current amount, the formation of the melting zone occurred in the heat-affected zone, leading to the cracking in this area, reducing the tensile strength and decreasing the mechanical properties; the initiation and growth of cracking and failure in this region also happened. In the heat-affected zone, by increasing the current amount with the softening phenomenon, the recrystallized coarse grains also occurred, eventually resulting in the loss of mechanical properties. The results of the tensile-shear test also indicated that by increasing the current up to 12 kA, the strength was raised, but the ductility was reduced.

Abstract This study implements Flame Image Velocimetry (FIV), a diagnostic technique based on post-processing of high-speed soot luminosity images, to show the in-flame flow field development impacted by after-injection in a single-cylinder, small-bore optical diesel engine. Two after-injection cases with different dwell times between the main injection and after-injection, namely, close-coupled and long-dwell, as well as a main-injection-only case are compared regarding flow fields, flow vector magnitude, and turbulence intensity distribution. For each case, high-speed soot luminosity movies from 100 individual combustion cycles are recorded at a high frame rate of 45 kHz for FIV processing. The Reynolds decomposition using a spatial filtering method is applied to the obtained flow vectors so that bulk flow structures and turbulence intensity distributions can be discussed.

Abstract The article considers one of the possible mechanisms of loading the solidity of a cylindrical metal composite high-pressure vessel (MC HPV). This mechanism manifests itself as delamination of a thin-walled metal shell (liner) from a more rigid composite shell causing local buckling. A similar effect can be detected in the manufacturing process of MC HPV, when the composite shell is formed by winding with tension a carbon fiber-reinforced plastic tape on the liner. Pressure transfer from the composite shell to the liner is carried out by the method of temperature analogy, that is, by cooling the composite shell, thermally insulated from the liner. To solve the problem of externally confined liner local buckling an approach is proposed, which is based on three points: the introduction of local technological deviations inherent in actual structures, the determination of the general stress-strain state, and a real-time deforming.

Abstract TOC

Abstract TOC

Abstract TOC