Search Results

Visteon has developed a CAE procedure to qualify instrument panel (IP) products under the vehicle key life test environments, by employing a set of CAE simulation and durability techniques. The virtual key life test method simulates the same structural configuration and the proving ground road loads as in the physical test. A representative dynamic road load profile model is constructed based on the vehicle proving ground field data. The dynamic stress simulation is realized by employing the finite element transient analysis. The durability evaluation is based on the dynamic stress results and the material fatigue properties of each component. The procedure has helped the IP engineering team to identify and correct potential durability problems at earlier design stage without a prototype. It has shown that the CAE virtual key life test procedure provides a way to speed up IP product development, to minimize prototypes and costs.

A test load specification is required to validate an automotive product to meet the durability and design life requirements. Traditionally in the automotive industry, load specifications for design validation tests are directly given by OEMs, which are generally developed from an envelop of generic customer usage profiles and are, in most cases, over-specified. In recent years, however, there are many occasions that a proposed load specification for a particular product is requested. The particular test load specification for a particular product is generated based on the measured load data at its mounting location on the given type of vehicles, which contains more realistic time domain load levels and associated frequency contents. The measured time domain load is then processed to frequency domain test load data by using the fast Fourier transform and damage equivalent techniques.

A twenty-five kilowatt (peak power for one minute), permanent magnet electric machine for a hybrid electric vehicle application was designed and tested. The electric machine is located in the clutch housing of an automatically shifted manual transmission and is subjected to 120 °C continuous ambient temperatures. The package constraints and duty cycle requirements resulted in an extremely challenging thermal design for an electric machine. The losses in the machine were predicted using models based on first principles and the heat transfer in the machine was modeled using computational fluid dynamics. The simulations were compared to test results over a variety of operating conditions and the results were used to validate the models. Parametric studies were conducted to evaluate the performance of potting materials and cooling topologies.

Spark timing of an Internal Combustion (IC) engine is often limited by engine knock in the advanced direction. The ability to operate the engine at its advanced (borderline knock) spark limit is the key for improving output power and fuel economy. Due to combustion cycle-to-cycle variations, IC engine combustion behaves similar to a random process and so does the engine performance criteria, such as IMEP (Indicated Mean Effective Pressure), and knock intensity. The combustion stability measure COVariance of IMEP assumes the IMEP is a random process. Presently, the spark limit control of IC engines is deterministic in nature. The controller does not utilize any stochastic information associated with control parameters such as knock intensity for borderline spark limit control. This paper proposes a stochastic limit control strategy for borderline knock control. It also develops a simple stochastic model for evaluating the proposed stochastic controller.

Estimation and prediction of residual life and reliability are serious concerns in life cycle management for aging structures. Laboratory testing replicating fatigue loading for a typical military aircraft wing skin was undertaken. Specimens were tested until their fatigue life expended reached 100% of the component fatigue life. Then, scanning electron microscopy was used to quantify the size and location of fatigue cracks within the high stress regions of simulated fastener holes. Distributions for crack size, nearest neighbor distances, and spatial location were characterized statistically in order to estimate residual life and to provide input for life cycle management. Insights into crack initiation and growth are also provided.

This paper discusses the development of combination vehicle stability program (CVSP) at Visteon. It will describe why stability control is needed for combination vehicles and how the vehicle stability can be improved. We propose and evaluate controller structures and design methods for CVSP. These include driver's intent identification, combination vehicle status estimation and control, and fault detection / tolerance. In this paper, the braking and steering dynamics of car-trailer and tractor-semitrailer combinations, and the brake systems which should be used extensively to increase the stability of combination vehicles are presented. Also our development platform is introduced and the combination vehicle simulation results are presented. The definition of combination vehicles in this paper includes car-trailer and commercial tractor-semitrailer combinations since their vehicle dynamics are based on the same equations of motion.

In today's search for a better fuel economy and lower emissions, it is essential to precisely control the injected fuel quantity, as demanded by the engine load, into each of the engine cylinders. In fuel injection systems, the pressure pulsations due to the rapid opening and closing of the injectors can cause uneven injected fuel amounts between cylinders. In order to develop effective techniques to reduce these pressure pulsations, it is crucial to have a good understanding of the dynamic characteristics of such fuel injection systems. This paper presents the benefits of using simulation as a tool to analyze the dynamic behaviors of a V8 gasoline injection system. The fuel system modeling, based on a one-dimensional (1D) lumped parameter approach, has been developed in the AMESim® environment. The comparison between the simulation results and the experimental data shows good agreement in fluid transient characteristics for both time and frequency domains.

The present work demonstrates the application of Design of Experiments (DOE) statistical methods to the design and the improvement of a hydraulic steering pump noise, vibration, and harshness (NVH) performance in relief. DOE methods were applied to subjective ratings to examine the effect of several different factors, as well as the interactions between these factors on pump relief NVH. Specifically, the DOE was applied to the geometry of the cross ports on a hydraulic relief valve to improve “whistle” noise in the pump. Statistical methods were applied to determine which factors and interactions had a significant effect on pump whistle. These factors were used to produce a more robust cross port configuration reducing whistle noise. Lastly, the final configuration was experimentally verified on the test apparatus and subjectively confirmed in vehicle-level testing.

In this paper, an analytical procedure for prediction of shell radiated noise of air induction systems (AIS) due to engine acoustic excitation, without a prototype and physical measurement, is presented. A set of modeling and simulation techniques are introduced to address the challenges to the analytical radiated noise prediction of AIS products. A filter seal model is developed to simulate the unique nonlinear stiffness and damping properties of air cleaner boxes. A finite element model (FEM) of the AIS assembly is established by incorporating the AIS structure, the proposed filter seal model and its acoustic cavity model. The coupled acoustic-structural FEM of the AIS assembly is then employed to compute the velocity frequency response of the AIS structure with respect to the air-borne acoustic excitations.

As powertrains continue to get more efficient, less waste heat is available for warming the passenger compartment. Although several supplemental heating devices are currently on the market, including electric heaters, viscous heaters, and fuel operated heaters, they each have shortcomings related to cost, capacity, efficiency, and/or environmental concerns[1]. In an attempt to provide superior time-to-comfort in a cost, weight, package efficient, and environmentally friendly manner, an R134a heat pump (HP) system was developed. Several technical issues were overcome while developing this system. Production vehicles have been retrofitted to incorporate the R134a heat pump system and tested in a climatic wind tunnel. Test results for a -18°C warm-up test were compared to baseline data, showing significant improvements in average discharge air and breath level temperatures.

A suction line heat exchanger (SLHX) transfers heat from the condenser outlet to the suction gas. In a TXV (thermostatic expansion valve) system, the performance improvement with a 60 to 80 % effective SLHX is expected to be on the order of 8 to 10 % for capacity, and 5 to 7 % for COP for high outdoor air temperatures of 43ºC. In a FOT (fixed orifice tube) system, the performance improvement was calculated to be about 10 to 15 %. The calculated improvements have been verified experimentally within a few percent.

As global automobile manufacturers prepare for the phase-out of R134a in Europe, they must address the issue of using the new refrigerant for European sales only or launching the product worldwide. Several factors play into this decision, including cost, service, risk, customer satisfaction, capacity, efficiency, etc. This research effort addresses the minimal vehicle-level hardware differences necessary to provide a European solution of R1234yf while continuing to install R134a into vehicles for the rest of the world. It is anticipated that the same compressor, lubricant and condenser; most fluid transport lines; and in most cases the evaporator can be common between the two systems.

The objective of the present work was to improve the cold start NVH performance of an automotive power steering pump under low temperature conditions. This objective was accomplished through the use experimental study and measurement. The satisfactory operation of a fixed displacement vane pump in cold temperatures depends on a number of factors including; (1) filling characteristics, (2) the inlet conditions to the pump, (3) the fluid, and (4) the ability of the vanes to maintain contact with the cam surface. In this investigation, factor (4) was chosen for investigation. A unique outlet orifice was designed and tested at three different operating ambient temperatures, -19 °C, -29 °C, and -40 °C. Maximum “noise” duration was measured as the maximum duration of fluid borne pump outlet pressure oscillations greater the 345 kPa peak-to-peak. The results show that noise duration can reduced by as much as 50% at -40 °C.

The quietness of the interior of automobiles is perceived by consumers as a measure of quality and luxury. Great strides have been achieved in isolating interiors from noise sources. As noise is reduced, in particular wind and power train noise, other noise sources become evident. Noise reduction efforts are now focused on components like power steering pumps. To understand the contribution of power steering pumps a world-class noise and vibration test stand was developed. This paper describes the development of the test stand as well as it's objective to understand and improve the sound quality of power steering pumps.

Engine air filtration technologies currently used in air induction systems typically utilize pleated paper or felt type air filters. These air filter designs have been used for many years in panels, cylindrical or round (pancake type) type air cleaners. Pleated air filters are specifically designed to be serviceable and hence their performance is inherently limited by vehicle under-hood packaging and manufacturing constraints. Due to these constraints, majority of air cleaner designs are not optimized for engine filtration and air flow management under the hood. Studies show that use of low performing serviceable aftermarket air filters significantly affect the performance and durability of engine air cleaners [9]. High mileage studies confirm that engine durability, service issues, warranty field returns and customer satisfaction was affected by use of aftermarket filter brands.

In Brazil the market for plastic parts molds, in last few years had become very competitive, with several Vehicle Operations and a big number of a different models, and with today total market volume it means low volumes productions for each model. This market demands for good toolshops and at the same time a big pressure to reduce investments, one of the most important. Plastic components usage in the car, is increasing overtime, with new applications for Exterior, interior and powertrain, requiring new technologies for Injection molding processing and making molds to be more complex. The development of plastic parts in Brazil has its own characteristics, strengths and weaknesses. In fact a big and heterogeneous market. This paper intends to present an analysis of development of plastic parts in Brazil, considering the development of mold tooling locally, focusing the automotive market.

This paper presents an unambiguous and intuitive method for identification of steering column resonant (SCR) mode of vibration. One simple but overlooked technique to determine the SCR mode in-vehicle is to provide local stiffnesses of the body locations where the Instrument Panel (IP) attaches, to the IP suppliers to be used in their design and development. This paper describes how this technique is useful in predicting the first few important in-vehicle steering column modes for different classes of vehicles, with examples presented in each class. The results obtained from such analyses are compared against those from direct in-buck simulations. This technique is not limited to its application in developing IP systems, but can easily be extended to include other systems such as seats, fuel tanks, etc. Also it is shown that a design optimization analysis may be performed using these attachment stiffnesses as design variables resulting in a system level solution.

The increasing power requirement for automotive electronics (radios, etc.), combined with ever-shrinking size and weight allowances, is creating a greater need for optimization and robust design of heat sinks. Not only does a heat sink directly affect the overall performance and reliability of a specific electronics application, but a well-designed, optimized heat sink can have other benefits - such as eliminating the requirement for special fans, reducing weight of the application, eliminating additional heat sink support structures, etc. Optimizing heat sink efficiency and thermal performance offers a challenge, due to the many competing design requirements. These requirements include effecting greater temperature reductions, accommodating vehicle packaging requirements and size limitations, generating a uniform heat distribution, etc., and all the while reducing the heat sink cost.

The starter drive clutch is a one way roller clutch and a key component in a starter motor that is used to crank internal combustion engines. The starter drive clutch transmits torque from an electrical motor to a ring gear mounted on a cranking shaft in an engine thus cranks the engine. The clutch also prevents the whole starter from damage caused by extremely high load and/or extremely high speed applied to the starter pinion from the engine. Drive slippage and barrel cracking are two major failure modes for the starter drive[1]. Insufficient torque capacity results in drive slippage while excessive high hoop stress on the clutch barrel ring causes barrel crack. To eliminate drive slippage failure, the clutch should be designed with high torque capacity. High torque capacity, however, is a cause of high hoop stress on the barrel that may result in the cracked barrel failure. Higher torque capacity and lower hoop stress are two completely opposite design directions.

Engine air induction noise can play a significant role in the reduction of vehicle interior noise levels and tuning interior sound quality. Given the need to reduce prototyping and testing costs, it is important to gain an understanding of the level and frequency structure of the noise radiating from the open inlet of the air induction system. Engine simulation used independently can predict inlet noise; however, its utility is limited to systems that are largely one-dimensional. Systems that exhibit a three-dimensional nature, such as the wave dynamics in an engine air cleaner, require a more intensive approach. Boundary Element Analysis (BEA) has been demonstrated to be a tool that can be used to predict the frequency response of ducted systems and is particularly useful in highly three-dimensional systems.