Search Results

This paper will discuss using Astronics “Smart Panel” illuminated control panels to control an electronic power distribution system. A discussion of wiring simplification, automatic control possibilities and real time load monitoring is presented. The challenges of retrofitting the system into older aircraft will be covered as well. The paper also explains Electronic Circuit Breaker technology, arc fault protection, panel lighting technologies, control bus options, displays, and human input technology (buttons and knobs).

This paper presents the derivation of the equations for circumferential, longitudinal and radial heat transfer conductance for a thin shell toroid or a segment of the toroid. A thin shell toroid is one in which the radius to thickness ratio is greater than 10. The equations for the surface area of a toroid or of a toroidal segment will also be derived along with the equation to determine the location of the centroid. The surface area is needed to determine the radial conductance in the toroid or toroidal segment and the centroid is needed to determine the heat transfer center of the toroid or toroidal segment for circumferential and longitudinal conductance. These equations can be used to obtain more accurate results for conductive heat transfer in toroid which is a curved spacecraft components. A comparison will be made (1) using the equations derived in this paper which takes into account the curvature of the toroid (true geometry) and (2) using flat plates to simulate the toroid.

During several ISS missions, there were false alarms at both US and Russian smoke detectors. High local airborne particulate concentrations and interior deposits are considered the causes for such anomalies. Alternatives are proposed to replace or complement these faulty smoke detectors. The entrained zeolite particles may play a role in causing problems with check valves and air save pumps in CDRA and Vozdukh. Another incidence has been the dispersion of particulates out of Metox regeneration oven. Particulate matters with aerodynamic diameter of 15 microns and above, which normally settle down on earth, stay airborne under micro-gravity and thereby cause the above-mentioned nuisances. The motion of such a particle along a gas stream with an initial velocity can be expressed by theoretical equations. Stokes' Law leads to the descriptions of inertial precipitation of aerosols that are important in solving the issues.

This Life Support Laboratory consists of a simulator of the spacecraft called Nautilus, which houses Air Revitalization Subsystem, Atmospheric Control and Supply, and Fire Detection and Suppression in the Equipment Area. There are supporting facilities including a Human Metabolic Simulator, simulated Low and Moderate Temperature Coolant Loop, chemical analysis bench, purified water supply, vacuum and gas supplies. These facilities are scheduled to be completed and start to operate for demonstration purposes by March 2005. There are an ARES Ground Model (AGM) and a Trace Contaminant Control Assembly in the ARS. The latter will be integrated with the AGM and a Condensing Heat Exchanger. The unit of AGM is being engineered, built, and will be delivered in early 2005 by EADS Space Division. These assemblies will be operated for sensitivity analysis, integration and optimization studies. The main goal is the achievement for optimal recovery of oxygen.

SOME POSSIBILITIES for shortening the field length requirements of present-day jet aircraft are: Install leading-edge, high-lift devices which are retrofitable to present-day aircraft. Retrofit — or purchase new — aircraft powered by turbofan engines. These have an inherently higher take-off thrust to cruise thrust ratio than the jets, which vastly improves the take-off acceleration. Use boundary-layer control actuated by turbine discharge gas for immediate consideration in new aircraft engines. Use direct-lift jet engines. These will improve the block speed characteristics of the aircraft and also give vertical take-off and landing capabilities. This paper discusses the advantages of each of these possibilities. The author also describes the problem of airport location within a city, and its effect of total travel time.*

THE FIRST YEAR of jet airline operation has brought many problems — and satisfactions — to the industry. Here the author discusses some of the more serious problems: 1. Scheduling. American Airlines used the “Monte Carlo” method to calculate payloads and flight times. 2. Baggage handling. Almost nothing annoys a passenger more than long waits for baggage at the end of a flight. One approach to the problem is the baggage expediter system. 3. Mechanical shutdowns. 4. Runway length. 5. Noise. Noise suppressors have not been effective enough, from the standpoint of communities surroundings airports. Development of the turbofan engine offers some hope in this area.*

HEAT TRANSFER causes loading and starting design problems in large missile systems powered by cryogenic propellants. This manifests itself during loading as effective density variation, violent surface conditions, boiloff, and ice formation — problems which may be solved by insulating the tank. During starting it causes overheating and caviation — effects which may be reduced by recirculators and subcooled charge injections. The study described in this paper centers around liquid oxygen and its variations in heat flux rate, which affect liquid density, surface condition, and replenishing requirements. The problem areas are made apparent by consideration of a hypothetical missile system.*

THE optimum mode of control for an aircraft engine is dependent on both the configuration of the engine and its application. Each engine application requires several detail modes of control, one for each definable regime of operation of the engine. Discussions of control requirements can be simplified by classifying these regimes by objectives: physical limiting, thrust, and transient control. The turbojet engine is the basis for the discussion in this paper. Acceptable modes of control can often be selected by inspection of the engine and its application. Selection of an “optimum” control mode requires investigation of the operation of the engine and weapons system at every stage of its use. The selection of a “mode” of control requires a compromise between performance and other design factors. The need for simplicity and accuracy must be balanced against the stability requirements. The availability and flexibility of control components may limit the modes of control considered.

eROSITA (extended ROentgen Survey with an Imaging Telescope Array) is a powerful X-ray telescope under development by the Max-Planck-Institut für extraterrestrische Physik (MPE) in Garching, Germany. eROSITA is the core instrument on the Russian SRG1 mission which is planned for launch in 2011. It comprises seven nested Wolter-I grazing incidence telescopes, each equipped with its own CCD camera. The mirror modules have to be maintained at 20°C while the cameras are operated at -80°C. Both, mirrors and CCDs have to be kept within tight limits. The CCD cooling system consists of passive thermal control components only: two radiators, variable conductance heat pipes (VCHP) and two special thermal storage units. The orbit scenario imposes severe challenges on the thermal control system and also on the attitude control system.

The scope is determine if an 'Electronic Authorized Release Certificate' is viable and what is needed to make it viable.

THE performance characteristics of various devices applicable for jet directional control, lift augmentation, and VTOL-STOL studied at the NACA Lewis Laboratory are discussed, including jet deflection devices applicable to the conventonal round nozzle and novel nozzle configurations. The results indicate that many of the deflection devices applicable to conventional nozzles can readily be used for directional control or lift augmentation. Other deflection devices, such as movable plug, internal flap, cylindrical thrust reverser, swiveled primary with fixed shroud, and 90 deg side-bleed nozzle, are limited in application to jet directional control or aircraft trim because the loss in axial thrust for a given deflection force is prohibitive or the maximum deflected force obtainable is limited.

SUBSTANTIAL POWER is necessary to start the modern jet engine. Thus, starting equipment has become a major concern of air transport operators. This paper discusses the equipment used with self-contained starting systems. The authors discuss and evaluate a variety of self-contained systems: combustor, fuel-air combustion, cartridge, liquid propellant, hydraulic supported by auxiliary power units, and electric supported by APU. Possible future systems are: self-breathing systems, oxygen combustors, and liquid-oxygen-water-fuel combustors. It is emphasized that the choice of a starting system for a particular aircraft will depend on aircraft characteristics and the aircraft's intended use.*

To enable the tests required for development work to be performed with maximum efficiency, the Zwick Roell Group (ZwickRoell) – a global supplier of materials testing machines based out of Ulm, Germany – developed a materials testing machine that can be equipped with both a temperature chamber and a high-temperature furnace.

The likelihood of transmission of potential disease agents between animals and man during spaceflight is a real concern. Development of disease exclusion lists for animals and refinement of animal containment units have been the principal means of providing protection to the crew members. Awareness of potential latent infections and a judicious use of the higher risk category of animals such as wild-caught nonhuman primates provides another level of protection. Use of high efficiency filters, gasketing, and differential air pressures have all enabled increasing levels of safety through containment of potential aerosol escape from animal habitats.

A “next generation” condensing heat exchanger for space systems has to satisfy demanding operational requirements under variable thermal and moisture loads and reduced gravity conditions. Mathematical models described here are used to investigate transient behavior of wetting and de-wetting dynamics in the binary porous system of porous tubes and porous cold plate. The model is based on the Richard's equation simplified for the zero-gravity conditions. The half-saturation distance or the zone of influence of the porous annular suction tubes on the cold-plate porous material will be in the range of 1 to 10 cm for the time scales ranging from 100 to 10,000 seconds and moisture diffusivity in the range of D = 10-4 to 10-6 m2/s.

This specification covers a zinc alloy in the form of die castings.

Future space exploration missions will require a lightweight spacesuit that expends no consumables. This paper describes the design and performance of a prototype heat rejection system that weighs less than current systems and vents zero water. The system uses regenerable LiCl/water absorption cooling. Absorption cooling boosts the heat absorbed from the crew member to a high temperature for rejection to space from a compact, non-venting radiator. The system is regenerated by heating to 100°C for two hours. The system provides refrigeration at 17°C and rejects heat at temperatures greater than 50°C. The overall cooling capacity is over 100 W-hr/kg.

Spacecraft life support equipment is often challenged with two phase flow, where liquid and gas exist together. In the zero gravity environment of an orbiting spacecraft, the behavior of a liquid/gas interface is dominated by forces not usually observed in one “G” due to the overwhelming effects of gravity. The normal perceptions no longer apply. Water does not run down hill and bubbles do not rise to the surface. Surface energy, capillary forces, wetting characteristics and momentum effects predominate. Techniques and equipment have been developed to separate the liquid/gas mixture into its constituent parts with various levels of efficiency and power consumption.

The commercial aviation currently accounts for roughly 2.5 % of the global CO2 emissions and around 3.5% of world warming emissions, taking into account non CO2 effects on the climate. Its has grown faster in recent decades than the other transport modes (road, rail or shipping), with an average rate of 2.3%/year from 1990 to 2019, prior to the pandemic. Moreover, its share of Greenhouse (GHG) emissions is supposed to grow, with the increasing demand scenario of air trips worldwide. This scenario might threaten the decarbonization targets assumed by the aviation industry, in line with the world efforts to minimize the climate effects caused by the carbon emissions. In this context, hydrogen is set as a promising alternative to the traditional jet fuel, due to its zero carbon emissions.