Refine Your Search

Topic

Search Results

Journal Article

Vehicle Stability Control through Optimized Coordination of Active Rear Steering and Differential Driving/Braking

2018-07-05
Abstract In this article, a hierarchical coordinated control algorithm for integrating active rear steering and driving/braking force distribution (ARS+D/BFD) was presented. The upper-level control was synthesized to generate the required rear steering angle and external yaw moment by using a sliding-mode controller. In the lower-level controller, a control allocation algorithm considering driving/braking actuators and tire forces constraints was designed to assign the desired yaw moment to the four wheels. To this end, an optimization problem including several equality and inequality constraints were defined and solved analytically. Finally, computer simulation results suggest that the proposed hierarchical control scheme was able to help to achieve substantial enhancements in handling performance and stability.
Journal Article

U.S. Light-Duty Vehicle Air Conditioning Fuel Use and Impact of Solar/Thermal Control Technologies

2018-12-11
Abstract To reduce fuel consumption and carbon dioxide (CO2) emissions from mobile air conditioning (A/C) systems, “U.S. Light-Duty Vehicle Greenhouse Gas Emissions and Corporate Average Fuel Economy Standards” identified solar/thermal technologies such as solar control glazings, solar reflective paint, and active and passive cabin ventilation in an off-cycle credit menu. National Renewable Energy Laboratory (NREL) researchers developed a sophisticated analysis process to calculate U.S. light-duty A/C fuel use that was used to assess the impact of these technologies, leveraging thermal and vehicle simulation analysis tools developed under previous U.S. Department of Energy projects. Representative U.S. light-duty driving behaviors and weighting factors including time-of-day of travel, trip duration, and time between trips were characterized and integrated into the analysis.
Journal Article

Two-Way Coupled CFD Approach for Predicting Gear Temperature of Oil Jet Lubricated Transmissions

2018-07-24
Abstract This article focuses on the development of a two-way coupled methodology to predict gear temperature of oil jet lubricated transmissions using commercial software for computational fluid dynamics simulation. The proposed methodology applies an overset mesh technique to model the gear interlocking motion, multiphase of air-oil mixture, and heat transfer. Two gear pairs were used to develop and validate the methodology, an overdrive helical gear pair of a commercial vehicle transmission and a standard spur gear pair. Different oil jet lubrication methods were investigated using the proposed methodology, such as oil jet directed at the into-mesh position and at the out-of-mesh position. This investigation showed that out of mesh lubrication direction shows better cooling performance which is in well agreement with previous studies of literature.
Journal Article

Transient Operation and Over-Dilution Mitigation for Low-Pressure EGR Systems in Spark-Ignition Engines

2018-09-17
Abstract Low-Pressure cooled Exhaust Gas Recirculation (LP-cEGR) is proven to be an effective technology for fuel efficiency improvement in turbocharged spark-ignition (SI) engines. Aiming to fully exploit the EGR benefits, new challenges are introduced that require more complex and robust control systems and strategies. One of the most important restrictions of LP-cEGR is the transient response, since long air-EGR flow paths introduce significant transport delays between the EGR valve and the cylinders. High dilution generally increases efficiency, but can lead to cycle-by-cycle combustion variation. Especially in SI engines, higher-than-requested EGR dilution may lead to combustion instabilities and misfires. Considering the long EGR evacuation period, one of the most challenging transient events is throttle tip-out, where the engine operation shifts from a high-load point with high dilution tolerance to a low-load point where EGR tolerance is significantly reduced.
Journal Article

Systematic CFD Parameter Approach to Improve Torque Converter Simulation

2019-04-08
Abstract A systematic parametrization approach was employed to simulate a torque converter operating over a wide range of speed ratios. Results of the simulation yielded torque converter impeller and turbine torques prediction errors below 11% when compared to manufacturer data. Further improvements in the computational fluids dynamic (CFD) model reduced such errors down to 3% for the impeller and 6% for the turbine torque predictions. Convergence was reached well under 300 iterations for the most optimal variable setting, but each speed ratio was let to run for 300 iterations. Solution time for the 300 iterations was 40 minutes per speed ratio. The systematic parametrization provides a very competitive procedure for torque converter simulation with reduced computational error and fast solution time.
Journal Article

Stability Analysis of Combined Braking System of Tractor-Semitrailer Based on Phase-Plane Method

2018-06-04
Abstract An analysis method for the stability of combined braking system of tractor-semitrailer based on phase-plane is investigated. Based on a 9 degree of freedom model, considering longitudinal load transfer, nonlinear model of tire and other factors, the braking stability of tractor-semitrailer is analyzed graphically on the phase plane. The stability of both tractor and semitrailer with different retarder gear is validated with the energy plane, β plane, yaw angle plane and hinged angle plane. The result indicates that in the long downhill with curve condition, both tractor and semitrailer show good stability when retarder is working at 1st and 2nd gear, and when it is at 3rd gear, the tractor is close to be unstable while semitrailer is unstable already. Besides, tractor and semitrailer both lose stability when retarder is working at the 4th gear.
Journal Article

Speed Planning and Prompting System for Commercial Vehicle Based on Real-Time Calculation of Resistance

2019-06-25
Abstract When commercial vehicles drive in a mountainous area, the complex road condition and long slopes cause frequent acceleration and braking, which will use 25% more fuel. And the brake temperature rises rapidly due to continuous braking on the long-distance downslopes, which will make the brake drum fail with the brake temperature exceeding 308°C [1]. Meanwhile, the kinetic energy is wasted during the driving progress on the slopes when the vehicle rolls up and down. Our laboratory built a model that could calculate the distance from the top of the slope, where the driver could release the accelerator pedal. Thus, on the slope, the vehicle uses less fuel when it rolls up and less brakes when down. What we do in this article is use this model in a real vehicle and measure how well it works.
Journal Article

Obstacle Avoidance for Self-Driving Vehicle with Reinforcement Learning

2017-09-23
Abstract Obstacle avoidance is an important function in self-driving vehicle control. When the vehicle move from any arbitrary start positions to any target positions in environment, a proper path must avoid both static obstacles and moving obstacles of arbitrary shape. There are many possible scenarios, manually tackling all possible cases will likely yield a too simplistic policy. In this paper reinforcement learning is applied to the problem to form effective strategies. There are two major challenges that make self-driving vehicle different from other robotic tasks. Firstly, in order to control the vehicle precisely, the action space must be continuous which can’t be dealt with by traditional Q-learning. Secondly, self-driving vehicle must satisfy various constraints including vehicle dynamics constraints and traffic rules constraints. Three contributions are made in this paper.
Journal Article

Methodology for Developing a Diesel Exhaust After Treatment Simulation Tool

2017-09-16
Abstract A methodology for the development of catalyst models is presented. Also, a methodology of the implementation of such models into a modular simulation tool, which simulates the units in succession, is presented. A case study is presented illustrating how suitable models can be found and used for simulations. Such simulations illustrate the behavior of the individual units and the overall system. It is shown how, by simulating the units in succession, the entire after treatment system can be tested and optimized, because the integration makes it possible to observe the effect of the modules on one another.
Journal Article

Investigation of Fatigue Life of Wheels in Commercial Vehicles

2018-08-21
Abstract In India, vehicle population increases every day along with road accidents by 2.5% every year. About 7.7% of accidents are caused by wheel separation, 60% of which are due to nut-related problems. Wheel separations in vehicles occur due to fastener issues and fatigue failures in bolts. A study of the reasons for and mechanisms of nut loosening showed that left-hand side wheels detached and fracture failure occurred in right-hand side studs. Fatigue life of wheels with Nord-Lock washer and without washer is determined by using numerical analysis as per the IS 9438 cornering fatigue test. These numerical results are compared with experimental results.
Journal Article

Integrated Positioning Method for Intelligent Vehicle Based on GPS and UWB

2017-09-23
Abstract Knowledge of intelligent vehicle absolute position is a vital premise for the implementation of decision programming, kinematic and dynamics control. In order to achieve high accuracy positioning and reduce running cost as much as possible under all operating conditions, this paper proposed an integrated positioning method based on GPS and Ultra Wide Band(UWB) for intelligent vehicle’s navigation and position system. In this method, GPS and UWB are alternately active according to the confidence level of GPS signal. When the vehicle is traveling in a wide-open area and GPS signal is well received, the positioning results of Dead Reckoning system are corrected by the low frequency positioning output from GPS. During the correcting process, in order to realize the better fusion of measurement data, a simplified federal Kalman filter was designed by using indirect method.
Journal Article

Influence of Intelligent Active Suspension System Controller Design Techniques on Vehicle Braking Characteristics

2018-12-04
Abstract This article presents a comprehensive investigation for the interaction between vehicle ride vibration control and braking control using two degrees of freedom (2DOF) quarter vehicle model. A typical limited bandwidth active suspension system with nonlinear spring and damping characteristics of practical hydraulic and pneumatic components is controlled to regulate both suspension and tire forces and therefore provide the optimum ride comfort and braking performance of an anti-lock brake system (ABS). In order to design a suitable controller for this nonlinear integrated system, various control techniques are followed including state feedback tuned using Linear Quadratic Regulator (LQR), state feedback tuned using Genetic Algorithm (GA), Proportional Integrated (PI) tuned genetically, and Fuzzy Logic Control (FLC). The ABS control system is designed to limit skid ratio below threshold of 15%.
Journal Article

Improvement in Gear Shift Comfort by Reduction in Double Bump Force of Passenger Vehicles

2017-10-08
Abstract In today’s competitive automobile market, driver comfort is at utmost importance and the bar is being raised continuously. Gear Shifting is a crucial customer touch point. Any issue or inconvenience caused while shifting gear can result into customer dissatisfaction and will impact the brand image. While there are continual efforts being taken by most of the car manufactures, “Double Bump” in gearshift has remained as a pain area and impact severely on the shift feel. This is more prominent in North-South (N-S) transmissions. In this paper ‘Double Bump’ is a focus area and a mathematical / analytical approach is demonstrated by analyzing ‘impacting parameters’ and establishing their co-relation with double bump. Additionally, the results are also verified with a simulation model.
Journal Article

Impact of Dynamic Characteristics of Wheel-Rail Coupling on Rail Corrugation

2019-07-02
Abstract To gain a better understanding of the characteristics of corrugation, including the development and propagation of corrugation, and impact of vehicle and track dynamics, a computational model was established, taking into account the nonlinearity of vehicle-track coupling. The model assumes a fixed train speed of 300 km/h and accounts for vertical interaction force components and rail wear effect. Site measurements were used to validate the numerical model. Computational results show that (1) Wheel polygonalisation corresponding to excitation frequency of 545-572 Hz was mainly attributed to track irregularity and uneven stiffness of under-rail supports, which in turn leads to vibration modes of the bogie and axle system in the frequency range of 500-600 Hz, aggregating wheel wear. (2) The peak response frequency of rail of the non-ballasted track coincides with the excitation frequency of wheel-rail coupling; the resonance results in larger wear amplitude of the rail.
Journal Article

Extending the Magic Formula Tire Model for Large Inflation Pressure Changes by Using Measurement Data from a Corner Module Test Rig

2018-03-05
Abstract Since the tire inflation pressure has a significant influence on safety, comfort and environmental behavior of a vehicle, the choice of the optimal inflation pressure is always a conflict of aims. The development of a highly dynamic Tire Pressure Control System (TPCS) can reduce the conflict of minimal rolling resistance and maximal traction. To study the influence of the tire inflation pressure on longitudinal tire characteristics under laboratory conditions, an experimental sensitivity analysis is performed using a multivalent usable Corner Module Test Rig (CMTR) developed by the Automotive Engineering Group at Technische Universität Ilmenau. The test rig is designed to analyze suspension system and tire characteristics on a roller of the recently installed 4 chassis roller dynamometer. Camber angle, toe angle and wheel load can be adjusted continuously. In addition, it is possible to control the temperature of the test environment between −20 °C and +45 °C.
Journal Article

Explanation for Variability in Lower Frequency Structure-Borne Noise and Vibration: Roles of Rear Subframe Dynamics and Right-Left Spindle Phasing

2018-05-17
Abstract This investigation focuses on a class of rear suspension systems that contain both direct and intersecting structural paths from the tire contact patches to the vehicle body. The structural paths intersect through a dynamically active rear subframe structure. New experiments and computational models are developed and analyzed in this article to investigate the variability of structure-borne noise and vibration due to tire/road interactions in the lower- to mid-frequency regimes. Controlled operational experiments are conducted with a mass-production minivan on a chassis dynamometer equipped with rough road shells. Unlike prior literature, the controlled experiments are analyzed for run-run variations in the structure-borne noise up to 300 Hz in a single vehicle to evaluate the nature of excitations at the spindle as the key source of variation in the absence of significant manufacturing, assembly and instrumentation errors.
Journal Article

Enhanced Low-Order Model with Radiation for Total Temperature Probe Analysis and Design

2018-05-16
Abstract Analysis and design of total temperature probes for accurate measurements in hot, high-speed flows remains a topic of great interest in aerospace propulsion and a number of other engineering areas. One can apply detailed computational methods for simultaneous convection, conduction and radiation heat transfer, but such approaches are not suitable for rapid, routine analysis and design studies. For these studies, there is still a place for low-order approximate methods, and that is the subject of this paper. Here, an enhanced, low-order model is presented that includes conduction with variable thermal conductivity, convection with varying convection coefficient, varying diameter (and thus area) along the length of the sensor and radiation, all implemented in a convenient MATLAB code.
Journal Article

Efficient Component Reductions in a Large-Scale Flexible Multibody Model

2018-03-05
Abstract To make better use of simulations in the automotive driveline design process there is a need for both improved predictive capabilities of typical system models and increased number of variant evaluations carried out during system concept design phase. A previously developed large-scale multibody rotor dynamical powertrain model that combines detailed linear-elastic finite element components and nonlinear joints is used to more accurately simulate system response modes and their variations across the operating-range. However, the total simulation time is too long to include extensive parameter evaluations during the rapid design iterations, which will have a negative influence on the total understanding of the designed system's behaviour. Therefore this paper is about reducing such a large-scale model to one that runs faster, but without losing the ability to predict the most fundamental system characteristics.
Journal Article

Driveline Ratio Selection and Shift Map Optimization for Automatic Transmission Vehicle at Concept Phase through Simulations

2017-10-08
Abstract Traditionally driveline ratios are selected based on trial and error method of proto vehicle testing. This consumes lot of time and increases overall vehicle development effort. Over last few decades, simulation-based design approach has been extensively used to alleviate this problem. This paper describes torque converter and final drive ratio (FDR) selection at concept phase for new Automatic Transmission (AT) vehicle development. Most of the critical data required for simulating vehicle performance and fuel economy (FE) targets were not available (e.g. shift map, clutch slip map, pedal map, dynamic torque, coast down, etc.) at an initial stage of the project. Hence, the risk for assuming right inputs and properly selecting FDR/Torque converter was particularly high. Therefore, a validated AVL Cruise simulation model based on an existing AT vehicle was used as a base for new AT vehicle development to mitigate the risk due to non-availability of inputs.
Journal Article

Development, Testing, and Assessment of a Kinematic Path-Following Model for Towing Vehicle Systems

2019-01-07
Abstract A kinematic path-following model is developed based on an existing modeling framework established by the authors [1, 2] for prediction of the paths of towing vehicle systems. The presented path-following model determines the path of the towing vehicle using the vehicle’s speed and acceleration data collected by an inertial measurement unit (IMU). An Ackerman steering model was presented to calculate instantaneous directional angles and radii for each towed vehicle based on its geometric data and steering angle. In that model the off-tracking effect is properly captured. A 1:4 scale model for a towing vehicle system was built to test the developed steering model, and it was found that the angles and radii of the towing vehicle and each towed unit calculated using the Ackerman steering model agreed very well with those measured from the scale model.
X