Refine Your Search

Topic

Search Results

Journal Article

Wheel Chock Key Design Elements and Geometrical Profile for Truck Vehicle Restraint

2018-06-06
Abstract Wheel chocks are rather simple compliant mechanisms for stabilizing vehicles at rest. However, chocks must be carefully designed given the complex interaction between the chock and the tire/suspension system. Despite their importance for safety, literature is surprisingly limited in terms of what makes a wheel chock efficient. Using simple but reliable quasi-static mechanical models, this study identifies mechanical requirements that help to avoid a number of failure modes associated with many existing wheel chocks. Given that chock grounding is not always possible, a chock’s maximum restraining capacity is only obtained when the wheel is completely supported by the chock. A generic chock profile is proposed to achieve this objective while mitigating undesirable failure modes. The profile is based on fundamental mechanical principles and no assumption is made on the load interaction between the chock and the wheel.
Journal Article

Vehicle Stability Control through Optimized Coordination of Active Rear Steering and Differential Driving/Braking

2018-07-05
Abstract In this article, a hierarchical coordinated control algorithm for integrating active rear steering and driving/braking force distribution (ARS+D/BFD) was presented. The upper-level control was synthesized to generate the required rear steering angle and external yaw moment by using a sliding-mode controller. In the lower-level controller, a control allocation algorithm considering driving/braking actuators and tire forces constraints was designed to assign the desired yaw moment to the four wheels. To this end, an optimization problem including several equality and inequality constraints were defined and solved analytically. Finally, computer simulation results suggest that the proposed hierarchical control scheme was able to help to achieve substantial enhancements in handling performance and stability.
Journal Article

Validation of Crush Energy Calculation Methods for Use in Accident Reconstructions by Finite Element Analysis

2018-10-04
Abstract The crush energy is a key parameter to determine the delta-V in accident reconstructions. Since an accurate car crush profile can be obtained from 3D scanners, this research aims at validating the methods currently used in calculating crush energy from a crush profile. For this validation, a finite element (FE) car model was analyzed using various types of impact conditions to investigate the theory of energy-based accident reconstruction. Two methods exist to calculate the crush energy: the work based on the barrier force and the work based on force calculated by the vehicle acceleration times the vehicle mass. We show that the crush energy calculated from the barrier force was substantially larger than the internal energy calculated from the FE model. Whereas the crush energy calculated from the vehicle acceleration was comparable to the internal energy of the FE model.
Journal Article

U.S. Light-Duty Vehicle Air Conditioning Fuel Use and Impact of Solar/Thermal Control Technologies

2018-12-11
Abstract To reduce fuel consumption and carbon dioxide (CO2) emissions from mobile air conditioning (A/C) systems, “U.S. Light-Duty Vehicle Greenhouse Gas Emissions and Corporate Average Fuel Economy Standards” identified solar/thermal technologies such as solar control glazings, solar reflective paint, and active and passive cabin ventilation in an off-cycle credit menu. National Renewable Energy Laboratory (NREL) researchers developed a sophisticated analysis process to calculate U.S. light-duty A/C fuel use that was used to assess the impact of these technologies, leveraging thermal and vehicle simulation analysis tools developed under previous U.S. Department of Energy projects. Representative U.S. light-duty driving behaviors and weighting factors including time-of-day of travel, trip duration, and time between trips were characterized and integrated into the analysis.
Journal Article

Two-Way Coupled CFD Approach for Predicting Gear Temperature of Oil Jet Lubricated Transmissions

2018-07-24
Abstract This article focuses on the development of a two-way coupled methodology to predict gear temperature of oil jet lubricated transmissions using commercial software for computational fluid dynamics simulation. The proposed methodology applies an overset mesh technique to model the gear interlocking motion, multiphase of air-oil mixture, and heat transfer. Two gear pairs were used to develop and validate the methodology, an overdrive helical gear pair of a commercial vehicle transmission and a standard spur gear pair. Different oil jet lubrication methods were investigated using the proposed methodology, such as oil jet directed at the into-mesh position and at the out-of-mesh position. This investigation showed that out of mesh lubrication direction shows better cooling performance which is in well agreement with previous studies of literature.
Journal Article

Transient Operation and Over-Dilution Mitigation for Low-Pressure EGR Systems in Spark-Ignition Engines

2018-09-17
Abstract Low-Pressure cooled Exhaust Gas Recirculation (LP-cEGR) is proven to be an effective technology for fuel efficiency improvement in turbocharged spark-ignition (SI) engines. Aiming to fully exploit the EGR benefits, new challenges are introduced that require more complex and robust control systems and strategies. One of the most important restrictions of LP-cEGR is the transient response, since long air-EGR flow paths introduce significant transport delays between the EGR valve and the cylinders. High dilution generally increases efficiency, but can lead to cycle-by-cycle combustion variation. Especially in SI engines, higher-than-requested EGR dilution may lead to combustion instabilities and misfires. Considering the long EGR evacuation period, one of the most challenging transient events is throttle tip-out, where the engine operation shifts from a high-load point with high dilution tolerance to a low-load point where EGR tolerance is significantly reduced.
Journal Article

Torque and Pressure CFD Correlation of a Torque Converter

2019-08-22
Abstract A torque converter was instrumented with 29 pressure transducers inside five cavities under study (impeller, turbine, stator, clutch cavity between the pressure plate and the turbine shell). A computer model was created to establish correlation with measured torque and pressure. Torque errors between test and simulation were within 5% and K-Factor and torque ratio errors within 2%. Turbulence intensity on the computer model was used to simulate test conditions representing transmission low and high line pressure settings. When turbulence intensity was set to 5%, pressure simulation root mean square errors were within 11%-15% for the high line pressure setting and up to 34% for low line pressure setting. When turbulence intensity was increased to 50% for the low line pressure settings, a 6% reduced root mean square error in the pressure simulations was seen.
Journal Article

Tire Side Force Characteristics with the Coupling Effect of Vertical Load and Inflation Pressure

2018-11-09
Abstract The tire vertical load and inflation pressure have great influence on tire steady- and non-steady-state characteristics and, consequently, on the vehicle handling and stability. The objective of this article is to reveal the coupling effect of tire vertical load and inflation pressure on tire characteristics and then introduce an improved UniTire side force model including such coupling effect through experimental and theoretical analysis. First, the influence of the tire vertical load and inflation pressure on the tire characteristics is presented through experimental analysis. Second, the theoretical tire cornering stiffness and lateral relaxation length model are introduced to study the underlying mechanism of the coupling effect. Then, an improved UniTire side force model including the coupling effect of tire vertical load and inflation pressure is derived. Finally, the proposed improved UniTire side force model is validated through tire steady-state and transient data.
Journal Article

Theory of Collision Avoidance Capability in Automated Driving Technologies

2018-10-29
Abstract To evaluate that automated vehicle is as safe as a human driver, a following question is studied: how does an automated vehicle react under extreme conditions close to collision? In order to understand the collision avoidance capability of an automated vehicle, we should analyze not only such post-extreme condition behavior but also pre-extreme condition behavior. We present a theory to analyze the collision avoidance capability of automated driving technologies. We also formulate a collision avoidance equation on the theory. The equation has two types of solutions: response driving plans and preparation driving plans. The response driving plans are supported by response strategy on which the vehicle reacts after detection of a hazard and they are highly efficient in terms of travel time.
Journal Article

Theoretical Study of Improving the Safety of the “Operator, Machine, and Environment” System when Performing Transport Operations

2018-06-05
Abstract The article considers the issues of a systemic approach to studying safety levels in transport operations and ways to increase the safety of the operator-machine system in Russian transport. The principal and problematic issues of reducing the risk of injury by preventing traffic accidents and reducing the severity of their impact have not been sufficiently addressed. When performing transport operations, there are often disagreements between the elements of the “Operator, Machine, and Environment” technological system due to the influence of external conditions and parameters of the constantly-changing environment in the workplace. This leads to a sharp increase in the number of failures of system elements, which reduces the level of safety of transport operations.
Journal Article

The Placement of Digitized Objects in a Point Cloud as a Photogrammetric Technique

2018-08-08
Abstract The frequency of video-capturing collision events from surveillance systems are increasing in reconstruction analyses. The video that has been provided to the investigator may not always include a clear perspective of the relevant area of interest. For example, surveillance video of an incident may have captured a pre- or post-incident perspective that, while failing to capture the precise moment when the pedestrian was struck by a vehicle, still contains valuable information that can be used to assist in reconstructing the incident. When surveillance video is received, a quick and efficient technique to place the subject object or objects into a three-dimensional environment with a known rate of error would add value to the investigation.
Journal Article

Systematic CFD Parameter Approach to Improve Torque Converter Simulation

2019-04-08
Abstract A systematic parametrization approach was employed to simulate a torque converter operating over a wide range of speed ratios. Results of the simulation yielded torque converter impeller and turbine torques prediction errors below 11% when compared to manufacturer data. Further improvements in the computational fluids dynamic (CFD) model reduced such errors down to 3% for the impeller and 6% for the turbine torque predictions. Convergence was reached well under 300 iterations for the most optimal variable setting, but each speed ratio was let to run for 300 iterations. Solution time for the 300 iterations was 40 minutes per speed ratio. The systematic parametrization provides a very competitive procedure for torque converter simulation with reduced computational error and fast solution time.
Journal Article

Study of a Mono-Tube Hydraulic Energy Harvesting Shock Absorber

2019-09-23
Abstract In this chapter, a mono-tube hydraulic energy harvesting shock absorber is proposed. The absorber is featured with the autogeneration where it permits harvesting waste energy with a proper asymmetric ratio of compression/extension damping force can be obtained. Using the continuity equation and including the compressibility of the oil, equations that describe the variation of the oil pressure in model chambers are derived. Then, relations that relate chambers’ pressure with the damping force, the harvested power, and the system efficiency are derived. Results illustrate the effects of frequency, amplitude, external resistance, and chambers’ size on the damping force and the harvested power. The proposed model can harvest an average power of 500 W with maximum peak of 1800 W using an external resistance of 10 Ω at an input amplitude of 50 mm and frequency of 1.67 Hz.
Journal Article

Studies on Friction Mechanism of NAO Brake-Pads Containing Potassium Titanate Powder as a Theme Ingredient

2017-09-17
Abstract Potassium titanate (KT) fibers/whiskers are used as a functional filler for partial replacement of asbestos in NAO friction materials (FMs). Based on little information reported in open literature; its exact role is not well defined since some papers claim it as the booster for resistance to fade (FR), or wear (WR) and sometimes as damper for friction fluctuations. Interestingly, KT fibers and whiskers (but not powder) are proved as carcinogens by the International Agency for Research on Cancer (IARC). However, hardly any efforts are reported on exploration of influence of KT powder and its optimum amount in NAO FMs (realistic composites) in the literature. Hence a series of five realistic multi-ingredient compositions in the form of brake-pads with similar parent composition but varying in the content of KT powder from 0 to 15 wt% (in the steps of 3) were developed. These composites were characterized for physical, mechanical, chemical and tribological performance.
Journal Article

Structural Optimization of a Pickup Frame Combining Thickness, Shape and Feature Parameters for Lightweighting

2018-08-08
Abstract The methods for improving the torsion stiffness of a pickup chassis frame were discussed, including increasing the part thickness on frame, enlarging the cross section of rails, and adding bulkhead feature inside the rails. Sizing optimization was conducted to get the optimal thickness configuration for frame parts and meet the siffness requirement. The cross section of frame rails were parameterized and shape optimization was conduted to get the optimal rail cross sections for stiffness improvement. Additional bulkheads were added to the frame rails, and sizing optimization conducted to find the most effective bulkheads to add and their optimal gauge. A material efficiency ratio μ is used to evaluate the efficiency of a design change with respect to torsion stiffness. Among those torsion improvement methods, adding bulkhead feature gives the highest material efficiency ratio, but the stiffness improvement range is very limited.
Journal Article

Stability Analysis of Combined Braking System of Tractor-Semitrailer Based on Phase-Plane Method

2018-06-04
Abstract An analysis method for the stability of combined braking system of tractor-semitrailer based on phase-plane is investigated. Based on a 9 degree of freedom model, considering longitudinal load transfer, nonlinear model of tire and other factors, the braking stability of tractor-semitrailer is analyzed graphically on the phase plane. The stability of both tractor and semitrailer with different retarder gear is validated with the energy plane, β plane, yaw angle plane and hinged angle plane. The result indicates that in the long downhill with curve condition, both tractor and semitrailer show good stability when retarder is working at 1st and 2nd gear, and when it is at 3rd gear, the tractor is close to be unstable while semitrailer is unstable already. Besides, tractor and semitrailer both lose stability when retarder is working at the 4th gear.
Journal Article

Speed Planning and Prompting System for Commercial Vehicle Based on Real-Time Calculation of Resistance

2019-06-25
Abstract When commercial vehicles drive in a mountainous area, the complex road condition and long slopes cause frequent acceleration and braking, which will use 25% more fuel. And the brake temperature rises rapidly due to continuous braking on the long-distance downslopes, which will make the brake drum fail with the brake temperature exceeding 308°C [1]. Meanwhile, the kinetic energy is wasted during the driving progress on the slopes when the vehicle rolls up and down. Our laboratory built a model that could calculate the distance from the top of the slope, where the driver could release the accelerator pedal. Thus, on the slope, the vehicle uses less fuel when it rolls up and less brakes when down. What we do in this article is use this model in a real vehicle and measure how well it works.
Journal Article

Robust Design for Steering Mechanism Based on Preference Function

2018-03-01
Abstract In order to improve robustness of vehicle dynamic performance, a steering mechanism model is proposed with alignment parameters of front wheel based on preference function method. In the steering mechanism model controllable variables include the trapezoid connection length, the base angle of steering trapezoid, the kingpin inclination angle, caster, camber and uncontrollable variables include load and initial braking velocity. Optimization objective is some vehicle dynamic performance. In the preference function method the individual performance preference and preference aggregation in designing variable space and performance variable space are analyzed. The individual performance preference includes the controllable variable preference, noise factor preference and optimization objective preference. The aggregation function is developed by aggregating all the individual performance preferences.
Journal Article

Prediction and Control of Response Time of the Semitrailer Air Braking System

2019-05-09
Abstract The response time of the air braking system is the main parameter affecting the longitudinal braking distance of vehicles. In this article, in order to predict and control the response time of the braking system of semitrailers, an AMESim model of the semitrailer braking system involving the relay emergency valve (REV) and chambers was established on the basis of analyzing systematically the working characteristics of the braking system in different braking stages: feedback braking, relay braking, and emergency braking. A semitrailer braking test bench including the brake test circuit and data acquisition system was built to verify the model with typical maneuver. For further evaluating the semitrailer braking response time, an experiment under different control pressures was carried out. Experimental results revealed the necessity of controlling the response time.
Journal Article

Personalized Controller Design for Electric Power Steering System Based on Driver Behavior

2017-09-23
Abstract Electric power steering (EPS) system is a kind of dynamic control system for vehicle steering, which can amplify the driver steering torque inputs to the vehicle to improve steering comfortable and performance, but the present EPS can’t cater to the driving habits of different people. In this paper, a personalized EPS controller is designed based on the driver behavior, which combines real-time driver behavior identification strategy with personalized assistance characteristic. Firstly, the driver behavior data acquisition system is designed and established, based on which, the input data of different kinds of drivers along with vehicle signals are collected under typical working conditions, then the identification of driver behavior online is realized using the BP neural network.
X