Search Results

Automotive structural components are exposed to high loads, impact situations and corrosion. In addition, there may be temperature excursions that introduce creep as well as reduced modulus (stiffness). These issues have limited the use of light metals in automotive structural applications primarily to aluminum alloys, and primarily to cast wheels and knuckles (only a few of which are forged), cast brake calipers, and cast control arms. This paper reports on research performed at Chongqing University, Chongqing China, under the auspices of General Motors engineering and directed by the first author, to develop a protocol that uses wrought magnesium in control arms. The goal was to produce a chassis part that could provide the same engineering function as current cast aluminum applications; and since magnesium is 33% less dense than aluminum, would be lighter.

Measured vehicle loads have traditionally been used as the basis for development of component, subsystem and vehicle level durability tests. The use of measured loads posed challenges due to the availability of representative hardware, scheduling, and other factors. In addition, stress was placed on existing procedures and methods by aggressive product development timing, variety in tuning and equipment packages, and higher levels of design optimization. To meet these challenges, General Motors developed new processes and technical competencies which enabled the direct substitution of analytically synthesized loads for measured data. This process of Virtual Road Load Data Acquisition (vRLDA) enabled (a) conformance to shortened product development cycles, (b) greater consistency between design targets and validation requirements, and (c) more comprehensive data.

There is an increasing demand in automated manufacturability analysis of metal castings at the initial stages of their design. This paper presents a system developed for virtual manufacturability analysis of casting components. The system can be used by a casting designer to evaluate manufacturability of a part designed for various manufacture processes including casting, heat treatment, and machining. The system uses computational geometrics and geometric reasoning to extract manufacturing features and geometry characteristics from a part CAD model. It uses an expert system and a design database consisting of metal casting, heat treatment and machining process knowledge and rules to present manufacturability analysis results and advice to the designer. Application of the system is demonstrated for the manufacturability assessment of automotive cast aluminum components.

In order to assess the possible ways of energy transfer from the various sources of excitation in a vehicle assembly to a given target location, frequency based substructuring technique and transfer path analysis are used. These methods help to locate the most important energy transfer paths for a specific problem, and to evaluate their individual effects on the target, thus providing valuable insight into the mechanisms responsible for the problem. The Source-Path-Receiver concept is used. The sources can be from the road surface, engine, transmission, transfer case, prop-shaft, differential, rotating components, chain drives, pumps, etc., and the receiver can be driver/passenger ears, steering column, seats, etc. This paper is devoted to identify the noise transfer paths and the force transmissibility among the interfaces of different components in the vehicle for the low to mid frequency range.

This paper presents subjective and objective methods for evaluating transient vehicle dynamics characteristics in four sections: (1) Definition of transient behavior in terms of four traits-agility, stability, precision, and roll support; (2) Description of subjective evaluation methods; (3) Implementation of Design for Six Sigma principles to the development of a steering robot controlled objective test for transient performance; (4) The final section of this paper uses data from simulation and road tests to demonstrate how chassis design parameters can affect transient handling performance.

Delivering the appropriate material data for CAE analysis of plastic components is not as straight forward as it would seem to be. While a few of the properties typically used by resin manufacturers and material engineers to describe a plastic are useful to the analysis community (density, CLTE), most are not (flexural modulus, notched izod). In addition some properties such as yield stress are defined differently by the analysis community than by the materials community. Lastly, secondary operations such as painting or chrome plating significantly change the behavior of components with plastic substrates. The materials engineering community and the CAE analysis community must work together closely to develop the material data necessary to increase the capability of the analysis. This paper will examine case studies where these issues have required modifications to the material property data to increase the fidelity of the CAE analysis.

Recently, an increased emphasis has been seen for improving the cooling uniformity and efficiency of HEV battery pack in an effort to increase the battery performance and life. This study examined the effects of geometry changes in cooling systems of battery packs on thermal behavior of battery cells and pressure drop across the battery pack. Initially, a multi-physics battery thermal model was correlated to physical test data. An analytical design of experiments (DOE) approach using Latin-hypercube technique was then developed by integrating the correlated battery thermal model with a commercial optimization code, iSIGHT, and a morphing code, DEP Morpher. The design concepts of battery pack cooling systems were finally identified by performing analytical DOE/optimization studies to estimate the effects of cooling flow and geometries of cooling ducts on the battery temperature variation and pressure drop across the battery pack.

General Motors and the Takata Corporation have worked together to bring to production a new, industry first technology called the Front Center Airbag which is being implemented on General Motors' 2013 Midsize Crossover Vehicles. This paper reviews field data, describes the hardware, and presents occupant test data to demonstrate in-position performance in far side impacts. The Front Center Airbag is an airbag that mounts to the inboard side of the driver front seat. It has a tubular cushion structure, and it deploys between the front seating positions in far side impacts, near side impacts and rollovers, with the cushion positioning itself adjacent the driver occupant's head and torso. This paper includes pictures of the technology along with a basic description of the design. In-position occupant performance is also described and illustrated with several examples. Single occupant and two front occupant far side impact test data are included, both with and without the airbag present.

This study evaluates utilizing an accelerated test method that correlates customer interaction with a vehicle seat where bagginess and wrinkling is produced. The evaluation includes correlation from warranty returns as well as test vehicle results for test verification. Consumer metrics will be discussed within this paper with respect to potential application of this test method, including but not limited to JD Power ratings. The intent of the test method is to aid in establishing appropriate design parameters of the seat trim covers and to incorporate appropriate design measures such as tie downs and lamination. This test procedure was utilized in a Design for Six Sigma (DFSS) project as an aid in optimizing seat parameters influencing trim cover performance using a Design of Experiment approach.

Temperature effects on the deformation and fracture of a commercially produced transformation-induced plasticity (TRIP) steel subject to a two-step quenching and partitioning (Q&P) heat treatment are investigated. Strain field evolution at room temperature is quantified in this 980 MPa grade Q&P steel with a stereo digital image correlation (DIC) technique from quasi-static tensile tests of specimens with 0°, 45°, and 90° orientations. Baseline tensile properties along with the variation of the instantaneous hardening index with strain were computed. Variations of the bake-hardening index were explored under simulated paint bake conditions. Tensile properties were measured at selected temperatures between -100°C and 200°C and the TRIP effect was found to be temperature-dependent due to stress-induced martensitic transformation at lower temperatures versus strain-induced transformation at higher temperatures.

As mass reduction becomes an increasingly important enabler for fuel economy improvement, having a robust structural development process that can comprehend Vehicle Dynamics-specific requirements is correspondingly important. There is a correlation between the stiffness of the body structure and the performance of the vehicle when evaluated for ride and handling. However, an unconstrained approach to body stiffening will result in an overly-massive body structure. In this paper, the authors employ loads generated from simulation of quasi-static and dynamic vehicle events in ADAMS, and exercise structural finite element models to recover displacements and deflected shapes. In doing so, a quantitative basis for considering structural vehicle dynamics requirements can be established early in the design/development process.

Experimental decklids for the Cadillac STS sedan were made with Al AA5083 sheet outer panels and Mg AZ31B sheet inner panels using regular-production forming processes and hardware. Joining and coating processes were developed to accommodate the unique properties of Mg. Assembled decklids were evaluated for dimensional accuracy, slam durability, and impact response. The assemblies performed very well in these tests. Explicit and implicit finite element simulations of decklids were conducted, and showed that the Al/Mg decklids have good stiffness and strength characteristics. These results suggest the feasibility of using Mg sheet closure panels from a structural perspective.

Magnesium and aluminum alloys offer lightweighting opportunities in automotive applications. Joining of dissimilar materials, however, generally requires methods that do not involve fusion. This paper explores the use of self-pierce riveting (SPR) to join magnesium to aluminum alloys for structural and closure applications. The preliminary results indicate that SPR is a viable option for joining aluminum extrusions to magnesium die castings, as well as stamped sheet aluminum to quick-plastic-formed (QPF) sheet magnesium.

This paper reports on a study that examines the effect of shoulder belt load limiters and pretensioners as well as crash and occupant factors that influence upper torso harm in real-world frontal crashes. Cases from the University of Michigan International Center for Automotive Medicine (ICAM) database were analyzed. Additional information was used from other databases including the National Highway Traffic Safety Administration (NHTSA) New Car Assessment Program (NCAP), the Insurance Institute for Highway Safety (IIHS), the National Automotive Sampling System - Crashworthiness Data System (NASS-CDS), and patient data available from the University of Michigan Trauma Center. The ICAM database is comprised of information from real-world crashes in which occupants were seriously injured and required treatment at a Level 1 Trauma Center.

Roof racks are designed for carrying luggage during customers' travels. These rails need to be strong enough to be able to carry the luggage weight as well as be able to withstand aerodynamic loads that are generated when the vehicle is travelling at high speeds on highways. Traditionally, roof rail gage thickness is increased to account for these load cases (since these are manufactured by extrusion), but doing so leads to increased mass which adversely affects fuel efficiency. The current study focuses on providing the guidelines for strategically placing lightening holes and optimizing gage thickness so that the final design is robust to noise parameters and saves the most mass without adversely impacting wind noise performance while minimizing stress. The project applied Design for Six Sigma (DFSS) techniques to optimize roof rail parameters in order to improve the load carrying capacity while minimizing mass.

This study concerns the generation of response surfaces for kinematics and injury prediction in pedestrian impact simulations using human body model. A 1000-case DOE (Design of Experiments) study with a Latin Hypercube sampling scheme is conducted using a finite element pedestrian human body model and a simplified parametric vehicle front-end model. The Kriging method is taken as the approach to construct global approximations to system behavior based on results calculated at various points in the design space. Using the response surface models, human lower limb kinematics and injuries, including impact posture, lateral bending angle, ligament elongation and bone fractures, can be quickly assessed when either the structural dimensions or the structural behavior of the vehicle front-end design change. This will aid in vehicle front-end design to enhance protection of pedestrian lower limbs.

This paper presents a method to reduce the number of occurrences of vehicle deceleration disturbances due to the reduction of regenerative braking in the presence of wheel slip. Usually, regenerative braking is disabled when wheel slip is detected in order to allow the ABS system to efficiently cycle brake pressure. When this happens, the vehicle will momentarily lose deceleration due to the reduction in both regenerative brake torque and friction brake pressure, until friction brake pressure is reapplied. Some ABS activations can be defined as nuisance events, in which full ABS control is not necessary and is exited rapidly; for example, a vehicle driving through a pothole. In these cases it is desirable to continue regenerative braking in order to keep vehicle deceleration as smooth as possible.

Industry standards and practices define a number of mathematical and physical methods to estimate the cargo carrying volume capacity of a vehicle. While some have roots dating back decades, others try to assess the utility of the space for cargo by subjective measurements. Each these methods have their own inherent merits and deficiencies. The purpose of this paper is to highlight the differences in calculated cargo volume amongst the following practices: Society of Automobile Engineers (SAE) J1100[1] International Organization for Standardization (ISO 3832)[2], Global Car manufacturer's Information Exchange group (GCIE)[3], Consumer Reports[4]. This paper provides a method and associated rationale for constructing a new cargo volume calculation practice that attempts to harmonize these procedures into a more contiguous practice. This homologation will benefit publishing industry, vehicle manufacturers and customers alike.

The imperative to get to the market faster with new and better products, has determined all automotive OEM to rethink their product development cycle, and, as a result, many hardware based processes were replaced and/or augmented with virtual, software based ones. However, the virtualization itself does not guaranties better and faster products. In the area of vehicle dynamics, we concentrate on improving the multi-body model development process, facilitating comprehensive virtual testing, and verifying the robustness of the design. The authors present a highly flexible and efficient environment that encourages, enforces, and facilitates model sharing, reusing of components, and parallelization of vehicle dynamics simulations, developed on top of an existing commercial off-the-shelf engineering software application.

Plug-in electric vehicles are becoming increasingly popular as the U.S. and other nations look for ways to reduce the usage of petroleum fuels and reduce the carbon emission footprint. Though plug-in electric vehicles offer many advantages over conventional vehicles, they also present some unique potential hazards due to the presence of high voltage in the vehicle. Specifically, potential high voltage hazards can occur if the electric vehicle is crashed by another vehicle during its plug-in charging session. High voltage hazards include the possibility of electrical shock and thermal events as a result of electrical arcing that can cause injury or death to persons that operate or work around plug-in electric vehicles. Automotive Safety Integrity Level (ISO 26262), often abbreviated as ASIL, is used by the automotive industry for determining the ranking of safety hazards.