Search Results

This paper presents, chemistry, test data and processing procedures on a non toxic and environmentally friendly chrome-free conversion coating alternative with the same level of adhesion and secondary corrosion resistance as that found in chrome containing conversion coating systems. Test data from military and independent sources will be presented on secondary coating adhesion, electrical conductivity, filiform and neutral salt-spray corrosion resistance as compared to chromate based systems .on magnesium, aluminum and zinc and their respective alloys. The European “RoSH” initiative will not allow for the presence of any hexavalent chromium on imported electrical components as of July first of 2006. Trivalent chromium based systems generate hexavalent chromium due to the oxidation of the trivalent chromium and as such will not be allowed.

In recent years there has been increasing interest in quantifying the emissions from aircraft in order to generate inventories of emissions for climate models, technology and scenario studies, and inventories of emissions for airline fleets typically presented in environmental reports. The preferred method for calculating aircraft engine emissions of NOx, HC, and CO is the proprietary “P3T3” method. This method relies on proprietary airplane and engine performance models along with proprietary engine emissions characterizations. In response and in order to provide a transparent method for calculating aircraft engine emissions non proprietary fuel flow based methods 1,2,3 have been developed. This paper presents derivation, updates, and clarifications of the fuel flow method methodology known as “Fuel Flow Method 2”.

THIS PAPER reviews VTOL problems, indicating probable ways toward optimization of whole lifting and propelling system. Also discussed are the power and thrust requirements for optimum cruise and vertical take-offs and landings for propeller-driven and jet-propelled aircraft. Three speed ranges offer the most promise for VTOL aircraft, if thrust requirements for cruise and take-off are to match. The ranges are centered around Mach numbers of 0.65, 0.8, and 2.0+. There is a possibility of overcoming the high thrust needed for hovering by use of bypass augmentation, special hovering jets, or favorable ground effects, the author reports.

THE optimum mode of control for an aircraft engine is dependent on both the configuration of the engine and its application. Each engine application requires several detail modes of control, one for each definable regime of operation of the engine. Discussions of control requirements can be simplified by classifying these regimes by objectives: physical limiting, thrust, and transient control. The turbojet engine is the basis for the discussion in this paper. Acceptable modes of control can often be selected by inspection of the engine and its application. Selection of an “optimum” control mode requires investigation of the operation of the engine and weapons system at every stage of its use. The selection of a “mode” of control requires a compromise between performance and other design factors. The need for simplicity and accuracy must be balanced against the stability requirements. The availability and flexibility of control components may limit the modes of control considered.

STRUCTURAL MATERIALS for Mach 3 jet transports pose difficult problems for the design engineer. Reasons for this problem are the incomplete information available on the many possible metals and the diversity of critical properties that are added by supersonic requirements. The material properties discussed in this paper include tensile strength, resistance to crack propagation, ease of fabrication, weldability, and thermal expansion. Cost factors are also considered. The structural configuration of the wing and fuselage is an example of the complexity of the material selection problem. The wing may be rigidity-critical, and the fuselage strength-critical; each requires diferent material properties to solve the problem.*

NEW WELDING processes are dropping costs while providing improvements in weld quality. This paper describes some of the more promising new developments in pressure and fusion welding and brazing. Included in the discussion are ultrasonic, high frequency resistance, foil seam, magnetic force, percussion, friction, and thermopressure welding and diffusion bonding. The description of adhesive bonding includes the development of glass or ceramic materials as structural adhesives.*

THIS PAPER presents the development of the DC-8 suppressor and thrust brake unit from initial test work through the final design. The selection of the production unit was based on a wide background of test work using both model and full-scale facilities. On the basis of this work, the configuration selected for production consisted of a fixed, corrugated, suppressing nozzle with a retractable ejector. A target-type thrust brake, mounted in the ejector, was chosen for the thrust brake production unit. Approximately 12-db suppression and 44% reverse thrust are provided by the unit. The ejector is hydraulically operated and the thrust brake air actuated. Both actuation systems obtain power from the aircraft systems which provides for operation during engine-out conditions. Alternate methods of actuation are provided in case of a primary system failure.

In a 2-year program sponsored by SJAC, an aqueous electroplating process using alkaline Zn-Ni with trivalent chromium post treatment is under evaluation for high strength steel for aircraft application as an alternative to cadmium. Commercial Zn-15%Ni rack/barrel plating solutions are basis for plating aircraft parts or fasteners. Brightener was reduced from the original formula to form porous plating that enables bake-out of hydrogen to avoid hydrogen embrittlement condition. Properties of the deposit, such as appearance, adhesion, un-scribed corrosion resistance, and galvanic corrosion resistance in contact with Al alloy, were evaluated. Coefficient of friction was compared with Cd plating by torque-tension measurements. Evaluation of the plating for scribed corrosion resistance, primer adhesion, etc. will continue in FY2007.

Combat aircraft maneuvering at high angles of attack or in landing approach are likely to encounter conditions where the flow over the swept wings is yawed. This paper examines the effect of yaw on the spectra of turbulence above and aft of the wing, in the region where fins and control surfaces are located. Prior work has shown the occurrence of narrowband velocity fluctuations in this region for most combat aircraft models, including those with twin fins. Fin vibration and damage has been traced to excitation by such narrowband fluctuations. The narrowband fluctuations themselves have been traced to the wing surface. The issue in this paper is the effect of yaw on these fluctuations, as well as on the aerodynamic loads on a wing, without including the perturbations due to the airframe.

MBB and Rockwell, under DARPA/NAVAIR and GMOD contract, are currently designing an experimental aircraft which will be dedicated to demonstrate “enhanced fighter maneuverability” (EFM) and supermaneuverability in particular. The aircraft is designed to break one of the last barriers left in aviation, the stall barrier. It will be able to perform tactical maneuvers up to 70° angle of attack and thus achieve very small radii of turn. Such highly instantaneous 3-dimensional maneuvers are of significant tactical value in future air combat with all aspect weapons. Key to the penetration into this unexplored flight regime is thrust vectoring in pitch and yaw. This feature is also used to enhance agility in critical flight conditions and to enhance the decoupling of fuselage aiming and flight path control as required for head-on gun firing.

Agile aircraft (X-29, X-31, F-18 High Alpha Research Vehicle, & F-16 Multi-Axis Thrust Vector) test pilots, while flying at high angles of attack, experience difficulty predicting their flight path trajectory. To compensate for the loss of this critical element of situational awareness, the X-31 International Test Organization (ITO) installed and evaluated a helmet mounted display (HMD) system into an X-31 aircraft and simulator. Also investigated for incorporation within the HMD system and flight evaluation was another candidate technology for improving situational awareness - three dimensional (3D) audio. This was the first flight test evaluating the coupling of visual and audio cueing for aircrew aiding. The focus of the endeavor, which implemented two visual and audio formats, was to examine the extent visual and audio orientation cueing enhanced situational awareness and improved pilot performance during tactical flying.

The X-29 Fuel/Auxiliary Oil Thermal Management System provides total aircraft accessory oil cooling, including both flight and combined hydraulics, Integrated Drive Generator oil, and Accessory Drive Gearbox oil, with onboard fuel. Fuel cooling rates that are independent of engine demand are achieved through the use of a recirculation loop. Recirculation is minimized by maintaining the engine fuel inlet temperature at the maximum allowable. Fuel cooling results in lower, more uniform subsystem oil temperatures, less ram drag, and smaller, lighter-weight heat exchangers. Initial design studies and laboratory development testing will be discussed, along with comparisons of analytical predictions with flight test results.

Paralleling synchronous generators requires a priori voltage matching and frequency synchronization. Exceeding normal limits can lead to severe electrical transients. The classical three-phase short circuit analysis is extended to include the case of two initially unloaded synchronous generators. An analytical solution is developed neglecting winding resistances and saturation. Of particular interest is the tendency to induce negative field currents that cause inverse voltages across the rotating rectifier in a brushless design. Typical aircraft generator parameters are used to predict the paralleling transient vs. initial rotor electrical angle mismatch. Results are compared to simulation and limited test results.

The Convair/Navy XFY-1 VTOL fighter was ahead of its time. In the early 1950s it became the first airplane to take off vertically, hover, transition to high speed level flight, transition back to hover, and land vertically. Pilot “Skeets” Coleman made a number of successful flights at Moffett Field South of San Francisco, at Brown Field near the California/Mexican border, and at San Diego's Lindbergh Field. This “first of a kind” aircraft soon adopted the name “POGO”. The POGO with its stall proof delta wing had near perfect aerodynamic characteristics in hover, transition and level flight. There were no “black boxes” needed for stability augmentation. The POGO was one of the very first aircraft to use hydraulic power flight controls - a system used today on all modern fighter and transport aircraft.