Search Results

The aim of this work is to apply an innovative adaptive ℒ1 techniques to control flutter phenomena affecting highly flexible wings and to evaluate the efficiency of this control algorithm and architecture by performing the following tasks: i) adaptation and analysis of an existing simplified nonlinear plunging/pitching 2D aeroelastic model accounting for structural nonlinearities and a quasi-steady aerodynamics capable of describing flutter and post-flutter limit cycle oscillations, ii) implement the ℒ1 adaptive control on the developed aeroelastic system to perform initial control testing and evaluate the sensitivity to system parameters, and iii) perform model validation and calibration by comparing the performance of the proposed control strategy with an adaptive back-stepping algorithm. The effectiveness and robustness of the ℒ1 adaptive control in flutter and post-flutter suppression is demonstrated.

Mathematical modeling and control of artificial ecosystems, such as MELISSA, require first the study of physical and biological characteristics in optimal and limiting conditions. Following the previous determination of the stoichiometric equations (Spirulina compartment) and regarding the two phototrophic compartments of MELISSA (Rhodospirillaceae and Spirulina), we have first to focus our control study on the growth kinetics for the light source. In this paper, we recall the theoretical equations of microbial growth kinetics and emphasise the problem of the light transfer in a photobioreactor. We present their adaptations to our pilot plant taking into account technological and biological specifics (lamp spectrum, working illuminated volume, growth rate,…). We then develop the principles and structure of the control system and describe tests of both the hardware and software for several steady state configurations.

A “next generation” condensing heat exchanger for space systems has to satisfy demanding operational requirements under variable thermal and moisture loads and reduced gravity conditions. Mathematical models described here are used to investigate transient behavior of wetting and de-wetting dynamics in the binary porous system of porous tubes and porous cold plate. The model is based on the Richard's equation simplified for the zero-gravity conditions. The half-saturation distance or the zone of influence of the porous annular suction tubes on the cold-plate porous material will be in the range of 1 to 10 cm for the time scales ranging from 100 to 10,000 seconds and moisture diffusivity in the range of D = 10-4 to 10-6 m2/s.

This specification covers a zinc alloy in the form of die castings.

(From Standards Proposal No. 2358, formulated under the cognizance of the EIA Quality and Reliability Engineering (QRE) Committee.)

Conventional attribute sampling plans based upon nonzero acceptance numbers are no longer desirable. In addition, emphasis is now placed on the quality level that is received by the customer. This relates directly to the Lot Tolerance Percent Defective (LTPD) value or the Limiting Quality Protection of MIL-STD-105. Measuring quality levels in percent nonconforming, although not incorrect, has been replaced with quality levels measured in parts per million (PPM). As a result, this standard addresses the need for sampling plans that can augment MIL-STD-105, are based upon a zero acceptance number, and address quality (nonconformance) levels in the parts per million range. This document does not address minor nonconformances, which are defined as nonconformances that are not likely to reduce materially the usability of the unit of product for its intended purpose.

This paper describes the development of a set of algorithms that find the takeoff gross weight of an aircraft for given vehicle and engine characteristics, and mission requirements. A major objective was to find the most elementary set that would still yield useful answers. The result was a set that could be encoded on an inexpensive programmable pocket calculator with only 24 lines of code. Results are compared with actual characteristics of an executive jet and its derivative versions.

This specification covers a zinc alloy in the form of die castings.

This specification covers one type of bronze in the form of round wire 0.500 inch (12.70 mm) and under in nominal diameter (see 8.5).

This paper discusses the importance of enroute wind conditions and the need for a wind measurement system which provides accurate and timely observations of wind and temperature conditions aloft. Recent advances in remote measurement of winds, temperature, and humidity such as the Stratospheric-Tropospheric radars and profilers developed at the National Oceanic and Atmospheric Administration’s Environmental Research Lab form the basis of such a system. A domestic system could and should be established using these devices together with a near real time winds aloft data dissemination network. Estimates of the saving in aircraft fuel consumption benefits range from 1 to 3 percent per year, or from $ 100 to $ 300 million for U.S. aviation system users at current prices and consumption.

This paper is concerned with the development of statistical models for the gust field in the lowest 300 ft of the atmosphere. It presents some of the highlights of the underlying physics principles, what is known about gusts, and how gusts affect aircraft. The difficulties of developing gust models are accounted for by the lack of data in particular areas and thus direct attention to the work required to provide the needed information.

This paper was prepared to support supersession of MIL-S-8879C with Screw Thread Conformity Task Force selected industry standard AS8879C, published by the Society of Automotive Engineers (SAE). Other documentation changes will be covered by separate papers. Separate papers are anticipated for thread gaging issues, and thread gage calibration procedures. The STC-TF decided that the thread design standard needed to be completed before thread gage definition could be addressed. Thread gage definition has to be known before calibration procedures can be addressed.

This document recommends supplementary design criteria to enhance endurance and reliability of transport aircraft wheels and brakes.

This document recommends supplementary design criteria to enhance endurance and reliability of transport aircraft wheels and brakes.

This document recommends supplementary design criteria to enhance endurance and reliability of transport aircraft wheels and brakes.

Unmanned Aerial Vehicles (UAV) are being deployed in military, law enforcement, search & rescue, scientific research, environmental & climate studies, reconnaissance and other commercial and non-commercial applications on a large scale. A design and development of landing gear system has been taken up for a UAV. This paper presents the design optimization of structural components of Wheel-Brake & Fork assembly pertaining to the Main Landing Gear (MLG) for a UAV. The wheel, fork, axle and brake unit constitute the wheel assembly. The wheel-brake assembly is assembled with the strut assembly and forms the Landing gear system. The Fork is the connecting member between the shock strut and the axle containing the wheel-brake assembly. As the fork and axle are subjected to shock loads while landing, the strength of these components are very much essential to withstand the dynamic loads.

Premature wearout of augmentor hydraulic fuel pumps was being experienced in service on a fighter aircraft engine. The removal times ranged from 150 to 800 engine operating hours. Considerable effort had gone into the understanding of the physics of failure and overcoming this problem in a modified pump. However, there still remained the question of how best to proof test the new pump. The challenge was to demonstrate that the redesigned pump was significantly better than the old pump. The problems faced during design verification will be discussed in this case study. For example, does an accelerated test duplicate the service failure mode? When has an accelerated test run long enough to prove the redesign is in fact better than the old product? This paper illustrates the application of new technology to solve these research and development program problems through the use of Weibull and Weibayes Analysis.

RMS (Reliability-Maintainability-Safety-Supportability) engineering is emerging as the newest discipline in product development due to new credible, accurate, quantitative methods. Weibull Analysis is foremost among these new tools. New and advanced Weibull techniques are a significant improvement over the original Weibull approach. This workshop, originally developed by Dr. Bob Abernethy, presents special methods developed for these data problems, such as Weibayes, with actual case studies in addition to the latest techniques in SuperSMITH® Weibull for risk forecasts with renewal and optimal component replacement.

The purpose of this SAE Aerospace Standard (AS) is to provide guidelines for the components and configurations that define the four versions of the Weather Support to Deicing Decision Making (WSDDM) winter weather nowcasting system.