Refine Your Search

Topic

Author

Affiliation

Search Results

Viewing 1 to 20 of 13562
Technical Paper

“Use Of 75ST In Structural Applications”

1947-01-01
470140
The material known as 75ST is a new high strength aluminum alloy that can be used in certain aircraft structural applications to effect a saving in weight or an increase in strength or both over designs using other alloys. However, the structural engineer should be well acquainted with the advantages and limitations of this material before utilizing it in design.
Technical Paper

“RoHS” Compliant Chrome - Free Conversion Coating for Aerospace Manufacturing

2006-09-12
2006-01-3130
This paper presents, chemistry, test data and processing procedures on a non toxic and environmentally friendly chrome-free conversion coating alternative with the same level of adhesion and secondary corrosion resistance as that found in chrome containing conversion coating systems. Test data from military and independent sources will be presented on secondary coating adhesion, electrical conductivity, filiform and neutral salt-spray corrosion resistance as compared to chromate based systems .on magnesium, aluminum and zinc and their respective alloys. The European “RoSH” initiative will not allow for the presence of any hexavalent chromium on imported electrical components as of July first of 2006. Trivalent chromium based systems generate hexavalent chromium due to the oxidation of the trivalent chromium and as such will not be allowed.
Technical Paper

the development of Refractory Sheet Metal Structures

1960-01-01
600041
THIS PAPER REPORTS on the present state of the art in the utilization of refractory metals for air frame and powerplant sheet metal components. By far the most promising of these metals to date is molybdenum. The mechanical and physical properties of molybdenum are well-suited for high-temperature service. The combination of relatively high thermal conductivity, low thermal expansion coefficient, good specific heat, and a reasonably high emissivity of a coated surface make this material suitable for exterior surface application on severely aerodynamically heated components. However, in its usable alloyed forms, molybdenum tends to behave in a brittle manner at room temperature, suffering from a high brittle-to-ductile transition temperature. Other unacceptable properties are the presence of laminations in the material, 45-deg preferred angle cracking, and difficulty of controlling interstitial alloying elements. The authors discuss each of these and the progress made in overcoming them
Technical Paper

the Machining of Ultra-Strength Alloys

1960-01-01
600005
THE AIR FORCE has set up a program to evaluate the machining characteristics of the more commonly used high-strength thermal-resistant materials. This paper describes the test results to date. Four materials are being tested: SAE 4340 quenched and tempered to 50–55 Rockwell C, SAE designation H11 quenched and tempered to 50–55 Rockwell C, AM-350 solution treated and aged, and A-286 solution treated and aged. Machining tests include: turning milling, drilling, and tapping.*
Article

Zwick Roell provides flexible materials testing over a wide temperature range

2018-10-19
To enable the tests required for development work to be performed with maximum efficiency, the Zwick Roell Group (ZwickRoell) – a global supplier of materials testing machines based out of Ulm, Germany – developed a materials testing machine that can be equipped with both a temperature chamber and a high-temperature furnace.
Technical Paper

Zn-Ni Plating as a Cadmium Alternative

2007-09-17
2007-01-3837
In a 2-year program sponsored by SJAC, an aqueous electroplating process using alkaline Zn-Ni with trivalent chromium post treatment is under evaluation for high strength steel for aircraft application as an alternative to cadmium. Commercial Zn-15%Ni rack/barrel plating solutions are basis for plating aircraft parts or fasteners. Brightener was reduced from the original formula to form porous plating that enables bake-out of hydrogen to avoid hydrogen embrittlement condition. Properties of the deposit, such as appearance, adhesion, un-scribed corrosion resistance, and galvanic corrosion resistance in contact with Al alloy, were evaluated. Coefficient of friction was compared with Cd plating by torque-tension measurements. Evaluation of the plating for scribed corrosion resistance, primer adhesion, etc. will continue in FY2007.
Technical Paper

XB-70A Laboratory for Progress

1966-02-01
660276
The development of the XB-70 research aircraft produced advancements in many fields of technology. This paper covers a few of these advancements in the areas of materials, equipment, and manufacturing. These include honeycomb construction, PH 15-7 alloy steel, vacuum melted H-11 steel, equipment capable of withstanding high temperatures, chemical milling of many different alloys, miniaturized welding equipment, and exothermic brazing techniques.
Technical Paper

X-Ray Rocking Curve Analysis of the Aging and Deformation Characteristics in the Al-Li Alloy

1989-04-01
891057
A non-destructive x-ray technique, the double crystal diffractometer method, is presented as a tool to investigate the aging and deformation behavior of the Al-Li alloy. This is a sensitive method for measuring the strain and dislocation density within individual grains through the x-ray rocking curve. In addition, models were developed to describe the aging and deformation characteristics of this alloy.
Training / Education

Wrought Aluminum Metallurgy

Anytime
There are a wide variety of wrought aluminum alloys, each developed to provide specific properties. Getting the strength you need in an aluminum alloy requires knowledge of the effects of alloy composition, cold-working, and heat treating on aluminum metallurgy and properties. A good understanding of how aluminum alloys behave and what can be done to modify their properties is critical for being more productive and profitable. The course takes about one hour to complete and consists of one module and a final exam. Also, quizzes and problems give you opportunities to apply the concepts taught.
Standard

Wrenches; Flare Nut, Crowfoot, 12-Point Nondistorting

1993-03-01
HISTORICAL
AS4167A
This SAE Aerospace Standard (AS) covers 12-point open box end crowfoot, flare nut, double open box end, combination box and open box end, and ratcheting open box end wrenches that are designed with the following requirements: a Nondistorting usage b Possessing the strength, clearances, and internal wrenching design to be used on hydraulic tube fittings that conform to the requirements of SAE J514. c Transmitting torque to tube fittings without bearing on the apex of fitting wrenching points. Inclusion of dimensional data in this document is not intended to imply that all of the products described herein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes.
Standard

Wrenches; Flare Nut, Crowfoot, 12 Point Non-distorting

2011-04-26
HISTORICAL
AS4167B
This SAE Aerospace Standard (AS) covers 12 point flare nut crowfoot, flare nut wrenches, double end flare nut wrenches, combination box and flare nut wrenches, and ratcheting flare nut wrenches that are designed with the following requirements: a. Non-distorting usage b. Possessing the strength, clearances, and internal wrenching design to be used on hydraulic tube fittings that conform to the requirements of SAE J514. c. Transmitting torque to tube fittings without bearing on the apex of fitting wrenching points. Inclusion of dimensional data in this document is not intended to imply that all of the products described herein are stock production sizes. Consumers are requested to consult with manufacturers concerning lists of stock production sizes.
X