Search Results

A NEW TEST is described for studying the oxidation stability of automatic transmission fluids (ATF). The test shows an excellent correlation with transmission oxidation tests and points out the importance of time as a variable in such studies. Carefully controlled automobile dynamometer tests have been used to study the shear stability of ATF's. Data are presented showing a comparison of driving conditions, transmissions, and V.I. improvers on shear stability. Results are related to the 50-hr Hydra-Matic durability test. The poor reproducibility of rubber swell measurements on commercial transmission seals is due largely to differences in the rubber compounds. A great improvement in the reproducibility may be made by taking into account the specific gravity of the rubber sample.*

Both “Zytel” nylon resin and “Teflon” tetrafluoro-ethylene resin are being used extensively as bearing materials. Most of these applications have been developed independently and no attempt has been made to collect performance data in order to put future design on a firm basis. Typical data on dry or partially lubricated bearings have been collected from a variety of sources. Work in our laboratories on lubricated bearings made of “Zytel” are reported for the first time. In addition, physical properties of these materials are described. With these properties and the bearing work done to date, it is believed that the selection of the material and the design of bearings can be done with greater accuracy.

This paper demonstrates the possibilities of using Automotive waste plastic material from “end of life” vehicles (ELVs), in the Footwear Industry to manufacture shoe components. The study establishes the sustainability of the flow of ELVs, from the European Car Parc and identifies and estimates the quantity of plastic materials potentially available for recycling from ELVs. Four potential materials, Acrylonitrile/butadiene/styrene (ABS), Polypropylene (PP), Polypropylene/ethylene/propylene/diene (PP/EPDM) and Polyamide (PA), were identified and three materials (PP, PP/EPDM and ABS) were reprocessed from ELV components and evaluated by the Footwear Industry. As a result, ABS was recommended as an economically, suitable replacement for HIPS, the current material used for manufacturing shoe heel components.

In general for Vehicle-to-Vehicle (V2V) communication, message authentication is performed on every received wireless message by conducting verification for a valid signature, and only messages that have been successfully verified are processed further. In V2V safety communication, there are a large number of vehicles and each vehicle transmits safety messages frequently; therefore the number of received messages per second would be large. Thus authentication of each and every received message, for example based on the IEEE 1609.2 standard, is computationally very expensive and can only be carried out with expensive dedicated cryptographic hardware. An interesting observation is that most of these routine safety messages do not result in driver warnings or control actions since we expect that the safety system would be designed to provide warnings or control actions only when the threat of collision is high.

”U” bolts are fixing elements and they are used to clamp an elastic joint. From the past, they still looking as an old design and unfortunately, suspension engineers are not specialists in fasteners and elastic joints. That is why we will show important assumptions and concepts to design and specifications this clamp element “U” bolt and its influence over leaf-springs. Currently, “U” bolt is used to clamp an elastic or elastic-plastic joint of heavy duty suspension, formed by leaf-spring, axle, spring pad, “U” bolt plate. This kind of suspension is typically used to trucks, buses and trailers. We are wondering, which one important assumption that an engineer must be careful when designs a new suspension changing from old designs to an updated technology. We provide a theoretical analysis and a FEA analysis to compare torque efficacy x leaf-spring reactions and what are effects this relationship can cause in a suspension.

Collins Aerospace, a subsidiary of United Technologies Corporation (UTC), has laid out its plans for what is calling “The Grid” – an 25,000-square-foot advanced electric power systems laboratory for designing and testing next-generation, more-electric aircraft technologies for commercial, military, and business aviation.

Countless articles and publications3,4,5 have documented and proven the efficacy, benefits and value of operating within a lean system. Furthermore, there exists common agreement amongst leading organizations successfully implementing a lean system that in order to do so it must take into consideration the entire enterprise, that is, from supplier to customer and everything in between6. One of the core issues this paper addresses is when the optimal time is to train and educate the people who currently have, or will have, influence over the ‘enterprise’.

TFC/IW, total fuel consumption divided by inertia weight is reported with other engineering variables for recent EPA data for industry passenger cars and truck. TFC/IW is used in comparisons between gasoline and diesel engines, 49 States and California, passenger cars and trucks. The California fuel economy penalty due to more stringent emissions standards is discussed. The relationship between TFC/IW and ton miles per gallon is shown. Special attention is focused on 4 cylinder gasoline powered vehicles in 49 States passenger car fleet. The use of TFC/IW to answer the question, ‘What Changed?’ when comparing the fuel economies of two fleets is described.

Proper lubrication of moving parts is a critical factor in internal combustion engine performance and longevity. Determination of ideal lubricant change intervals is a prerequisite to ensuring maximum engine efficiency and useful life. When oil change intervals are pushed too far, increased engine wear and even engine damage can result. On the other hand, premature oil changes are inconvenient, add to vehicle maintenance cost, and result in wasted natural resources. In order to determine the appropriate oil change interval, we have developed an oil condition sensor that measures the electrical properties of engine oil, and correlates these electrical properties to the physical and chemical properties of oil. This paper provides a brief background discussion of the oil degradation process, followed by a description of the sensor operational principles and the correlation of the sensor output with physical and chemical engine oil properties.

IT does not yet seem to be recognized fully that it is the local temperature at the surface of contact and not the local specific pressure that chiefly determines the occurrence of seizure under extreme-pressure-lubrication conditions. This local temperature is the result of the temperature level of the parts lubricated, considered as a whole (“bulk” temperature) and of a superimposed instantaneous temperature rise (temperature “flash”) which is localized in the surface of contact. It appears typical for extreme-pressure-lubrication conditions, as met in gear practice, that the temperature flash is much higher than the bulk temperature. With existing conventional test methods for the determination of the protection against seizure afforded by EP lubricants, a considerable rise of the bulk temperature mostly occurs; as it cannot be controlled sufficiently; thus, leaving an unknown margin for the temperature flash, it renders impossible a reliable determination.

High performance lubricant additive systems have been developed to formulate SAE 5W-30 passenger car engine oils which meet current and anticipated requirements of the North American original equipment manufacturers. The trend in North America is to recommend SAE 5W-30 oils that not only meet the API SF requirements for gasoline engines (“first-generation” oils), but also meet the stringent API CC requirement for light duty diesel engines (“second-generation” oils). Furthermore, the engine builders have issued “world specifications” for motor oils which incorporate additional “second-generation” SAE 5W-30 characteristics, such as enhanced API SF limits, improved fuel efficiency, an increased margin of bearing protection, and lower finished-oil phosphorus levels. The additive systems described herein exceed API SF and CC requirements as well as “second-generation” performance hurdles.

There are many different vibration sources in a car. Engine, gears, road roughness, impacts against the wheels cause vibration and sound that can decrease the parts and the car durability as well as affect drivability, safety and passengers and community comfort. In 4×4 cars, some extra vibration sources are the parts responsible for transmitting the torque and power to the rear wheels. Each of them has their own vibration modes, excited mostly by its imbalance or by the second order engine vibration. The engine vibration is a very well known phenomena and the rear driveshaft is designed not to have any vibration mode in the range of frequencies that the engine works or its second order. The imbalance of a driveshaft is also a design requirement. That means, the acceptable imbalance of the driveshaft is limited to a maximum value.

In this paper, remanufacturing will be explored as a feasible option to maintaining the serviceability of electronic modules fitted to vehicles entering their service life from year four (after warranty) and beyond. Understanding the makeup of each module (content, design, and complexity) determines the feasibility of remanufacturing along with its cost effectiveness. Problems exist storing components for many years and engaging in periodic manufacturing is not cost competitive for high content modules. Thus, if reverse capability is not an option, then remanufacturing is a viable solution that, for certain modules, is a cost effective and an environmentally responsible (sustainable) solution to the service parts dilemma.

Estimation of soot deposited on a wall flow type DPF, is a vital information to ensure safe and efficient DPF management. Accuracy in determining mass of soot present inside the DPF ensures a correct regeneration management strategy in-terms of fuel efficiency and DPF safety considering soot overloading and too frequent regenerations. It also ensures an efficient detection of anomalies in the PM filtration mandated by the BSVI/EURO VI legislation as a part of On-board diagnostics. Classical approach of determining soot present inside DPF involves monitoring increase in pressure drop. Real time usage of such a model is limited by the inaccuracy of measuring pressure drop at low exhaust flows. Hence, contemporary engine controllers use pressure drop based models as a failsafe and estimate DPF soot loading by modelling soot release rate due to engine combustion and the rate at which it is oxidized.

This paper describes some of the design solutions adopted in solving two major problems besetting man-powered aircraft in use: that of breakage and storage. It describes work leading up to the building and testing of “Phoenix”, a man-powered aircraft with a polyester-film inflatable wing. The paper deals mainly with aspects relating to the wing design and construction.

A large number of testing procedures have been developed to ensure vehicle safety in common and extreme driving situations. However, these conventional testing procedures are insufficient for testing autonomous vehicles. They have to handle unexpected scenarios with the same or less risk a human driver would take. Currently, safety related systems are not adequately tested, e.g. in collision avoidance scenarios with pedestrians. Examples are the change of pedestrian behaviour caused by interaction, environmental influences and personal aspects, which cannot be tested in real environments. It is proposed to use augmented reality techniques. This method can be seen as a new (Augmented) Pedestrian in the Loop testing procedure.