Refine Your Search

Search Results

Standard

Wide Base Disc Wheels and Demountable Rims

2007-04-30
J876_200704
This SAE Recommended Practice establishes uniform engineering nomenclature for wide base disc wheels and demountable rims. This nomenclature and accompanying figures are intended to define fundamental wide base disc wheels and demountable rim terms. The dimensions given are those necessary to maintain serviceability and interchangeability of the wide base disc wheels and demountable rims with standard hardware. Valve clearances have not been included in this document.
Standard

Wheels/Rims - Military Vehicles Test Procedures and Performance Requirements

2019-06-06
J1992_201906
This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of disc wheels, demountable rims, and bolt-together divided wheels intended for normal highway use on military trucks, buses, truck-trailers, and multipurpose vehicles. For other (non-military) wheels and rims intended for normal highway use on trucks and buses, refer to SAE J267. For wheels intended for normal highway and temporary use on passenger cars, light trucks, and multipurpose vehicles, refer to SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, refer to SAE J1204. This document does not cover off-highway or other special application wheels and rims.
Standard

Wheels/Rims - Military Vehicles - Test Procedures and Performance Requirements

2012-04-23
J1992_201204
This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of disc wheels, demountable rims, and bolt-together divided wheels intended for normal highway use on military trucks, buses, truck-trailers, and multipurpose vehicles. For wheels and rims intended for normal highway use on trucks and buses, see SAE J267. For wheels intended for normal highway use on passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. This document does not cover off-highway or other special application wheels and rims.
Standard

Wheel End Assembly and Axle Spindle Interface Dimensions—Truck and Bus

2008-08-22
J2475_200808
This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, seal and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, U, W, R, N and P.
Standard

Wheel End Assembly and Axle Spindle Interface Dimensions--Truck and Bus

2018-05-02
WIP
J2475

This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, seal and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, N, P, R, U, and W.

Standard

Wheel End Assembly and Axle Spindle Interface Dimensions - Truck and Bus

2014-07-30
J2475_201407
This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, seal and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, N, P, R, U, and W.
Standard

Setting Preload in Heavy-Duty Wheel Bearings

2019-10-07
J2535_201910
This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a “N” trailer axle b “R” powered rear axle c “FF / FG” nonpowered front axle d “P” trailer axle This document applies to on-highway applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.
Standard

Setting Preload in Heavy-Duty Wheel Bearings

2013-02-11
J2535_201302
This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a “N” trailer axle b “R” powered rear axle c “FF / FG” nonpowered front axle d “P” trailer axle This document applies to on-highway applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.
Standard

Outboard Mounted Brake Drum/Disc Wheel Hub Interface Dimensions - Truck and Bus

2019-10-17
J1671_201910
This recommended practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. This recommended practice is intended for outboard mounted brake drums and disc wheel hubs commonly used on class 7 and 8 commercial vehicles. Included are SAE J694 mounting systems II, III, IV, XIV, and X. Special and less common applications are not covered.
Standard

Outboard Mounted Brake Drum/Disc Wheel Hub Interface Dimensions - Truck and Bus

2015-02-20
J1671_201502
This recommended practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. This recommended practice is intended for outboard mounted brake drums and disc wheel hubs commonly used on class 7 and 8 commercial vehicles. Included are SAE J694 mounting systems II, III, IV, XIV, and X. Special and less common applications are not covered.
Standard

Nomenclature - Wheels, Hubs, and Rims for Commercial Vehicles

2017-10-23
J393_201710
This SAE Recommended Practice establishes uniform engineering nomenclature for wheels, hubs, rims, and their components used in truck, bus, and trailer applications. This nomenclature and accompanying drawings are intended to define functional truck wheel, hub, and rim designs. For nomenclature specific to “passenger-type” disc wheels, refer to SAE J1982. The International Standard (ISO) nomenclature is shown in parentheses when different than SAE J393.
Standard

Inboard Mounted Disc Brake Rotor/Disc Wheel Hub Interface Dimensions - Commercial Vehicles

2012-05-29
J2696_201205
This SAE Recommended Practice establishes dimensions and tolerances for the interface between inboard mounted disc brake rotors and disc wheel hubs. The geometric features described in this document are shown at true position. This document is intended for inboard mounted disc brake rotors and disc wheel hubs for Class 5, 6, 7, and 8 commercial vehicles. Special and less common applications are not covered.
Standard

Identification of Truck, Trailer, and Bus Wheel Seals and Associated Packaging

2002-05-31
J2224_200205
This SAE Information Report lists the symbols used by suppliers of truck, trailer, and bus wheel seals to identify their products. These symbols appear on seals and packaging. The purpose of this document is to provide users of truck, trailer, and bus wheel seals a means of identifying the suppliers of all such components by use of the symbology utilized by the suppliers on their components and packaging.
Standard

Identification of Truck, Trailer, and Bus Wheel Seals and Associated Packaging

2015-11-19
J2224_201511
This SAE Information Report lists the symbols used by suppliers of truck, trailer, and bus wheel seals to identify their products. These symbols appear on seals and packaging. 1.1 Purpose The purpose of this document is to provide users of truck, trailer, and bus wheel seals a means of identifying the suppliers of all such components by use of the symbology utilized by the suppliers on their components and packaging.
Standard

Identification of Truck, Trailer, and Bus Wheel Seals and Associated Packaging

1994-10-01
J2224_199410
This SAE Information Report lists the symbols used by suppliers of truck, trailer, and bus wheel seals to identify their products. These symbols appear on seals and packaging. The purpose of this document is to provide users of truck, trailer, and bus wheel seals a means of identifying the suppliers of all such components by use of the symbology utilized by the suppliers on their components and packaging.
X