Search Results

The main assignment of Controlled Auto Ignition (CAI) operation range expansion is to reduce the burn rate or combustion noise at high load and to minimize misfire at low load. The potential of two principal EGR strategies is well known to initiate CAI in a wide range of operation map by using a variable train system: the Exhaust Port Recirculation (EPR) for higher part load and the Combustion Chamber Recirculation (CCR - also called Negative Valve Overlap) for lower part load. However the detailed comparison of the ignition phenomena with each EGR strategy has not been fully studied yet. In this paper, EPR and CCR were compared with same operational condition (engine speed and load). For the analysis, flame luminescence and Raman scattering method for optical measurement and STAR-CD (CD-adapco) for numerical simulation are used.

During a thermal regeneration of a Diesel particulate filter (DPF) the temperature inside the DPF may raise above critical thresholds in an uncontrolled way (thermal shock). Especially driving conditions with a comparable low exhaust gas mass flow and high oxygen content like idle speed may create a thermal shock. This paper presents a concept for an ECU software structure to prevent the DPF from reaching improper temperatures and the methodology in order to calibrate this ECU structure. The concept deals in general with a closed-loop control of the exhaust gas air-fuel-ratio during the critical engine operation phases. Those critical operation phases are identified at the engine test bench during “Drop-to-Idle” and “Drop-to-Overrun” experiments. The experiments show that those phases are critical having on the one hand a low exhaust gas mass flow and on the other hand a high oxygen percentage in the exhaust gas.

Future Diesel engines must meet extended requirements regarding air-fuel ratio, exhaust gas recirculation (EGR) capability, and tailored exhaust gas temperatures in the complete engine map to comply with the future pollutant emission standards. In this respect, parallel turbines combined with two separate exhaust manifolds have the potential to increase the exhaust gas temperature upstream of the exhaust aftertreatment system and reduce the catalyst light-off time. Furthermore, variable exhaust valve (EV) lifts enable new control strategies of the boosting system without additional actuators. Therefore, hardware robustness can be improved. This article focuses on the parallel-sequential boosting concept (PSBC) for a high-performance four-cylinder Diesel engine with separated exhaust manifolds combined with EV deactivation. One EV per cylinder is connected to one of the separated exhaust manifolds and, thus, connected to one of the turbines.

So far, the effect of injection rate shaping on the diesel combustion in small-bore DI diesel engines has not been extensively investigated, especially at high part load conditions with high EGR rates. The benefit of injection rate shaping is already verified for heavy duty engines at high load conditions with and without EGR. For this investigation, single cylinder engine investigations were conducted at the VKA / RWTH Aachen University. In order to meet the future NOx legislation limits like US-Tier2Bin5 it is crucial to reduce NOx especially at the high load points of the certification cycles, as FTP75 or US06. For the single cylinder investigations two part load points were chosen, which have relevance for the mentioned certification cycles. The experimental work focuses on different rate shapes as rectangular (Common-Rail type), ramp and boot shape at high EGR rates.

Homogeneous charge compression ignition (HCCI) is a part load, low-temperature combustion process which operates at lean mixtures and produces ultra-low NOX emissions. As opposed to SI engines that use a spark to control combustion timing, HCCI combustion is enabled by compression induced autoignition which is characterized by rapid global and spatial combustion yielding fuel efficiency benefits. This process is highly dependent on the in-cylinder state, including pressure, temperature and trapped mass. The absence of a direct combustion control proves to be a major challenge and results in unstable engine operation especially at the limits of the narrow operation range. In recent studies, direct water injection is used in HCCI combustion to stabilize combustion and increase the operation range. This paper outlines the thermodynamic influence and evaluation of the potential of water injection for HCCI combustion.

The future worldwide emission regulations will request a drastic decrease of Diesel engine tailpipe emissions. Depending on the planned application and the real official regulations, a further strong decrease of engine out emissions is necessary, even though the utilized exhaust after-treatment systems are very powerful. To reduce NOx emissions internally, the external exhaust gas recirculation (EGR) is known as the most effective way. Due to the continuously increasing requirements regarding specific power, dynamic behavior and low emissions, future air path systems have to fulfill higher requirements and, consequently, become more and more complex, e.g. arrangements with a 2-stage turbo charging or 2-stage EGR system with different stages of cooling performance.

Due to experimental challenges, combustion of diesel-like jets has rarely been characterized by laser-based quantitative multiscalar measurements. In this work, recently developed laser diagnostics for combustion temperature and the concentrations of CO, O2, and NO are applied to a diesel-like jet, using a highly oxygenated fuel. The diagnostic is based on spontaneous Raman scattering (SRS) and laser-induced fluorescence (LIF) methods. Line imaging yields multiscalar profiles across the jet cross section. Measurements turn out to be particularly accurate, because near-stoichiometric combustion occurs in the central region of the jet. Thereby, experimental cross-influences by light attenuation and interfering emissions are greatly reduced compared to the combustion of conventional, sooting diesel fuel jets. This is achieved by fuel oxygenation and enhanced premixing.

For gasoline engines controlled autoignition provides the vision of enabling the fuel consumption benefit of stratified lean combustion systems without the drawback of additional NOx aftertreatment. In this study the potential of certain biofuels on this combustion system was assessed by single-cylinder engine investigations using the exhaust strategy "combustion chamber recirculation" (CCR). For the engine testing sweeps in the internal EGR rate with different injection strategies as well as load sweeps were performed. Of particular interest was to reveal fuel differences in the achievable maximal load as well as in the NOx emission behavior. Additionally, experiments with a shock tube and a rapid compression machine were conducted in order to determine the ignition delay times of the tested biofuels concerning controlled autoignition-relevant conditions.