Search Results

”U” bolts are fixing elements and they are used to clamp an elastic joint. From the past, they still looking as an old design and unfortunately, suspension engineers are not specialists in fasteners and elastic joints. That is why we will show important assumptions and concepts to design and specifications this clamp element “U” bolt and its influence over leaf-springs. Currently, “U” bolt is used to clamp an elastic or elastic-plastic joint of heavy duty suspension, formed by leaf-spring, axle, spring pad, “U” bolt plate. This kind of suspension is typically used to trucks, buses and trailers. We are wondering, which one important assumption that an engineer must be careful when designs a new suspension changing from old designs to an updated technology. We provide a theoretical analysis and a FEA analysis to compare torque efficacy x leaf-spring reactions and what are effects this relationship can cause in a suspension.

IT does not yet seem to be recognized fully that it is the local temperature at the surface of contact and not the local specific pressure that chiefly determines the occurrence of seizure under extreme-pressure-lubrication conditions. This local temperature is the result of the temperature level of the parts lubricated, considered as a whole (“bulk” temperature) and of a superimposed instantaneous temperature rise (temperature “flash”) which is localized in the surface of contact. It appears typical for extreme-pressure-lubrication conditions, as met in gear practice, that the temperature flash is much higher than the bulk temperature. With existing conventional test methods for the determination of the protection against seizure afforded by EP lubricants, a considerable rise of the bulk temperature mostly occurs; as it cannot be controlled sufficiently; thus, leaving an unknown margin for the temperature flash, it renders impossible a reliable determination.

There are many different vibration sources in a car. Engine, gears, road roughness, impacts against the wheels cause vibration and sound that can decrease the parts and the car durability as well as affect drivability, safety and passengers and community comfort. In 4×4 cars, some extra vibration sources are the parts responsible for transmitting the torque and power to the rear wheels. Each of them has their own vibration modes, excited mostly by its imbalance or by the second order engine vibration. The engine vibration is a very well known phenomena and the rear driveshaft is designed not to have any vibration mode in the range of frequencies that the engine works or its second order. The imbalance of a driveshaft is also a design requirement. That means, the acceptable imbalance of the driveshaft is limited to a maximum value.

Vehicle dynamics is a discipline of mechanical engineering that benefited of significant improvements thanks to the progress of computational engineering. Vehicle dynamics engineers are using CAE for the development of a vehicle with MBS and FEA. The concurrent use of these two technologies is a standard in the automotive industry. However the current simulation process is not fully efficient because local geometrical and material nonlinearities are not accurately modeled in classical MBS software. This paper introduces a methodology for vehicle dynamics simulation integrating MBS capabilities in one single nonlinear FEA environment enabling an accurate modeling of nonlinearity in vehicles.

Buick engineers are well pleased with their '69 Chassis. Benefits of a unique front suspension camber curve are documented. The effects of various suspension parameters on ride and handling are explained. These were varied independently of one another in the course of evaluating over 30 suspension configurations.

THE usefulness of planetary gear trains and the engineering techniques necessary for optimum design are discussed in this paper. A simple method for calculating planetary gear ratios is described which can be used to determine quickly the potential usefulness of any planetary configurations. The author lists criteria which help to evaluate the potential of a planetary gear train schematic from the standpoints of gear noise and structural viewpoint. Detailed design of individual members include spacing of the pinions, mounting considerations, thrust direction, lubrication, and stress evaluation.

Truck and bus manufacturers have been constantly facing an issue to disassemble the rear axle shaft from the hub when transporting the truck from the factory to the dealership. In addition to that, the dealerships have the very same problem every time they have to replace the brake pads in some truck models, which leads to excessive service time, extra costs and aftermarket complaints. The current problematic fastening system is composed by a lock nut, a flat washer and a coned slotted bushing. The concept of this 30 year old design involves the coned slotted bushing being pressed against a tapered hole on the shaft’s flange. After tightening the lock nut, the bushing clamps towards the stud and it gets stuck in between the shaft and the stud generating the problem described above. This paper shows the R&D process that Tekfor used to come up with the 1-piece fastener named iLokTM nut that replaces the problematic 3-piece fastening system.

This paper sets up a simplified dynamic model for simulating the yaw/roll stability of heavy tractor-semitrailer using Matlab/Simulink. A linear quadratic regulator (LQR) based on partial-state feedback controller is used to optimize the roll stability of the vehicle. The control objective for optimizing roll stability is to be reducing the lateral load transfer rate while keeping the suspension angle less than the maximum allowable angle. The simulation result shows that the LQR controller is effective in the active roll stability control of the heavy tractor-semitrailer.

Two methods for calculating speed from curved tire marks were investigated. The commonly used critical speed formula and a computer simulation program were evaluated based on their ability to reproduce the results of full-scale yaw tests. The effects of vehicle braking and friction coefficient were studied. Twenty-two yaw tests were conducted at speeds between 70 and 120 km/h. For half of the tests, about 30% braking was applied. Using the measured sliding coefficient of friction, both the critical speed formula and the computer simulations under-predicted the actual speed of the vehicle. Using the measured peak coefficient of friction, both methods over-estimated the actual speed. There was less variance in the computer simulation results. Braking tended to increase the speeds calculated by the critical speed formula.

In this paper, a gain-scheduling optimal control approach is proposed to enhance yaw stability of articulated commercial vehicles through active braking of the proper wheel(s). For this purpose, an optimal feedback control is used to design a family of yaw moment controllers considering a broad range of vehicle velocities. The yaw moment controller is designed such that the instantaneous tractor yaw rate and articulation angle responses are forced to track the target values at each specific vehicle velocity. A gain scheduling mechanism is subsequently constructed via interpolations among the controllers. Furthermore, yaw moments derived from the proposed controller are realized by braking torque distribution among the appropriate wheels. The effectiveness of the proposed yaw stability control scheme is evaluated through software-in-the-loop (SIL) co-simulations involving Matlab/Simulink and TruckSim under lane change maneuvers.

In this paper a yaw stability control algorithm along with an emergency roll control strategy have been developed. The yaw stability controller and emergency roll controller were both developed using linear two degree-of-freedom vehicle models. The yaw stability controller is based on Lyapunov stability criteria and uses vehicle lateral acceleration and yaw rate measurements to calculate the corrective yaw moment required to stabilize the vehicle yaw motion. The corrective yaw moment is then applied by means of a differential braking strategy in which one wheel is selected to be braked with appropriate brake torque applied. The emergency roll control strategy is based on a rollover coefficient related to vehicle static stability factor. The emergency roll control strategy utilizes vehicle lateral acceleration measurements to calculate the roll coefficient. If the roll coefficient exceeds some predetermined threshold value the emergency roll control strategy will deploy.

From the beginning of 1995 on, RB will start the production of the Vehicle Dynamics Control System. A key part of this system is the Yaw Rate Sensor described in this paper. The basic requirements for this sensor for automotive applications are: mass producibility, low cost, resistance against environmental influences (such as temperature, vibrations, EMI), stability of all characteristics over life time, high reliability and designed-in safety. Bosch developed a sensor on the basis of the “Vibrating Cylinder”. The sensor will be introduced into mass production in beginning of 1995.

In the current Ford Pro-Trailer Backup Assist (TBA) system, trailer hitch angle is determined utilizing the reverse camera of the vehicle. In addition to being sensitive to environmental factors such as lighting conditions and occlusion, the vision-based approach is difficult to be applied to gooseneck or fifth wheel trailers. In this paper, a yaw rate based hitch angle observer is proposed as an alternative sensing solution for TBA. Based on the kinematic model of the vehicle-trailer, an instantaneous hitch angle is first derived by utilizing vehicle yaw rate, trailer yaw rate, vehicle velocity and vehicle/trailer parameters provided by the TBA system. Due to signal errors and parameter uncertainties, this instantaneous hitch angle may be noisy, especially at lower vehicle speed.

A new controllable limited slip differential is proposed and tested in software environment. It is characterized by the employment of a magnetorheological fluid, which presents the property of changing its rheology thanks to an applied magnetic field. A vehicle model has been designed and employed for the synthesis of a sliding controller. The control is based on a double level scheme: the upper controller aims to generate the target locking torque, while the lower controller generates, as control action, the supply current for the controllable limited slip differential. The obtained results show the effectiveness of the device in terms of vehicle dynamics improvement. Indeed, the results reached by the vehicle in presence of the new differential confirm the improved performances for both steady and unsteady state manoeuvres.

Active vehicle dynamics control ensures improved safety. So far, yaw instability is mostly associated with transient steering manoeuvres when driving at a constant speed. However, braking related load transfer affects yaw stability. Intense braking at high friction combined with elevated and forwarded CG amplifies this influence on unloaded tractors. Designing a dynamic stability system to enhance active safety requires fresh insight into braking related yaw instability. This investigation covers a theoretical analysis of braking influence on yaw stability on unloaded 4×2 tractors, being applicable to vehicle braking while cornering, including steering induced by other asymmetrical forces, since it focuses essentially on small steering angles.

Residual stress and hardness in steel due to thermal, mechanical, and fatigue deformations are determined by an X-ray diffraction method. The sharp temperature rise associated with electrical discharge machining causes austenitizing, rehardening, and tempering, and results in high tensile residual stress. Shot-peening quality is evaluated from residual stress and hardness induced by the peening. Rolling contact fatigue of carburized and hardened bearings causes a transformation of austenite to martensite, and thereby generates more residual compression, and also causes permanent fatigue softening. Less softening is observed in inner races of consutrode and cross-forged steels than in air-melted steel, and the former steels exhibit greater fatigue life at early and mean failure levels.

Externally applied unbalanced forces and their corresponding impulses are generally excluded from consideration in regards to the evaluation of the collision phase events for a system comprised of two motor vehicles undergoing collinear impact. This exclusion is generally warranted secondary to the fact that the collision force and its corresponding impulse are dominant during the collision phase. Conceptually, two exclusions exist to this approach. The first is the situation in which significant physical restraints are present to the displacement of one or both collision partners and are of sufficient magnitude as to require inclusion. Generally, this represents the exceptional case and includes, but is not limited to, situations in which one vehicle is snagged, in a non-eccentric manner, by a rigid narrow-width object such as a pole or other similar restraint, prior to the occurrence of the subsequent vehicle-to-vehicle collision under evaluation.

Over the past years many have been predicting various dramatic changes in the vehicle including automatic route guidance, the office in the vehicle, and the auto PC. There are a number of factors which need to come together before significant momentum can develop toward realizing any of these predictions. This paper enumerates these factors and explores the current state and possible evolution of each. While each of these factors could stall progress, the linchpin is likely to be wireless communication. The current state of wireless and its capabilities going forward are examined in depth.

This paper presents an overview of a new class of wireless acceleration sensor chips being developed by Evigia Systems and Air Force Research Laboratory (AFRL) that can record the magnitude and duration of exposure to external impact without requiring any battery or any other external power source. The combination of the magnitude and duration of the acceleration event provides the information needed for quantification of the impact energy after extracting the recorded data from the sensor array. The light-weight, small form-factor, and wireless link features of these chips enables them to be readily inserted in earplugs, helmets, protective gear, on sections of vehicles. Further, their low cost, make them well suited for the Go-Kart, Sprint Car, Rally and Motocross races where the budgets are lower than IRL or NASCAR.