Standard
Wrenching Configuration, 12 Spline, For Metric Threaded Fasteners
2012-11-19
HISTORICAL
MA1549
Search Results
Standard
Wrenching Configuration, 12 Lobed, For Threaded Fasteners
2006-10-10
HISTORICAL
AS1159B
Standard
Wrench Configuration, 12 Lobed Drive
2012-11-01
HISTORICAL
AS1325
Standard
White Paper to Support Supersession of MIL-S-8879C With AS8879C
2018-08-23
HISTORICAL
AIR5926
This paper was prepared to support supersession of MIL-S-8879C with Screw Thread Conformity Task Force selected industry standard AS8879C, published by the Society of Automotive Engineers (SAE). Other documentation changes will be covered by separate papers. Separate papers are anticipated for thread gaging issues, and thread gage calibration procedures. The STC-TF decided that the thread design standard needed to be completed before thread gage definition could be addressed. Thread gage definition has to be known before calibration procedures can be addressed.
Standard
Water Compatibility of Aircraft Greases
1995-05-01
CURRENT
AIR39
Standard
WRENCHING ELEMENT, SPLINE DRIVE - DIMENSIONS FOR
2012-11-19
HISTORICAL
AS5443A
Standard
WRENCHING CONFIGURATION, BI-HEXAGONAL (12 POINT) DRIVE, DESIGN STANDARD FOR
2006-05-02
HISTORICAL
AS870D
Standard
WASHER-KEY, CUP LOCK, AMS5510, METRIC
2012-12-10
HISTORICAL
MA3441
Standard
WASHER, KEY - 90° LOCKING, CRES, UNS S32100, METRIC
2012-12-10
HISTORICAL
MA4037A
Standard
WASHER, KEY - 180° LOCKING, CRES, UNS S32100, METRIC
2012-12-10
HISTORICAL
MA4038B
Standard
WASHER, FLAT, COUNTERSUNK UNS S66286
2006-05-05
HISTORICAL
AS3565
Standard
WASHER, FLAT – AMS5510
2012-11-01
HISTORICAL
AS9549
Standard
WASHER, CUP, LOCK – CRES AMS5510
2012-11-01
HISTORICAL
AS9880
Standard
Undercuts for Straight Screw Threads - Metric
2019-06-19
CURRENT
AS1508A
This standard provides recommended dimensional data for screw thread undercuts for straight 'MJ' metric screw threads in accordance with AS1370.
Standard
Undercuts for Straight Screw Threads - Metric
2012-11-01
HISTORICAL
AS1508
This standard provides recommended dimensional data for screw thread undercuts for straight ‘MJ’ metric screw threads in accordance with AS1370.
Standard
Undercuts for Straight Screw Threads - Metric
2018-08-23
HISTORICAL
MA1508
This SAE Aerospace Standard (MA) provides recommended dimensional data for screw thread undercuts for straight “MJ” metric screw threads in accordance with MA1370.
Standard
Threaded Fastener Protrusion Through Self-Locking Nuts
2018-01-10
CURRENT
ARP1515B
The external threaded fastener protrusion shall be defined as the external threads including the chamfer which extend through the top surface of the nut, see Figure 1.
Standard
Threaded Fastener Protrusion Through Self-Locking Nuts
2012-11-02
HISTORICAL
ARP1515A
The external threaded fastener protrusion shall be defined as the external threads including the chamfer which extend through the top surface of the nut, see Figure 1.
Standard
Thread Inspection Practices
2020-02-03
CURRENT
AS5870
This document addresses AS8879 thread inspection issues relating to selection, usage and capability of gages. It addresses the selection of calibrated measurement gages, the need for defined quality metrics, the methodology of determining the appropriate guardband factors, and the minimum inspection requirements for single element pitch diameter gages. Users of this document shall apply the information described herein for the evaluation of the capability of their measurements based on the measurement consumer risk. It involves the analysis of the measurement (product) distribution and biases of both the product and measurement system distributions. It protects the consumer from the worst case distribution results. A whitepaper has been developed to provide supporting documentation and the rationale used in the development of this standard. This whitepaper will be published by the SAE as an Aerospace Information Report (AIR6553).
Standard
THREADED FASTENER PROTRUSION THROUGH SELF-LOCKING NUTS
1995-05-01
HISTORICAL
ARP1515
The external threaded fastener protrusion shall be defined as the external threads including the chamfer which extend through the top surface of the nut, see figure 1.
