Refine Your Search

Date

Date

Topic

Topic

Manufacturing processes Ground support Technical review Maintenance and Aftermarket Metallurgy Wheel wells Parts Aerospace A-5A Wheels, Brakes and Skid Controls Committee

Search Results

Viewing 1 to 20 of 57
123Next >Last >>
Sort by title
Standard

Wheel and Brake (Sand and Permanent Mold) Castings - Minimum Requirements for Aircraft Applications
2005-01-05
HISTORICAL
AS586B
This SAE Aerospace Standard (AS) sets forth the minimum quality required for aircraft wheel and brake castings. Its use will establish minimum acceptable requirements for internal structure and surface conditions and is predicated on the use of a casting factor for the ultimate load of more than 1.51 through 2.00. When casting factors of 1.25 through 1.50 are used, visual, penetrant, and radiographic or other approved equivalent nondestructive inspection methods shall all be required on each production casting. Where specific parts, or areas of parts, require a quality level exceeding that described by this document, the requirements shall be established by negotiation between the purchaser and vendor.
Standard

Wheel and Brake (Sand and Permanent Mold) Castings - Minimum Requirements for Aircraft Applications
2002-07-30
HISTORICAL
AS586A
This SAE Aerospace Standard (AS) sets forth the minimum quality required for aircraft wheel and brake castings. Its use will establish minimum acceptable requirements for internal structure and surface conditions and is predicated on the use of a casting factor for the ultimate load of more than 1.51 through 2.00. When casting factors of 1.25 through 1.50 are used, visual, penetrant, and radiographic or other approved equivalent nondestructive inspection methods shall all be required on each production casting. Where specific parts, or areas of parts, require a quality level exceeding that described by this document, the requirements shall be established by negotiation between the purchaser and vendor.
Standard

Wheel and Brake (Sand and Permanent Mold) Castings - Minimum Requirements for Aircraft Applications
2011-01-06
CURRENT
AS586C
This SAE Aerospace Standard (AS) sets forth the minimum quality required for aircraft wheel and brake castings. Its use will establish minimum acceptable requirements for internal structure and surface conditions and is predicated on the use of a casting factor for the ultimate load of more than 1.51 through 2.00. When casting factors of 1.25 through 1.50 are used, visual, penetrant, and radiographic or other approved equivalent nondestructive inspection methods shall all be required on each production casting. Where specific parts, or areas of parts, require a quality level exceeding that described by this document, the requirements shall be established by negotiation between the purchaser and vendor.
Standard

WHEEL AND BRAKE (SAND AND PERMANENT MOLD) CASTINGS — MINIMUM REQUIREMENTS FOR AIRCRAFT APPLICATIONS
1965-01-20
HISTORICAL
AS586
This standard sets forth the minimum quality required for aircraft wheel and brake castings. Its use will establish minimum acceptable requirements for internal structure and surface conditions and is predicated on the use of a casting factor for the ultimate load of 1.51 (minimum) to 2.00 (maximum). When casting factors of 1.25 minimum to 1.50 maximum are used, visual, penetrant, and radiographic or other approved equivalent non-destructive inspection methods shall all be required on each production casting. Where specific parts or areas require a quality level exceeding that described by this standard, the requirements shall be established by negotiation between the purchaser and vendor.
Standard

Valve, Inflation, Aircraft Wheel
2019-11-14
CURRENT
AS6817
This SAE Aerospace Standard (AS) defines the configuration of aircraft wheel inflation valve assemblies, including required tolerances, materials, and appropriate finishes.
Standard

Use of Structural Carbon Heat Sink Brakes on Aircraft
2016-11-15
CURRENT
AIR1934A
The purpose of this document is to relate areas where carbon brake technology may differ from traditional steel brake technology in design and performance. Carbon brakes have been used on military aircraft for many years and are now frequently used on newly commercial developed aircraft. This document presents some of the lessons learned.
Standard

USAF Aircraft Wheels
2012-05-09
HISTORICAL
AIR4012B
This SAE Aerospace Information Report (AIR) documents general technical data associated with many of the wheels used in the Air Force.
Standard

USAF Aircraft Wheels
2012-07-19
CURRENT
AIR4012C
This SAE Aerospace Information Report (AIR) documents general technical data associated with many of the wheels used in the Air Force.
Standard

Thermal Sensitive Inflation Pressure Release Devices for Tubeless Aircraft Wheels
2012-05-09
HISTORICAL
AS707B
This standard establishes minimum design, installation, qualification, and operational requirements for thermally actuated, pressure release devices for use only in tubeless tire type aircraft wheels. These devices are designed to completely release the contained inflation pressure from a tubeless tire and wheel assembly when brake generated heat causes the assembly to exceed a safe temperature operating level. The objective is to prevent tire or wheel rupture due to brake generated heat which could cause serious personnel injuries or serious aircraft operational hazards.
Standard

Test Method for Catalytic Carbon Brake Disk Oxidation
2013-12-04
WIP
AS6289
The scope of the test method is to provide stakeholders including fluid manufacturers, brake manufacturers, aircraft constructors, aircraft operators and airworthiness authorities with a relative assessment of the effect of deicing chemicals on carbon oxidation. This test is designed to assess the relative effects of runway deicing chemicals by measuring mass change of contaminated and bare carbon samples tested under the same conditions.
Standard

Test Method for Catalytic Carbon Brake Disk Oxidation
2013-03-11
WIP
AIR5567B
The scope of the test method is to provide stakeholders including fluid manufacturers, brake manufacturers, aircraft constructors, aircraft operators and airworthiness authorities with a relative assessment of the effect of deicing chemicals on carbon oxidation. This simple test is only designed to assess the relative effects of runway deicing chemicals by measuring mass change of contaminated and bare carbon samples tested under the same conditions. It is not possible to set a general acceptance threshold oxidation limit based on this test method because carbon brake stack oxidation is a function of heat sink design and the operating envirnoment.
Standard

Test Method for Catalytic Carbon Brake Disk Oxidation
2009-05-13
HISTORICAL
AIR5567
The scope of the test method is to provide stakeholders including fluid manufacturers, brake manufacturers, aircraft constructors, aircraft operators and airworthiness authorities with a relative assessment of the effect of deicing chemicals on carbon oxidation. This simple test is only designed to assess the relative effects of runway deicing chemicals by measuring mass change of contaminated and bare carbon samples tested under the same conditions. It is not possible to set a general acceptance threshold oxidation limit based on this test method because carbon brake stack oxidation is a function of heat sink design and the operating envirnoment.
Standard

THERMAL SENSITIVE PRESSURE RELEASE DEVICES FOR TUBELESS AIRCRAFT WHEELS
1982-04-01
HISTORICAL
AS707A
This standard establishes minimum design, installation, qualification, and operational requirements for thermally actuated, pressure release devices for use only in tubeless tire type aircraft wheels. These devices are designed to completely release the contained air pressure from a tubeless tire and wheel assembly when absorbed and/or brake generated heat causes the tire or wheel to exceed a safe pressure/temperature/load operating level. The objective is to prevent tire or wheel rupture from brake generated heat which could cause serious personnel injuries or serious aircraft operational hazards.
Standard

THERMAL SENSITIVE INFLATION PRESSURE RELEASE DEVICES FOR TUBELESS AIRCRAFT WHEELS
1988-12-01
HISTORICAL
AS707
This standard establishes minimum design, installation, qualification, and operational requirements for thermally actuated, pressure release devices for use only in tubeless tire type aircraft wheels. These devices are designed to completely release the contained inflation pressure from a tubeless tire and wheel assembly when brake generated heat causes the assembly to exceed a safe temperature operating level. The objective is to prevent tire or wheel rupture due to brake generated heat which could cause serious personnel injuries or serious aircraft operational hazards.
Standard

Skid Control Equipment
2007-12-12
HISTORICAL
AS483B
This standard covers minimum requirements for skid control equipment for use on all types and models of civil aircraft. It shall be the responsibility of the applicant to determine the compatibility of these requirements with the application aircraft and to specify requirements in excess of these minimums as necessary.
Standard

SKID CONTROL SYSTEM VIBRATION SURVEY
2008-06-16
HISTORICAL
AIR764C
This technical report documents three surveys to determine realistic vibration requirements for skid control systems specifications and obtain updated vibration information for locations in aircraft where skid control system components are mounted.
123Next >Last >>
X